• Tribology and Lubricants
• /
• v.16 no.2
• /
• pp.84-90
• /
• 2000

High Temperature wear behavior of plasma sprayed zirconia coatings containing up to 10 mol% of Fe$_2$O$_3$ were investigated. The wear test results showed that the addition of Fe$_2$O$_3$ particles to zirconia improved the wear resistance and lowered the coefficient of friction. Optimum concentration of Fe$_2$O$_3$ was about 5 mol%. Similar degradation behavior was observed at about 40$0^{\circ}C$ for both zirconia and Fe$_2$O$_3$ added zirconia coatings. The results indicated that stabilization of tetragonal phase and changes in mechanical properties such as hardness and toughness were responsible for tribological behavior of plasma sprayed zirconia contain Fe$_2$O$_3$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.739-752
• /
• 1989

The temperature distribution and heat flux of the inner wall of the cylinder of turbocharged gasoline engine were calculated by the 3-dimensional heat conduction analysis employing boundary element method. Overall mean effective heat transfer coefficient and thermal resistance ratio and equivalent thickness of the cylinder wall were calculated. the numerical results were discussed with respect to the engine speed, equivalence ratio, spark and boost pressure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.962-967
• /
• 2017

The Diamond-Like-Carbon (DLC) coating is a new carbon-based amorphous material. Carbon ions in the plasma are electrically accelerated and collide with the substrate to form a thin film. This film has similar properties to diamonds such as high surface hardness, low coefficient of friction, corrosion resistance and durability that do not react with acids and bases. Also, since there is no thermal deformation, it can be printed at room temperature. and coated on almost all materials such as paper, polymer, ceramics and various metals even aspheric lens it is possible to mirror surface coating with excellent surface roughness. In this paper, we have analyzed the DLC film formed by Filtered Arc Ion Plating (Filtered AIP) process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.448-449
• /
• 2008

Light Mg alloy stands on the center of investigation due to the high potential of industrial application not only to the structural, but also to the functional fields. However, the intrinsic low strength and corrosion resistance have limited to extend its industrial use. In order to overcome the disadvantage, various attempts have been come to the modification of composition, resulting in finding Mg-Zn-Y alloys. The cast Mg-Zn-Y alloy leads to the high strength and hardness, low friction coefficient and low interfacial energy in both the ambient and elevated temperature.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.31-36
• /
• 2000

High temperature and pressure materials in power plant are degraded by creep damage, if they are exposed to constant loads for long times, which occurs in the load bearing structures of pressurized components operating at elevated temperatures. Many conventional measurement techniques such as replica method, electric resistance method, and hardness test method for measuring creep damage have been used. So far, the replica method is mainly used for the Inspection of High temperature and pressure components. This technique is, however, restricted to applications at the surface of the testpieces and cannot be used to material inside. In this paper, ultrasonic evaluation for the detection of creep damage in the form of cavaties on grain boundaries or integranular microcracks are carried out. And the absolute measuring method of quantitative ultrasonic velocity technique for Cr-Mo material degradation is analyzed. As a result of ultrasonic tests for crept specimens, we find that the sound velocity is decreased as the increase of creep life fraction$({\Phi}_c)$ and also, confirmed that hardness is decreased as the increase of creep life fraction$({\Phi}_c)$ but the coefficient of ultrasonic attenuation is increased as the increase of creep life fraction$({\Phi}_c)$. Finally based on the result in this paper, it can be recognized that the ultrasonic techniques using velocities and attenuation coefficient factor are very useful non-destructive methods to evaluate the degree of material degradation in fossile power plants.

• Korean Journal of Materials Research
• /
• v.22 no.12
• /
• pp.650-657
• /
• 2012

For the purpose of improving the durability problem, translucent opal glass was fabricated as a substitute for the polycarbonate diffuser of LED lighting. Calcium phosphate was used as an opacifier of opal glass and melted in an electric furnace. The opaque effect was identified according to the change of the cooling procedure. As results, translucent opal glass was obtained by the melting of a batch with a composition of 3.8% calcium phosphate at $1550^{\circ}C$ for 2 hrs and then the cooling of the material in the furnace. For the cooling condition of the glass sample, HTCG (High Temperature Cooled Glass) was found to have better optical properties than LTAG (Low Temperature Annealed Glass). It had excellent optical properties for a diffuser of LED lighting, with no dazzling from direct light due to its high haze value of over 99% and low parallel transmittance value of under 1%. For the thermal properties, it had an expressed thermal expansion coefficient of $5.7{\times}10^{-6}/^{\circ}C$ and a softening point of $876^{\circ}C$; it also had good thermal properties such as good thermal shock resistance and was easy to apply to the general manufacturing process in the forming of glass tubes and bulbs. Therefore, it is concluded that this translucent opal glass can be used as a glass diffuser material for LED lighting with high heat resistance and high durability; this material is suitable as a substitute for polycarbonate diffusers.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.16 no.3
• /
• pp.9-18
• /
• 1979

In this paper, we fabricated a samiconductor C. T. R.(Critical Temperature Resisthor) using vanadium-oxides as material and measured its electrical characteustics. Experimental results are as follows; (1) The abrupt resistance change coefficient of the fabricated C. T, R., , is approximately 3 and (2) the value of depends largely on the reducing time and quenching time and also (3) the C. T, R. with larger value of has shorter switching time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.347-350
• /
• 1995

In this paper, we fabricated fuel shortage detecting sensor, utilizing NTC thermistor concerned with Mn-Ni-Co system. We would be obtained B constant value of 1930∼2080 and resistivity 387∼430(ohm-cm) additive Bi$_2$O$_3$0∼0.5 wt% to Mn$_3$O$_4$:9wt%, Co$_3$O$_4$:61wt%, NiO:28wt% under 1150∼1250$^{\circ}C$ of sintering temperature. In sensor, we obtained characteristics, which we want, in resistance range 850∼l150$\Omega$, B constant 2000${\pm}$5%. we can see 15 multiplied differences between gasoline and heat dissipation coefficient of air condition.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.640-645
• /
• 2007

An experimental apparatus to show the hot spot cooling of an IC chip using a thermoelectric cooler is developed. The spot heating in very small area is achieved by the applying CO$_2$ laser source and temperatures are measured using miniature thermocouples. The active effects of thermoelectric cooler on the hot spot cooling system such as rapid heat spreading in the chip and lowering the peak temperature around the hot spot region are investigated. The experimental results are simulated numerically using the TAS program, which the performance characteristics such as Seebeck coefficient, electrical resistance and thermal conductivity of the thermoelectric cooler are searched by trial and error. Good agreements are obtained between numerical and experimental results if the appropriate performance data of the thermoelectric cooler are given.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1218-1230
• /
• 1994

In manufacturing process of porous glass-ceramics by the filler method, the sintering behaviour of crystallizable glass powder mixed with various salts was studied and also the effects of precipitated crystal phases on the properties of porous glass-ceramics were investigated. Fine-grained crystallizable glass powder was homogeneously mixed with various slat having grain size 100~200 ${\mu}{\textrm}{m}$ and sintered for densification. After washing out the inorganic salt with distilled water, the porous sintered body was heat treated additionly for crystallization. The MgO-Al2O3-SiO2 base glass was used as crystallizable glass powder and the water soluble salts such as K2SO4 and MgSO4 were used as filler. When K2SO4 was used, leucite crystal phase was formed as a result of the ion exchange and porous glass-ceramics which exhibit high temperature resistance and high thermal expansion coefficient of 17$\times$10-6/$^{\circ}C$ could be obtained. On the contrary, when MgSO4 was used, only slight ion exchange is observed and $\mu$-cordierite and $\alpha$-cordierite crystal phases were formed and porous glass-ceramics which exhibit low thermal expansion coefficient schedule were determined with the results of DTA curves, thermal shrinkage curves and XRD patterns analysis. From DTA curves and thermal shrinkage curves, it was found that the sintering densification have been completed at the temperature range of exothermic peak for crystallization. The pore size distributions and pore diameters were measured by mercury porosimeter. The pore diameter of porous glass-ceramics was 10~15 ${\mu}{\textrm}{m}$ when 100~200${\mu}{\textrm}{m}$ grain size of K2SO4 was used and it was 25~30 ${\mu}{\textrm}{m}$ when the same grain size of MgSO4 was used. The porous glass-ceramics K2SO4 used shows bimodal pore size distribution and its porous skeleton structure was ascertained by SEM observation.