• Journal of Welding and Joining
• /
• 제16권1호
• /
• pp.77-87
• /
• 1998

This paper deals with the effect of laser welding parameters on the weld formation. Thin steels for automotive application were prepared so as to be welded with high power carbon dioxide laser system. Major process parameters were position of focus and travel speed. The effect of shielding gas was also discussed by employing the high speed photometry. Test results showed that the optimal position of focus varied in accordance with the joint configuration; bead-on-plate, butt or lap welding. It was recommended that the position of focus for the lap welding be located at slightly inner part of the material to be welded. In this case, however, it was noticeable that the weld penetration ratio, d/t$_{0}$ dropped drastically at the critical region. Results also demonstrated that both the bead width and penetration reduced as the travel speed increased. The penetration ratio showed two distinct regions; stabilized zone at the lower range of the travel spped and sudden drop zone at the higher range of travel speed. Lower limit of the penetration for acceptable weld was proved to be about 90% of the parent metal thickness based on the physical properties of the weld. Mixed gas application for both the shielding of molten metal and laser induced plasma control was recommended as far as the penetration was concerned.d.

• 소성∙가공
• /
• 제8권1호
• /
• pp.7-13
• /
• 1999

In this study, side panels were developed using the laser-welded tailored blank (T.B.) of both the same thickness and different thickness. At first, the formability of the same thickness T.B. was investigated to compare with one of the non-welded panel with respect to weldline movement and strain distribution in blank during the stamping process. Based on these results, we determined the weld line positions and the die step for T.B. forming of the blanks composed of different thickness combination. Then we made some stamping tryouts with selected types of blanks to investigate the formability of T.B. of the different thickness. During the tryouts, wrinkles were found in the a-pillar lower region which is under the deformation mode of the shrink flange. In the b-pillar region, fractures were also found. These defects have been reduced and corrected by controlling the blank design, the die faces and process parameters.

• 소성∙가공
• /
• 제9권6호
• /
• pp.582-589
• /
• 2000

In recent automotive industry, vehicle weight can be reduced by one-step forming of tailored blanks welded with two or more sheets of metal blanks. Mash seam welding shows an overlap joint, a much wider welding area, and heat affected zone(HAZ) than a laser welding. This paper deals with the forming characteristics of mash seam welded tailored blanks. Mash seam welded blanks of same or different thickness combinations were prepared, and tensile, hardness, erichsen, and dome stretching tests were done.

• Journal of Welding and Joining
• /
• 제17권2호
• /
• pp.66-75
• /
• 1999

Weld bead quality in tailored blank(TB) is critically affected by edge preparation of sheets. The edge quality of prepared sheets for TB can be classified into straightness and the cross section quality of sheared plane such as a ratio of shear face, shear plane angle, etc. In order to have a good edg quality for butt-welding sheets, precision shearing will be recommended. In this paper, the feasibility of a conventional mechanical shearing as the edge preparation for tailored blanks is studyied. It reveals that fine shearing may not be the unique solution as it is generally accepted. To obtain the good shearing condition with a conventional mechanical shearing, experiments were carried out using Tahuchi method. The major parameters affecting a sheared contour are the clearance between upper blade and lower blade, and shear angle. The optimal shearing condition yields a very good straightness along the entire length of the cut, which gives a butt joint gap less than 10% of the base material thickness. The good cross section of sheared plane is also achieved in the optimal shearing condition such as a ratio of the shear face above 65%, a cross section's shear plane angle above 85%, little burr, which is providing finally good weld beads.

• 한국레이저가공학회지
• /
• 제17권2호
• /
• pp.11-18
• /
• 2014

This research was conducted as a fundamental study to apply tailored blank welding technique into automotive production process. Specially we tried to apply the TWB technique to exhaust system. The materials used in this work were ferritic 439 stainless steel sheet with a thickness of 1.2mm and 0.8mm. Welding tests were conducted for BOP test and dissimilar thickness (0.8 to 1.2t) cases. Major process parameters were position of focus, travel speed, shielding gas and joint (gap) condition. As a result, there are nothing significant welding characteristic compare with TWB of carbon steel. Stainless steel shows the good weldability and mechanical properties (tensile, hardness and forming strength) also shows high level. Just problem is gap condition. However, also in this case, it shows not only good forming strength but also base metal fracture after tensile test. And to conclude, it is good opportunity to make lightweight design muffler using TB welding technique.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.21-23
• /
• 2003

• 한국레이저가공학회지
• /
• 제3권2호
• /
• pp.53-61
• /
• 2000

On the laser weld production line, a slight alteration of the welding condition produces many defects. The defects are monitored in real time, in order to prevent continuous occurrence of defects, reduce the loss of material, and guarantee good quality. The measurement system is produced by using three photo-diodes for detection of the plasma and spatter signal in CO$_2$ laser welding. For high speed CO$_2$ laser welding, laser tailored welded blanks for example, on-line weld quality monitoring system was developed by using fuzzy multi-feature pattern recognition. Weld qualities were classified optimal heat input, a little low heat input, low heat input, and focus misalignment, and final weld quality were classified good and bad.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2000년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.307-309
• /
• 2000

• 한국레이저가공학회지
• /
• 제5권2호
• /
• pp.23-29
• /
• 2002

As automotive manufacturers have taken a growing more interest in tailored sheet metals for improving the rigidity, weight reduction, crash durability, and cost saving application of the tailored sheet metals to automotive bodies has been resently increased greatly. In this study, we investigated the characteristics of fatigue crack initiation behavior of laser welded sheet use for vehicle body panel. We experimented three types of specimens which were machined of the same base metal : one is 1.4㎜ thick, another is 1.6㎜ thick, the others is laser welded of the 1.4mm thick specimen and 1.6㎜ thick specimen. The results indicated that laser welded metal (1.4＋1.6㎜) is the best one for fatigue strength and fatigue life.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.55-58
• /
• 1997

In automotive industries, stamping of laser-welded blank gives many merits which brings about dimensional accuracy, strong body assembly and high productivity. However the welding of blanks with different thickness or/and different strength materials introduces many challenging formability problems for process development and tool design. In this paper, the deformation characteristics for deep drawing process of laser-welded blank with different thickness sheets are investigated by experiment and FEM simulation. And also the optimal location of weld line in laser-welded blank with different thickness sheets is calculated to compensate for the movement of weld line on deep drawing process. In addition, the effect of location of weld line is clarified using FEM simulation.