• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.7
• /
• pp.595-601
• /
• 2009

For the silicon oxide $(SiO_x)$ films prepared by using the facing target sputtering (FTS) apparatus that was manufactured to enhance the preciseness of the fabricated thin-film and sputtering yield rate by forming a higher-density plasma in the electrical discharge space for using it as a thin-film passivation system for flexible organic light emitting devices (FOLEDs). The deposition characteristics were investigated under various process conditions, such as array of the cathode magnets, oxygen concentration$(O_2/Ar+O_2)$ introduced during deposition, and variations of distance between two targets and working pressure. We report that the optimum conditions for our FTS apparatus for the deposition of the $SiO_x$ films are as follows: $d_{TS}\;and\;d_{TT}$ are 90mm and 120mm, respectively and the maximum deposition rate is obtained under a gas pressure of 2 mTorr with an oxygen concentration of 3.3%. Under this optimum conditions, it was found that the $SiO_x$ film was grown with a very high deposition rate of $250{\AA}$/min by rf-power of $4.4W/cm^2$, which was significantly enhanced as compared with a deposition rate (${\sim}55{\AA})$/min) of the conventional sputtering system. We also reported that the FTS system is a suitable method for the high speed and the low temperature deposition, the plasma free deposition, and the mass-production.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.12
• /
• pp.89-100
• /
• 1997

This paper investigated a new type of low voltage threshold switch (LVTS). As distinguished from the many other types of electronic threshold switches, the LvTS is ; voltage controlled, occurs at low voltages ($V_{2}$ $O_{5}$lV devices. The average low threshold voltage < $V_{LVT}$>=218 mV (standard deviation =24mV~kT/q, where T=300K), and was independent of the device area (x100) and amorphous oxide occurred in an ~22.angs. thick interphase of the V/amorphous- $V_{2}$ $O_{5}$ contacts. At $V_{LVT}$ there was a transition from an initially low conductance (OFF) state into a succession of quantized states of higher conductance (ON). The OFF state was spatically homogeneous and dominated by tunneling into the interphase. The ON state conductances were consistent with the quantized conductances of ballistic transport through a one dimensional, quantum point contact. The temeprature dependence of $V_{LVT}$, and fit of the material parameters (dielectric function, barrier energy, conductivity) to the data, showed that transport in the OFF and ON states occurred in an interphase with the characteristics of, respectively, semiconducting and metallic V $O_{2}$. The experimental results suggest that the LVTS is likely to be observed in interphases produced by a critical event associated with an inelastic transfer of energy.rgy.y.rgy.

• Journal of the Korean Chemical Society
• /
• v.53 no.5
• /
• pp.499-504
• /
• 2009

Metals have often played important roles to some enzymatic reactions that are essential to biological processes. Therefore many scientists have studied the reaction mechanisms of catalytic reactions in metaloenzymes for many years. Methane MonoOxygenase (MMO) is an enzyme that oxidize methane to methyl alcohol. Recently Tolman et al. studied a model reaction for MMO, which is a hydroxide transfer reaction in Bis-($\mu$-oxo)-dicopper complex, and suggested several possible mechanisms. Later a two-step mechanism, which is hydrogen transfer followed by hydroxide rebound, was proposed from theoretical studies. In this study we calculated the reactant, product, and the transition state structures, and energetics of the first hydrogen transfer reaction using various DFT methods including recently developed the MO6 family of DFT, namely, MO6, MO6L, and MO6-2X. We found that the M06/6-31G(d,p)/LANL2DZ method reproduce the experimental XRD structure of reactants very well. The TS structures, barrier heights, and reaction energies depend very much on the size of the basis sets.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.261-262
• /
• 2006

High temperature superconducting coated conductor has multi-layer structure of protecting layer/superconducting layer/buffer layer/metallic substrate. The buffer layer consists of multi layer, and the architecture most widely used in RABiTS approach is $CeO_2$(cap layer)/YSZ(diffusion barrier layer)/$CeO_2$(seed layer). Multi-buffer layer deposition required many times and process. Therefore single buffer layer deposition study reduce 2G HTS manufacture efforts. Evaporation technique for single buffer deposition method is used for the $CeO_2$ layer. $CeO_2$ single buffer film could be achieved in the chamber. Detailed deposition conditions (temperature and partial gas pressure of deposition) were investigated for the rapid growth of high quality $CeO_2$ single buffer film.

• Korean Journal of Food Science and Technology
• /
• v.30 no.6
• /
• pp.1381-1387
• /
• 1998

Laminated films were prepared by casting corn-zein and fatty acid mixed solutions onto ${\kappa}-carrageenan$ films, and the effect of various fatty acids with different concentrations on the film properties such as water vapor permeabilities (WVP), tensile strength (TS) and elongation was investigated. WVP of the film decreased as concentration of fatty acids increased, and the lowest WVP value $(0.497\;ng\;m/m^2\;s\;Pa)$ was achieved with laminated films containing 30% lauric acid/corn-zein. The TS of laminated edible film seemed to decrease as the concentration of fatty acids increased, and TS of the laminated film was the highest (36.21 MPa) when the film contained 10% oleic acid. Weight loss of the minced mackerels packaged with corn-zein/carrageenan film which did not contain fatty acid was 11.7%, but weight losses of the samples packaged with oleic acid and lauric acid were 6.97% and 0.81%, respectively, after 30 days storage at $-20^{\circ}C$. The laminated films had an effect on preventing oxidation of the minced mackerels during storage because of high oxygen barrier property of the film. All of the minced mackerels packaged with the laminated films greatly reduced the peroxide value (POV) compared with unpackaged minced mackerels during storage. Also, thiobarbituric acid (TBA) values of the minced mackerels packaged with the laminated films were lower than that of unpackaged minced mackerels during storage.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.3
• /
• pp.44-55
• /
• 1987

In order to study the effect of sawdustboard combined with plastic chips, 0.5mm($T_1$), 1mm($T_2$), 1.4mm($T_3$) thick nylon fiber. polypropylene rope fiber(RP), and 0.23mm thick moth-proof polypropylene net fiber(NP) were cut into 0.5, 1, 2cm long plastic chips. Thereafter, sawdustboard combined with plastic chips prepared as the above and plastic non-combined sawdustboard(control) were manufactured into 3 types of one-, two-, and three layer with 5 or 10% combination level. By the discussions and results at this study, the significant conclusions of mechanical and physical properties were summarized as follows: 1. The MORs were shown in the order of 3 layer> 2 layer> 1 layer among plastic non-combined boards, and $T_3$ < $T_2$ < $T_1$ < RP (NP(5%) < NP(l0%) among plastic combined boards. In 2cm long plastic chip in 1 layer board, the highest strength through all the composition was recognized. 1 layer board showing the lower strength with 0.5cm plastic chip rendered to the bending strength improvement by 2 or 3 layer board composition. On the other hand, 2 or 3 layer combined with 1, 2cm long polypropylene net fiber chips incurred MOR's conspicuous decrease requiring optimum plastic chip combined level and consideration to combined type. 2. MOE in plastic non-combined 3 layer board exhibited sandwich construction effect by higher resin content application to surface layer in the order of 3layer>1layer>2layer with the highest stiffness of the board combined with polypropylene chip, while nylon chip-combined board had little difference from plastic non-combined board. In relevant to length and layer effect, 3 layer board combined with the 0.5cm long polypropylene net fiber chip in 5% and 10% combined level presented 34-43% and 44-76% stiffness increase against plastic non-combined board(control), respectively. Moreover, in 1 layer board, 30% stiffness increase with 10% against 5% combined level in the 1 and 2cm long polypropylene net fiber chip was obtained. 3. Stress at proportional limit(Spl) showing the fiber relationship (r: 0.81-0.97) between MOR presented in the order of 1 layer<2 layer<3 layer in plastic non-combined board. Correspondingly, combined effect by layer and plastic chip length was similar to MOR's. 4. Differently from previous properties(MOR, MOE, Spl). work to maximum load(Wml) of 2 layer board approached to that of 3 layer board. Conforming the above phenomenon. 2 layer combined with 0.5cm long polypropylene net fiber chip kept the greater work than 1 layer. The polypropylene combined board superior to nylon -and plastic non - combined board seemed to have greater anti - failing capacity. 5. Internal bond strength(IB), in contrast to MOR's tendency. showed in the order of T1