• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.14-21
• /
• 2003

Thin films of ZrO$_2$ and TiO$_2$ were deposited on Si(100) substrates using RF magnetron sputtering technique. To study an influence of the sputtering parameters, systematic experiments were carried out in this work. XRD data show that the $ZrO_2$ films were mainly grown in the [111] orientation at the annealing temperature between 800 and $1000^{\circ}C$ while the crystal growth direction was changed to be [012] at above $1000^{\circ}C$. FT-IR spectra show that the oxygen stretching peaks become strong due to $SiO_2$ layer formation between film layers and silicon surface after annealing, and proved that a diffusion caused by either oxygen atoms of $ZrO_2$ layers or air into the interface during annealing. Different crystal growth directions were observed with the various deposition parameters such as annealing temperature, RF power magnitude, and added $O_2$ amounts. The growth rate of $TiO_2$ thin films was increased with RF power magnitude up to 150 watt, and was then decreased due to a sputtering effect. The maximum growth rate observed at 150 watt was 1500 nm/hr. Highly oriented, crack-free, stoichiometric polycrystalline $TiO_2$<110> thin film with Rutile phase was obtained after annealing at $1000^{\circ}C$ for 1 hour.

• Journal of the Korean institute of surface engineering
• /
• v.40 no.2
• /
• pp.91-97
• /
• 2007

In this study we investigated the oxygen effect on the nucleation and its residual stress during unbalanced magnetron sputtering. Up to 0.5% in oxygen flow rate, cubic phase (c-BN) was dominated with extremely small fraction of Hexagonal phase (h-BN) of increasing trend with oxygen concentration, whereas hexagonal phase is dominated beyond 0.75% flow rate. Interestingly, the residual stress in cubic-phase-dominated films was substantially reduced with small amount of oxygen (${\sim}0.5%$) down to a low value comparable to the h-BN case. This may be because oxygen atoms break B-N $sp^3$ bonds and make B-O bonds more favorably, increasing $sp^2$ bonds preference, as revealed by FTIR and NEXAFS. It was confirmed by experimental facts that the threshold bias voltage for nucleation and growth of cubic phase were increased from -55 V to -70 V and from -50 V to -60 V respectively. The reduction of residual stress in O-added c-BN films is seemingly resulting from the microstructure of the films. The oxygen tends to increase slightly the amount of h-BN phase in the grain boundary of c-BN and the soft h-BN phase of 3D network including surrounding nano grains of cubic phase may relax the residual stress of cubic phase.

• Korean Journal of Food Science and Technology
• /
• v.16 no.2
• /
• pp.143-148
• /
• 1984

The effects of various nutrients added to soy protein concentrate (SPC)-yogurt on the growth of Lactobacillus acidophilus and the flavor of SPC-yogurt were investigated. Soy milk was prepared from SPC (4.2% as protein) and various nutrients. One hundred ml of the prepared soy milk was given proper heat treatment, inoculated with 2.5ml of 24 hr-old culture, and incubated for 24 hr at $37^{\circ}C$. The growth of L. acidophilus was estimated from viable cell counts, titratable acidity and pH. The growth curve obtained from the experiment suggested that the log phase ended after 6 hr and the stationary phase ended after 30 hr. Glucose and fructose greatly enhanced the acid production by L. acidophilus. The optimum concentration of these two sugars in the media was approximately 3% each. Yeast extract greatly stimulated the acid production by L. acidophilus, and the optimum concentration of this additive was approximately 0.5%. Higher concentration of SPC resulted in slightly higher acidity in soy yogurt.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.282-287
• /
• 2023

The effect of stress relief heat treatment temperature and duration time on the microstructure, residual stress and Vickers hardness of additively manufactured Ti-6Al-4V alloy using laser powder bed fusion process was clarified. As a result of stress relief heat treatment for 240 minutes at 823 K and 60 minutes or more at 873 K, residual stress was decreased less than 30 MPa without grain growth and phase transformation which causes dimensional distortion and deterioration of mechanical properties. In addition, hardness was increased with increasing heat treatment temperature and duration time. It was deduced that the refinement of acicular martensitic α' phase due to the increasing duration time of isothermal heat treatment at 773~873 K, which was not detected by XRD and phase map analysis using SEM-EBSD, probably increases the hardness.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.2
• /
• pp.229-237
• /
• 1996

The superconducting phase, $YBa_{2}Cu_{3}O_{x}$ (YBCO), was in-situ deposited on the single crystal MgO substrates, using an aerosol decomposition process in a cold plasma reactor. The solubility and decomposition temperature of the chemical precursors, and the vapor pressures of the solvents, were determined to be the factors crucial to achieving a stoichiometric, crystalline YBCO phase. The deposition parameters for the YBCO phase were 0.3 to 2.7 kPa for the oxygen partial pressure and $800^{\circ}C$ to $940^{\circ}C$ for the substrate temperature. The optimum deposition conditions for the YBCO phase were observed along the CuO decomposition line.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.475-479
• /
• 1999

Langasite ($La_{3}Ga_{5}SiO_{14}$) was found to have wide application as a promising piezoelectric material. It has high thermal stability of the frequency and large electromechanical coupling factor. For the further development of new compounds with langasite type structure, powders in the La-Al-Si-O system were synthesized by a modified Pechini process. The evolution of the crystalline phase during calcination was studied using TG-DTA, XRD and TEM for the precursor powders. Decomposition proceeded via dehydration and removal of excess solvents at low temperatures ($T<500^{\circ}C$), followed by the crystallization of lanthanum aluminum silicate ($T>800^{\circ}C$) and phase transformation to $LaAlO_{3}$ phase ($T>1200^{\circ}C$). Transmission electron microscopy (TEM) of the calcined powders showed diffuse hollow rings corresponding to an amorphous phase at $800^{\circ}C$ and clear diffraction patterns corresponding to a crystalline phase from the P321 space group ($T<1200^{\circ}C$) and the R3m ($T<1200^{\circ}C$).

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.498-502
• /
• 2002

Pure-yttrium iron garnet($Y_3Fe_5O_{12}$2, YIG) thick films were grown from a $PbO/B_2O_3$ flux onto (111) SGGG substrate using liquid phase epitaxy. The effect of substrate rotation speed and supercooling on crystallinity, chemical composition and growth rate of the thick films was investigated. The FWHM of films decreased with increasing of growth temperature from 860 to 910${\circ}C$. A substrate rotation speed of 120 rpm at 910${\circ}C$ lead to growth rates up to $60{\mu}m/h$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.6
• /
• pp.256-259
• /
• 2006

The amorphous $SiO_x$ nanowires were synthesized by the vapor phase epitaxy (VPE) method. $SiO_x$ nanowires were formed on silicon wafer of temperatures ranged from $800{\sim}1100^{\circ}C$ and nickel thin film was used as a catalyst for the growth of nanowires. A vapor-liquid-solid (VLS) mechanism is responsible for the catalyst-assisted amorphous $SiO_x$ nanowires synthesis in this experiment. The SEM images showed cotton-like nanostructure of free standing $SiO_x$ nanowires with the length of more than about $10{\mu}m$. The $SiO_x$ nanowires were confirmed amorphous structure by TEM analysis and EDX spectrum reveals that the nanowires consist of Si and O.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.485-492
• /
• 2012

Dense and single phase $BiFeO_3$ (BFO) ceramics were prepared using attrition milled calcined (coarse) powders of an average particle size of ${\approx}3{\mu}m$ by conventional sintering process. A relative density of ${\approx}96%$ with average grain size $7.3{\mu}m$ was obtained when the powder compacts were sintered at $850^{\circ}C$ even for a shorter duration of 10 min. In contrast, densification barely occurred at $800^{\circ}C$ for up to 12 h rather the microstruce showed the growth of abnormal grains. The grain growth behavior at different temperatures is discussed in terms of nonlinear growth rates with respect to the driving force. The sample sintered at $850^{\circ}C$ for 12 h showed enhanced electrical properties with leakage current density of $4{\times}10^{-7}A/cm^2$ at 1 kV/cm, remnant polarization $2P_r$ of $8{\mu}C/cm^2$ at 20 kV/cm, and minimal dissipation factor (tan ${\delta}$) of ~0.025 at $10^6$ Hz. These values are comparable to the previously reported values obtained using unconventional sintering techniques such as spark plasma sintering and rapid liquid phase sintering.

• Journal of Animal Science and Technology
• /
• v.61 no.4
• /
• pp.234-238
• /
• 2019

This experiment was conducted to evaluate the effects of dietary protease on growth performance, blood constituents, and carcass characteristics of growing-finishing pigs. A total of 48 growing pigs (initial body weight, $34.8{\pm}0.62kg$) were randomly assigned to 2 dietary treatments (6 pigs/pen; 4 replicates/treatment). The treatments were a diet based on corn and soybean meal (CON) and CON supplemented with 0.01 % of protease (PRO). Pigs were fed respective dietary treatments with a 2-phase feeding program for 12 weeks. Pigs fed PRO had higher average daily gain (ADG; phase I, 866.38 vs. 821.75 g/d; overall, 910.96 vs. 866.30 g/d; p < 0.05) and gain to feed ratio (G:F; phase I, 0.345 vs. 0.363 g/g; p < 0.05) than those fed CON. However, there were no differences on blood constituents and carcass characteristics between CON and PRO of growing-finishing pigs. In conclusion, dietary protease supplementation in the typical diet for growing-finishing pigs improved growth rate.