• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.539-539
• /
• 2012

전북대학교 고온플라즈마 응용연구센터는 교육과학기술부 기초연구사업 중 고가연구장비 구축사업의 일환으로, 고 엔탈피, 초음속 유동 환경을 모사하여, 항공우주, 군사기기, 핵융합 분야 등의 고온 재료 개발을 위한 기초 연구 장치로써, 0.4MW급 플라즈마 풍동 장치를 구축하고 있다. 0.4MW 플라즈마 풍동 장치의 플라즈마 발생부는 DC 전원 공급장치와 디스크 형태의 양극과 음극 사이에 동일 형태의 간극을 삽입한 0.4MW급 분절형 아크 플라즈마 토치로 구성되었으며, 토치에서 발생된 아크 플라즈마는 노즐을 통과하며 마하 2~4의 초음속을 나타내도록 설계 제작되었다. 시험 챔버는 노즐에서 나온 초음속 플라즈마의 특성 및 재료 시험을 위한 3차원 이송식 기판이 장착되어 있으며, 고 엔탈피 유동을 관측하기 위한 광학창을 구비하였다. 시험 챔버 하류에는 유동 안정을 위한 디퓨저(diffuser)가 설치되어 있으며, 디퓨저(diffuser)로부터 배출되는 고온가스는 열교환기를 통해 냉각된 후 진공펌프를 통해 대기로 배출되게 된다. 장치의 압력조절을 위하여 $1,000m^3/min$의 용량의 진공펌프 시스템이 설치될 예정이며 가스공급장치, 냉각수 공급장치, 디퓨져, 열교환기는 1MW급 용량으로 설계 제작되었다. 본 장치는 400kW의 전원 공급, 15 g/s의 공기유량 주입 시 약 13 MJ/kg의 고엔탈피를 가진, mach 2~4의 초음속 유동을 나타내는 것을 특징으로 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.190-190
• /
• 2012

전북대학교 고온 플라즈마 응용 연구 센터는 교육과학기술부 기초연구사업 중 고가연구장비 구축사업의 일환으로 소재공정용 다목적 100 kW 플라즈마 발생장치를 구축하고 있다. 100kW급 ICP (RF)형 플라즈마 발생장치는 RF 전력 인출이 이중으로 되어있어 한쪽에서는 수~수십 um 크기의 금속, 세라믹 등 고융점 원료분말을 순간적으로 용해, 기화 및 분해시키고 이들 기화 또는 분해된 증기를 급랭시키는 과정에서 초미분(<1 um)을 합성하는 플라즈마 합성법 연구가 가능하도록 RF 플라즈마 분말 합성 시스템이 연결되어 있고 다른 한쪽으로는 진공 챔버 내에서 고온 고속의 RF 플라즈마 불꽃을 형성 한 후 RF 플라즈마의 축 방향으로 반응성 가스 및 코팅 대상 물질을 주입하여 코팅 할 수 있는 열플라즈마 용사코팅 시스템이 연결되어 있는 다목적 연구 장치이다. 본 장치는 100 kW급 RF 전원 공급기와 유도결합형 플라즈마 토치, 플라즈마 분말 합성 부, 플라즈마 코팅 및 반응성 증착부, 가스 공급부, 냉각수 공급부, 전기 계장/제어부로 구성되어 있다.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.57-65
• /
• 1997

A study was undertaken to determine the influence of welding variables such as shielding and plasma gases, torch standoff, travel speed and heat input, etc. on the quality of plasma arc welds in Zircaloy-4 sheet, 2mm thick. Effect of shielding gases and their flow rates on the mechanical properties of Zircaloy-4 welds by plasma arc welding were determined in terms of tensile, bardness and bend tests. The microstructure and fracture surface of Zircaloy-4 welds were investigated by optical and scanning electron microscopies. In addition, the causes of porosity and undercut in plasma arc welds of Zircaloy-4 were also investigated. Zircaloy-4 weld bead width and depth by helium shielding gas showed a wider and deeper than those by argon. It was found that Zircaloy-4 welds with shielding gas of helium did dxhibit a little smoother and uniform weld beads than those with shielding gas of argon. It was also found that the optimum gas flow rates for Zircaloy-4 welding were 0.45l/min for plasma gas with Ar and 4.5 - 6 l/min for shielding gas with He. In addition, there was no big difference in the microstructure and fracture surface of the weld metals made by either Ar shielding gas or He shielding gas.

• Journal of Welding and Joining
• /
• v.18 no.5
• /
• pp.98-104
• /
• 2000

Aluminum alloys are being employed in automobile parts as strive to reduce overall vehicle weight to meet demands for improved fuel economy and reduction in vehicle emissions. Al-based composites reinforced with ceramic ($Al_2O_3,\;SiC,\;TiC\;and\;B_4C$) applications in a variety of components in automotive engines, such as liners, where the tribological properties of the material are important. In this study, Al-base composites reinforced with TiC particle powders has been developed for producing plasma spray coatings. The composite plasma spray powders were prepared Al-13Si-3Mg(wt%) alloy with TiC(40, 60 and 80wt%) particles ($0.2~5{\mu}textrm{m}$) by drum type ball milling. The composite powders ($36~76{\mu}textrm{m}$) were sprayed with plasma torch. Plasma sprayed coatings were heat-treated at $500^{\circ}C$ for 3 hours. The wear resistances of the plasma sprayed coatings were found to decrease with increasing TiC content and improved with heat treatment. AlSiMg-40% TiC heat-treated coatings were showed the best wear resistance in this study.

• Journal of Welding and Joining
• /
• v.10 no.2
• /
• pp.51-62
• /
• 1992

A torch was designed and fabricated in order to develope the technology of "locally drying underwater welding" by water curtain method. The condition for the formation of the possible local cavity, the mechanical properties and the thermal cycle of welds were investigated in the developed welding equipment compared with in-air welding. The possibility of highly reliable and practical underwater welding was found. The proper local cavity was formed above the water flowrate of 30l/min and CO$_{2}$ gas flowrate of 100l/min. The bead width and penetration depth were increased with increasing welding current. The hardness of weldments is about 160Hv in air welding, but about 210Hv in underwater welding. The elongation and the impact value of underwater weldments are 15% and 6Kg/cm$^{2}$ respectively, which are only half as much as the values of in-air welding. The cooling time in the temperature range from 800.deg.C to 500.deg.C affecting the structure and the hardness of weldments is about 22sec. in air welding while about 10sec. in underwater welding.r welding.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.6
• /
• pp.619-630
• /
• 2014

Two butanol-based Condensation Particle Counters (CPC 3022, CPC 3025), three water-based CPCs (CPC3781, CPC3785${\times}$2), a Gardner Counter, a Fast Mobility Particle Sizer (FMPS), and an Aerosol Electrometer (AE) were deployed to measure the number concentrations from atomized aerosol under six different conditions. Comparisons of particle number concentrations measured by the CPCs, FMPS, and AE were conducted to evaluate the performance of the each CPCs using laboratory generated artificial particles such as NaCl, succinic acid ($C_4H_6O_4$), and particles generated by propane torch & heat gun in the chamber. Good correlation between the CPC3025 and FMPS was observed for the total particle number concentrations in the size range 15 nm to 90 nm. In addition, this paper suggests that photometric mode in water-based CPC3785 could not be used as quantitative of number concentrations for CPC3785.

• Journal of the Korean institute of surface engineering
• /
• v.31 no.2
• /
• pp.81-90
• /
• 1998

NiCrAly/YSZ(8wt% Y2O3-Zro2) functionally fraded thermal barrier coating (FGC) layers on a Co-base sureralloy (HAYNESS 188) substrate were fabricated using Ar shielded single torch air plasma spraying method. Functional grading were produced with the stepwise compositional change throughout layer thinkness. Microstructural observation revealed a sucessful fabrication of NiCrAly/YSZ FGC. From the results of the curvature measurement, adhesive stength measurement and thermal shock test for the FGC, it was concluded that the optimum enhance of functionally graded coating layer thinkcess and compositional pattern exit to enhance the properties of FGC, which is closely reated to the internal residual distribution with it.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.3
• /
• pp.241-248
• /
• 2005

The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters compared with the heating by torch. In this study, a more efficient method was proposed for the prediction of plate bending. The existing analysis method using the axi-symmetric coil model could not handle the varying temperature during the heating and the forming process for curved plates like a saddle or a concave type curvature. The proposed method using some discrete steps in this study could overcome these difficulties and show more accurate, reasonable results in temperatures and deflections of fiat or curved plates. This method is composed of multi-disciplinary analyses such as an electro-magnetic analysis, a heat transfer analysis and a deformation analysis based on inherent strain approach.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.10
• /
• pp.1051-1056
• /
• 2014

In this paper, we introduce an intelligent robotic arc welding system which exploits sensors like as LVS (Laser Vision Sensor), Hall effect sensor, voltmeter and so on. The use of industrial robot is saturated because of its own limitation, and one of the major limitations is that industrial robot cannot recognize the environment. Lately, sensor-based environmental awareness research of the industrial robot is performed actively to overcome such limitation, and it can expand application field and improve productivity. We classify the sensor-based intelligent arc welding robot system by the goal and the sensing data. The goals can be categorized into detection of a welding start point, tracking of a welding line and correction of a torch deformation. The Sensing data can be categorized into welding data (i.e. current, voltage and short circuit detection) and displacement data (i.e. distance, position). This paper covers not only the explanation of the each category but also its advantage and limitation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.55-60
• /
• 1981

Some physical properties of Ni-Cr based alloy for porcelain veneering were compared after repeated casting without the addition of any new alloy. The specimen were cast in a centrifugal caster with an oxygen-propane torch at optimum temperature. The obtained results were as follows: 1. The yield strength and hardness of the second generation were no significant differences compared with first generation but the yield strength and hardness of the third generation slightly decrased. 2. The ultimate tensile strength and elongation appeared to decrease slightly in second, third generations. 3. The tensile fractured facets of the first generation specimen were normal in all specimen, but in the second generation there were six tensile specimen out of ten, in the third there were four tensile specimen out of ten.