• Korean Journal of Materials Research
• /
• v.13 no.7
• /
• pp.429-435
• /
• 2003

In this study the new creep test using miniaturized specimen(10${\times}$10${\times}$0.5 ㎣) was performed to evaluate the creep characteristics for degraded materials of 2.25Cr-1Mo steel. For this creep test, the artificially aged materials for 330 hrs and 1820hrs at $630^{\circ}C$ were used. The test temperatures applied for the creep deformation of miniaturized specimens was X$630^{\circ}C$ and the applied loads were between 45 kg∼80 kg. After creep test, macro- and microscopic observation were conducted by the scanning electron microscope(SEM). The creep curves depended definitely on applied load and microstructure and showed the three stages of creep behavior like uniaxial tensile creep curves. The load exponents of virgin, 330 hrs and 1820 hrs materials based on creep rate showed 14.8, 9.5 and 8.3 at $550^{\circ}C$ respectively, The 1820 hrs material showed the lowest load exponent and this behavior was also observed in the case of load exponent based on creep rupture time. In contrast to virgin material which exhibited fined dimple fractography, a lot of carbides like net structure and voids were observed on the fractography of degraded materials.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.11
• /
• pp.116-123
• /
• 2009

The elastic properties of core affect mechanical properties and deformation behaviours of the lightweight sandwich panel. The objective of the present paper is to estimate experimentally Young's and shear moduli of a core in internally structured boned (ISB) panel with woven metal as inner structures using the deflection theory of sandwich beam considered core stiffness. Three points bending experiments were performed to obtain force-deflection curves of the designed ISB panel in each material direction. The elastic and shear moduli of the core in each material direction were estimated from slopes and intercepts of relationships between compliance per the span length and square of the span length, respectively. The results of the estimation showed that the fabric technology of the woven metal affects the variation of the elastic properties in the core. Through the comparison of shear moduli and force-deflection curves of the proposed method and those without considering the core stiffness, it was shown that the core stiffness should be considered to estimate properly the Young's and shear moduli of ISB panels. Finally, the contribution ratio of bending and shear deflections of ISB panels to the total deflection was quantitatively examined.

• International Journal of Precision Engineering and Manufacturing
• /
• v.5 no.3
• /
• pp.35-42
• /
• 2004

This research describes that the cutting characteristics and tool wear behavior in the micro cutting of three kinds of wear resistant cemented carbides (WC-Co; V40, V50 and V60) using PCD (Poly Crystalline Diamond) and PCBN (Poly crystalline Cubic Boron Nitride) cutting tools by use of the SEM (Scanning Electron Microscope) direct observation method. The purpose of this research is to present reasonable cutting conditions from the viewpoint of high efficient cutting refer to a precise finished surface and tool wear. Summary of the results is as follows: (1) The cutting forces tend to increase as the increase of the weight percentage of WC particles, and the thrust forces was larger than the principal forces in the cutting of WC-Co. These phenomena were different from the ordinary cutting such as cutting of steel or cast iron. (2) The cutting speed hardly influenced the thrust force, because of the frictional force between the cutting tool edge and small WC particles at low cutting speed region such as 2$\mu\textrm{m}$/s. It seemed that the thrust cutting force occurred by the contact between the flank face and work material near the cutting edge. (3) The wear mechanism for PCD tools is abrasion by hard WC particles of the work materials, which leads diamond grain to be detached from the bond. (4) From the SEM direct observation in cutting the WC-Co, it seems that WC particles are broken and come into contact with the tool edge directly. This causes tool wear, resulting in severe tool damage. (5) In the orthogonal micro cutting of WC-Co, the tool wear in the flank face was formed bigger than that in the rake face on orthogonal micro cutting. And the machining surface integrity on the side of the cutting tool with a negative rake angle was better than that with a positive one, as well as burr in the case of using the cutting tool with a negative rake angle was formed very little compared to the that with a positive one.

• The KIPS Transactions:PartD
• /
• v.13D no.7 s.110
• /
• pp.1027-1038
• /
• 2006

There are many technical problems in the recommendation system based on very large database(VLDB). So, it is necessary to study the recommendation system' structure and the data-mining technique suitable for the large scale Internet shopping mail. Thus we design and implement the product recommendation system using k-means clustering algorithm and sequential pattern technique which can be used in large scale Internet shopping mall. This paper processes user information by batch processing, defines the various categories by hierarchical structure, and uses a sequential pattern mining technique for the search engine. For predictive modeling and experiment, we use the real data(user's interest and preference of given category) extracted from log file of the major Internet shopping mall in Korea during 30 days. And we define PRP(Predictive Recommend Precision), PRR(Predictive Recommend Recall), and PF1(Predictive Factor One-measure) for evaluation. In the result of experiments, the best recommendation time and the best learning time of our system are much as O(N) and the values of measures are very excellent.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.56-62
• /
• 2010

This paper presents the development process of roof carrier assembly using a one side release system for a vehicle. An RV(Recreational Vehicle) or SUV(Sports Utility Vehicle) has a roof carrier system on an upper surface of a roof panel for loading large or long size baggage. Such a roof carrier system is comprised of a roof rack longitudinally mounted on a roof panel and cross bar perpendicularly installed in the horizontal direction. Several locking mechanisms used in most vehicle roof carrier systems are composed with both side releasable locking ones. The obvious drawback to this arrangement is that when the user desires to reposition the cross bar, first one of the locking members must be unlocked and then the user must walk around to the opposite side of the vehicle to unlock the other member. In this paper, we proposed a newly locking mechanism, which allows a user simultaneously place both locking members of the roof carrier in locked and unlocked positions. In order to estimate design compatibility, structural and modal analysis is performed. Furthermore, a prototype based on the proposed design has been made, and then durability test carried out. From the simulation and experimental results, the proposed roof carrier system is proved effective and safe.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.1C
• /
• pp.8-16
• /
• 2012

In order for the support of the ETCS (Electronic Toll Collection System) model, which have been operated successfully till now, with multi-lane service, the wireless communication system of the multi-lane-supported ETCS based on RF-DSRC (Radio Frequency - Dedicated Short Range Communication) was used. In this paper, the SME algorithm attaching data flow and form into RFID communication technology was newly suggested to overcome technical problems on RF-DSRC communication system. In addition, in order to verify the SME algorithm, experiments based on ETCS and 900Mhz RFID were carried out. From the result of realization experiment of RFID dependent on the velocity and precision experiment of information inside of RFID, we can see that RFID is detected below 70Km/h and the precision of estimation is more than 90%.

• The Journal of Bigdata
• /
• v.3 no.1
• /
• pp.73-82
• /
• 2018

At the core of future medicine is the realization of Precision Medicine centered on individuals. For this, we need to have an open ecosystem that can view, manage and distribute healthcare data anytime, anywhere. However, since healthcare data deals with sensitive personal information, a significant level of reliability and security are required at the same time. In order to solve this problem, the healthcare industry is paying attention to the blockchain technology. Unlike the existing information communication infrastructure, which stores and manages transaction information in a central server, the block chain technology is a distributed operating network in which a data is distributed and managed by all users participating in the network. In this study, we not only discuss the technical and legal aspects necessary for demonstration of healthcare data distribution using blockchain technology but also introduce KOREN SDI Network-based Healthcare Big Data Distribution Demonstration Study. In addition, we discuss policy strategies for activating blockchain technology in healthcare.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.77-87
• /
• 1994

This paper deals with an automated forming sequence design system by which designers can determine desirable operation sequences even if they have little experience in the design of cold forging process. The forming sequence design in the cold forging is very important and requires many kinds of technical and empirical knowledge. They system isproposed, which generates forming sequence plans for the multistage cold forging of axisymmtrical solid products. Since the process of metal forming can be considered as a transformation of geometry, treatment of the geometry of the product is a key in planning process. To recognize the geometry of the product section, section entity representation and primitive geometries were used. Section entity representation can be used for the calculation of maximum diameter, maximum height, and volume. Forming sequence for the part can be determined by means of primitive geometries such as cylinder, cone, convex, and concave. By utilizing this geometrical characteristics (diameter, height, and radius), the product geometry is expressed by a list of the priitive geometries. Accordingly the forming sequence design is formulated as the search problem which starts with a billet geometry and finishes with a given product one. Using the developed system, the sequence drawing with all dimensions, which includes the proper sequence of operations for the part, is generated under the environment of AutoCAD. Based on the results of forming sequence, process variables(strain, punch pressure, die inner pressure, and forming load) are determined.

• Journal of the Korea Institute of Building Construction
• /
• v.21 no.5
• /
• pp.387-396
• /
• 2021

In building construction, the layout operation is performed to accurately construct the building components in their planned locations, and requires a high level of accuracy and precision. With increases in building size and a lack of skilled laborers, this work has seen an increasing demand for productivity and quality improvements through robot-based construction automation. In particular, the layout work for building structures has a higher need for automation. On this background, this study suggests a direction for the development of an automated layout system of building structures. 5 technical factors and 17 sub-factors were derived based on reviews of existing similar systems, and an evaluation of their importance was carried out through an expert survey. As a result, it was found that the most important factors were driving and marking systems for coping with poor driving and working conditions. In terms of sub-factors, control techniques to secure precision and technologies to automate the overall layout process showed high importance. These findings will contribute to the development of more practical and efficient automation systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.142-144
• /
• 2016

Recent promising technologies of the manufacturing sector interest, and the interest in 3D printing that is expected to cause a huge ripple effect rapidly, and various types of products advertised in accordance with the falling price of 3D printers is spreading. However, the personal 3D printers that are currently being advertised is used for Injection output of the simple type that does not require a high processing precision in accordance with the limitation of technical performance, and consumer satisfaction is very low. In this paper, we propose a 3D printer, 3D precision to overcome existing limitations in the way the printer's high SLA 3D printer that combines injection method and the LSU (Laser Scanning Unit) in the office laser printer polygon mirror scanning method. 3D printers which are proposed to improve the accuracy and manufacturing speed is expected to replace the existing entry-level 3D printer.