• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.4
• /
• pp.342-349
• /
• 2023

In this study, a numerical simulations were conducted to analyze the phase change behavior of a liquid hydrogen storage container. The effects of gravity direction and hydrogen filling rate on boil-off gas (BOG) in the storage container were investigated. The study employed the volume of fluid, which is the phase change analysis model provided by ANSYS Fluent (ANSYS, Canonsburg, PA, USA), to investigate the sloshing phenomenon inside the liquefied hydrogen fuel tank. Considering the transient analysis time, two-dimensional simulation were carried out to examine the characteristics of the flow and thermal fields. The results indicated that the thermal flow characteristics and BOG phenomena inside the two-dimensional liquefied hydrogen storage container were significantly influenced by changes in gravity direction and hydrogen filling rate.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.8
• /
• pp.606-612
• /
• 2014

Vehicle simulation models for noise and vibration prediction have been developed so far generally in two schemes. One is FE models generally used for problems below 200 Hz such as booming noise, and the other is SEA models for high frequencies of more than 1 kHz, representatively related to sound packages. There have been many researches to develop a simulation model for 200~1000 Hz, so-called mid-frequency region, and this paper shows one practical result that covers the trimmed body of a sedan vehicle. The simulation model is developed based on an FE model, and then FE elements at some areas are substituted with SEA elements to reduce DOFs. SEA panels are described by modal density, radiation efficiency, stiffness and damping characteristics that are found from some numerical assessments. Sound packages are modeled similarly as a conventional SEA model. The results obtained from the hybrid model were compared to experimental results. Predicted pressure and vibrational velocity generally show a good agreement. The developed simulation model and related technology are successfully being used in vehicle development process.

• Perspectives in Nursing Science
• /
• v.9 no.2
• /
• pp.111-118
• /
• 2012

Purpose: This study investigated the effects of simulation-based nursing education (for the care of congestive heart failure patients) on self-directed learning competency, clinical knowledge and problem-solving ability among nursing students. Methods: A one-group, pre-post design was utilized with 87 nursing students as the subjects. The scenario of simulation-based nursing education was created using a high-fidelity patient stimulator, and consisted of four states ((1) assessment, (2) reviewing laboratory data and administering medications and treatments, (3) managing increased dyspnea and decreased urine output, and (4) handling the "getting better" state). The simulation-based nursing education included orientation, team-based learning, team-based practice, and debriefing. The data were analyzed using descriptive statistics, Pearson's correlation coefficients and paired t-tests. Results: The scores on the factors for self-directed learning competency (t=-2.57, p= .011), clinical knowledge (t=-6.85, p<.001), and problem-solving ability (t=-3.01, p= .003) increased significantly after the education intervention. Conclusion: Simulation-based nursing education is useful in improving self-directed learning competency, clinical knowledge, and problem-solving ability in nursing students.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2013.12a
• /
• pp.90-93
• /
• 2013

RAM study has been used for various range of industry such as chemical, electronics, defense industry. Recently, in the offshore & shipbuilding industry, demand of owners to analysis risk has been increased. RAM study is a quantitative pointer to risk based design and provides effective method for improvements. This article shows the result of RAM study for LNG fuel supply system. The result provides information to improve design. This study shows how result of risk assessment affects the design of LNG fuel supply system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.08a
• /
• pp.41-52
• /
• 2003

The tendency of current die manufacturing is focusing into development period shortening and panel quality improvement. This brings change of manufacturing process. In existing process, depended on experience, we were faced on a limit of sufficiency in this focus. Thus, we have attempted to make a conquest of that by constructing a process of CAE. Our attempt apply not only draw die formability but also trimming and flanging die formability with simulation of sheet metal. In this paper, we publish effects that were obtained by constructing a process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.822-824
• /
• 2007

This paper investigated a gate driver circuit with amorphous silicon for mobile TFT-LCD. In the conventional circuit, the fluctuation of the off-state voltage causes the fluctuation of gate line voltages in the panel and then image quality becomes worse. Newly designed gate driver circuit with dynamic switching inverter and carry out signal reduce the fluctuation of the off-state voltage because dynamic switching inverter is holding the off-state voltage and the delay of carry signal is reduced. The simulation results show that the proposed a-Si:H gate driver has low noise and high stability compared with the conventional one.

• Journal of the Optical Society of Korea
• /
• v.11 no.3
• /
• pp.85-92
• /
• 2007

In the past, precision optical glass lenses were produced through multiple processes such as grinding and polishing, but mass production of aspheric glass lenses requiring high accuracy and having complex profile was rather difficult. In such a background, the high-precision optical glass molding pressing (GMP) process was developed with an eye to mass production of precision optical glass parts by molding press. In this paper, as a fundamental research to develop the multi-cavity mold for higher productivity of a progressive GMP process used in the fabrication of an aspheric glass lens, an aspheric glass lens forming simulation was carried out.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1334-1336
• /
• 2004

The existing problems of the Electro-Magnetic Suspension system such as air-gap disturbance, mass variation and actuator/sensor failure are described in amore specific manner. These problem can not be solved by conventional state-feedback and output-feedback control. Extended Kalman Filter is to linearize about a trajectory that is continually updated with the state estimates resulting from the measurements. In this paper, first, the physical properties of the EMS system are described. second, Extended Kalman Filer designed as form appliable EMS system. It is shown that state estimation performance can be obtained with the use of Extended Kalman filter, and that results from simulation, stability analyze.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1337-1339
• /
• 2004

The existing problems of the Electro-Magnetic Suspension system such as air-gap disturbance, mass variation and actuator/sensor failure are described in amore specific manner. General active filter has a bad influence on suspension stability. Kalman Filter is based on statistical parameter. Thus, in this paper, It is shown that filtering performance of Kalman Filter and Active filter is excellent with simulation and experiment, stability analyze for air-gap disturbance.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.560-562
• /
• 2002

The liquid crystal(LC) pixel capacitance Clc, which varies as a function of applied pixel voltage, is a main factor of pixel voltage errors on input gamma voltage, and therefore of the electro-optics(E-O) characteristics of LC pixel for a-Si TFT LCDs. The pixel voltage error(${\Delta}$Vp) for input gamma voltage was simulated for 14.1 inch diagonal XGA panel. An agreement between the experimental results and simulation was satisfactory for the gamma voltage compensation, ${\Delta}$Vp of the input gamma voltage. The proposed compensation method was successfully introduced to a 14.1 inch diagonal XGA panel, and a remarkable improvement of image sticking was achived.