• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.321-328
• /
• 2014

Software defined radar (SDR) is a multi-purpose radar system where most of the hardware processing is performed by software. This paper introduces a concept and technology trends of software defined radar, and addresses the advantages and limitations of the current SDR radar systems. For the advanced SDR concept, the KAU SDR Model (KSM) is presented for the multimode and multiband radar system operating in S-, X-, and K-bands. This SDR consists of a replaceable multiband antenna and RF hardware, common digital processor module with multimode, and open software platform based on MATLAB and LabVIEW. The new concept of the SDR radar can be useful in various applications of the education, traffic monitoring and safety, security, and surveillance depending on the various radar environments.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.767-775
• /
• 2018

To develop and check a Radar Processor Unit, checking the function and performance of the requirement is very important factor in developing Radar. General methods for verifying the Radar is simulation test, environment linkage test and field operation test, firstly, in case of requirement analysis phase, verify Radar algorithm and design by using mathematical method based simulation test method, and secondly, in case of unit test and integrated test phase, Test Equipment is set to simulate radar environment in the lab to verify radar function and performance. Lastly, field operation test phase is carried out to confirm the function and performance after it is mounted on the actual equipment. To successfully develop Radar Processor Unit, using the method of field operation test method after sufficient test cases are tested in radar environmental interlocking method in order to save cost and testing period and because of this reason, development of the Radar Processor Unit Test Equipment is becoming very important factor. In this paper, we introduce the concept of test equipment development and important factors in test equipment, which are target simulation, data processing and device interlocking.

• International journal of advanced smart convergence
• /
• v.9 no.2
• /
• pp.114-122
• /
• 2020

When replacing hardware due to obsolescence, discontinuation, and expansion of software-equipped electronic equipment, software changes are required in the past, but if virtualization technology is applied, it can be applied without software changes. In this regard, we studied in order to apply virtualization technology in the development of naval multi-function radar signal processing, we studied hardware and OS independency for Docker and performance comparison between Docker and virtual machine. As a result, it was confirmed that hardware and OS independence exist when using Docker and that high-speed processing is possible compared to the virtual machine.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1797-1801
• /
• 2004

In this paper we show the hardware testbed and software simulator of multi function array radar (MFAR). The hardware MFAR is simple and flexible hardware to implement various radar beamforming and detecting algorithms. To overcome the limitation of hardware MFAR, the software simulator is proposed. User can simulate radar under the various environment conditions adjusting the parameter of simulator. User can set environment of radar, such as the location and velocity of target, jammer and the terrain clutter. The radar use various probing pulses and supports two operation mode, surveillance and tracking mode.

• Journal of Multimedia Information System
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2017

In recent years, the quixotic nature and concentration of rainfall due to global climate change has intensified. To monitor localized heavy rainfalls, a reliable disaster monitoring and warning system with advanced remote observation technology and high-precision display is important. In this paper, we propose a GIS-based intuitive and realistic 3D radar data display technique for accurate and detailed weather analysis. The proposed technique performs 3D object modeling of various radar variables along with ray profiles and then displays stereoscopic radar data on detailed geographical locations. Simulation outcomes show that 3D object modeling of weather radar data can be processed in real time and that changes at each moment of rainfall events can be observed three-dimensionally on GIS.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.6 no.5
• /
• pp.281-286
• /
• 2011

FMCW Radar sensor is commonly used for an automobile collision avoidance system for rider's safe. Systems using FMCW radar, however, would be one of expensive solutions for just simple rear obstacle detection purpose due to its high cost. In this letter, a short range rear obstacle detector using novel 24GHz AM radar sensor is presented. It can be implemented at significantly lower cost than FMCW radar for practical commercialization. The proposed AM radar sensor module is fabricated in a single aluminum housing to reduce the overall size while using single power supply voltage of 12V with 1200mA current for automotive applications. The measured detection range is up to 210cm with 10cm of distance resolution, which is suitable for a parking assistance system for automobiles.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.602-609
• /
• 2021

Aircraft radar has special function which is ranging from aircraft to ground of antenna boresight. Because ranging information is used to calibrate altitude of aircraft or to drop a conventional bomb, the measuring have to be precise and robust. Therefore, we propose a simple and efficient method using monopulse radar for ground ranging. Proposed method calculates balancing weight according to linearity of monopulse ratio and mixes two ranging measurements in proportional to the weight. By exploiting balancing weight, radar is able to react to various environment as monopulse ratio contains characteristics of clutter environment. As a result, robust ranging information can be achieved. We use DEM(Digital Elevation Model) in order to simulate heterogeneous environment. In experimental result, it is shown that proposed method shows better accuracy and precision in any environment.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.2
• /
• pp.151-159
• /
• 2022

In this paper, we implement a digital multi-beamformer using FPGA(Field Programmable Gate Array) which has advantages in parallel and real-time data processing. This is accomplished through the use of not only high-speed data communication but also multiple beam forming, which is currently required by MFR(Multi Function Radar). As a result, the beamformer can process 24 Gbps throughput in real-time and form 5 digital beams at the same time. It is also compared to the results of Matlab simulations. We demonstrate how an implemented beamformer can be used in an MFR system by using a digital array antenna.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.08a
• /
• pp.208-216
• /
• 2004

Since 2000, the authors have been developing remote radar network system to observe the vessel traffic in Tokyo Bay. In December 2002, the first operational remote radar station was set at the National Defense Academy in Yokosuka, and vessel traffic observation was started. However, it was impossible to perform accurate observation in the northern part of Tokyo Bay by this Yokosuka radar station only. In September 2003, the second remote radar station and AIS receiving station were installed at Higashi Ogishima in Kawasaki. This second radar enabled us to carry out accurate observation in that area. Both radars can be remotely controlled from the monitoring station in Tokyo University of Marine Science and Technology. On September 30 and October 1,2003, the vessel traffic observation was carried out using both radars. Combining radar images observed by both radars, the ships' tracks were taken and the dangerous ships were extracted by using SJ value and Bumper Model. The time changes of dangerous ship density in some areas in Tokyo Bay and utilization ratio of the traffic routes were also investigated. In addition, analyzing the AIS date received at Kawasaki station, the positions and speed vectors of the ships equipped with AIS were shown.

• Journal of Ocean Engineering and Technology
• /
• v.24 no.1
• /
• pp.47-52
• /
• 2010

This study presents a modified scheme for the radar image simulation of sea waves. A simulated radar image was obtained by taking into account the dot product of the directed vector from the radar and the normal vector of the sea surface. Moreover, to calculate the radar image, we used the radar received power and radar cross section. To demonstrate the effectiveness of the proposed scheme, the wave spectrum from field data was utilized to obtain the simulated sea waves. The radar image was simulated using numerically generated sea waves. The wave statistics from the simulation agrees comparatively with those of the original field data acquired by real radar measurements.