• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1448-1452
• /
• 2003

A scratch tester was developed to evaluate the adhesive strength at interface between thin-film and substrate(silicon wafer). Under force control, the scratch tester can measure the normal and the tangential forces simultaneously as the probe tip of the equipment approaches to the interface between thin-film and substrate of wafer. The capacity of each component of force sensor is 0.1 N ${\sim}$ 100 N. In addition, the tester can detect the signal of elastic wave from AE sensor(frequency range of 900 kHz) attached to the probe tip and evaluate the bonding strength of interface. Using the developed scratch tester, the feasibility test was performed to evaluate the adhesive strength of thin-film.

• 한국기계가공학회지
• /
• 제16권3호
• /
• pp.119-124
• /
• 2017

Machining optimization using typical computer-aided manufacturing (CAM) software mainly depends on tool paths, and it is impossible to predict the behavior of material or cutting force. In this paper, cutting force analysis simulation is performed on the Unibody Case of a mobile phone with the aim of optimizing cutting-force-based machining using the Third Wave Systems' AdventEdge Production Module. Machining time after optimization was shortened by 42% for roughing compared to pre-optimization, and actual machining time was reduced by 36.8%. For finishing, machining time was reduced by 92%, and actual machining time was reduced around 90%. A surface roughness analysis found that the post-optimization surface roughness was $1.16{\mu}m$ Ra, compared to a pre-optimization value of $1.75{\mu}m$ Ra.

• Tribology and Lubricants
• /
• 제19권4호
• /
• pp.230-236
• /
• 2003

In applications such as MEMS and NEMS devices, the adhesion force and contact load may be of the same order of magnitude and the static friction coefficient can be very large. Such large coefficient may result in unacceptable and possibly catastrophic adhesion, stiction, friction and wear. To obtain the static friction coefficient of contacting real surfaces without the assumption of an empirical coefficient value, numerical simulations of the contact load, tangential force, and adhesion force are preformed. The surfaces in dry contact are statistically modeled by a collection of spherical asperities with Gaussian height distribution. The asperity micro-contact model utilized in calculation (the ZMC model), considers the transition from elastic deformation to fully plastic flow of the contacting asperity. The force approach of the modified DMT model using the Lennard-Jones attractive potential is applied to characterize the intermolecular forces. The effect of the surface topography on the static friction coefficient is investigated for cases rough, intermediate, smooth, and very smooth, respectively. Results of the static friction coefficient versus the external force are presented for a wide range of plasticity index and surface energy, respectively. Compared with those obtained by the GW and CEB models, the ZMC model is more complete in calculating the static friction coefficient of rough surfaces.

• 한국운동역학회지
• /
• 제20권3호
• /
• pp.319-325
• /
• 2010

The purpose of this research was to investigate the differences in the ski carving turn motion according to level of expertise. The posture and movement of 6 skiers nearby the fall-line was evaluated with a biomechanical approach focusing the rotational mechanics. The slope was at an angle of $9^{\circ}$ and the following variables were measured and calculated: tangential velocity, change of COM height after passing fall-line, width between feet, angle between upper body and thigh, trunk angle, average radius of curvature and average centripetal force. The expert skiers minimized their center of mass height movement and maintained the width of between their feet after the passing the fall-line in comparison with the beginners and intermediate skiers. The experts restrained themselves from pushing their upper body downward after the turn to maximize the centripetal force. The experts in comparison with the beginners and intermediate skiers during the turn didn't have to reduce their radius of curvature to maintain a high centripetal force. It was concluded, that the most important factor affecting the centripetal force, was for the beginners and intermediate skiers, to minimize their movement while using the appropriate amount of edging.

• 한국운동역학회지
• /
• 제27권2호
• /
• pp.117-124
• /
• 2017

Objective: The purpose of this study was to examine the effect of changes in degrees of freedom of the fingers (i.e., the number of the fingers involved in tasks) on the task performance during force production and releasing task. Method: Eight right-handed young men (age: $29.63{\pm}3.02yr$, height: $1.73{\pm}0.04m$, weight: $70.25{\pm}9.05kg$) participated in this study. The subjects were required to press the transducers with three combinations of fingers, including the index-middle (IM), index-middle-ring (IMR), and index-middle-ring-little (IMRL). During the trials, they were instructed to maintain a steady-state level of both normal and tangential forces within the first 5 sec. After the first 5 sec, the subjects were instructed to release the fingers on the transducers as quickly as possible at a self-selected manner within the next 5 sec, resulting in zero force at the end. Customized MATLAB codes (MathWorks Inc., Natick, MA, USA) were written for data analysis. The following variables were quantified: 1) finger force sharing pattern, 2) root mean square error (RMSE) of force to the target force in three axes at the aiming phase, 3) the time duration of the release phase (release time), and 4) the accuracy and precision indexes of the virtual firing position. Results: The RMSE was decreased with the number of fingers increased in both normal and tangential forces at the steady-state phase. The precision index was smaller (more precise) in the IMR condition than in the IM condition, while no significant difference in the accuracy index was observed between the conditions. In addition, no significant difference in release time was found between the conditions. Conclusion: The study provides evidence that the increased number of fingers resulted in better error compensation at the aiming phase and performed a more constant shooting (i.e., smaller precision index). However, the increased number of fingers did not affect the release time, which may influence the consistency of terminal performance. Thus, the number of fingers led to positive results for the current task.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.724-729
• /
• 2007

The study is a structure analysis by applying the output torque and tangential force on 47 ton excavator drive motor gear carrier. The finite element analysis for 3D model is performed by ABAQUS/Standard. We made an estimate by evaluating the results of the finite element analysis.

• 한국정밀공학회지
• /
• 제13권1호
• /
• pp.84-90
• /
• 1996

A theoretical analysis is presented on the mechanics of diamond blade sawing. The normal and tangential components of cutting force are calculated. Experimental results are also presented, which show the effects of cutting variables such as cutting speed, feed speed, cutting area, and concentration of diamond blade on the cutting forces. The experimental results are found to be in good agreement with those predicted by the analytical calculation.

• 반도체디스플레이기술학회지
• /
• 제3권3호
• /
• pp.27-29
• /
• 2004

The responses of hypothetical silicon nanotubes under torsion have been investigated using an atomistic simulation based on the Tersoff potential. A torque, proportional to the deformation within Hooke's law, resulted in the ribbon-like flattened shapes and eventually led to a breaking of hypothetical silicon nanotubes. Each shape change of hypothetical silicon nanotubes corresponded to an abrupt energy change and a singularity in the strain energy curve as a function of the external tangential force, torque, or twisted angle. The dynamics of silicon nanotubes under torsion can be modelled in the continuum elasticity theory.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2004년도 춘계학술대회 발표 논문집
• /
• pp.63-66
• /
• 2004

The responses of hypothetical silicon nanotubes under torsion have been investigated using an atomistic simulation based on the Tersoff potential. A torque, proportional to the deformation within Hooke's law, resulted in the ribbon-like flattened shapes and eventually led to a breaking of hypothetical silicon nanotubes. Each shape change of hypothetical silicon nanotubes corresponded to an abrupt energy change and a singularity in the strain energy curve as a function of the external tangential force, torque, or twisted angle. The dynamics of silicon nanotubes under torsion can be modelled in the continuum elasticity theory.

• 한국소음진동공학회논문집
• /
• 제26권6_spc호
• /
• pp.635-643
• /
• 2016

안정성 지도(stability map)을 이용하여 부분 종동력(sub-tangentailly follower force)를 받는 외팔 기둥의 동적안정성 이론을 요약한다. Rayleigh 감쇠를 가정하여 내적 및 외적 감쇠효과를 2개의 감쇠비를 통하여 반영하고, 감쇠비 변화에 따른 플러터하중의 변화와 관련된 매개변수 연구를 수행한다. 또한, 종동력을 받는 외팔기둥에 대한 진동수 방정식의 엄밀해를 유도하고, 특정 감쇠비 범위에 대한 안정성 지도를 유한요소 해석결과와 함께 비교/분석한다.