• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.948-951
• /
• 2005

New technology that reduces photolithography process steps from 4 to 3 in fabrication of TFT LCD is introduced. The core technology for 3mask-TFTs is the lift-off process [1], by which the PAS and PXL layer are formed simultaneously. To evaluate the stability of this lift-off process, outgases from photo resist on a substrate during ITO deposition and the quality of ITO film were analyzed and the conventional photo resist stripper machine which operates lift-off process was examined to see its ability to reduce particle problems of the machine. Through the development of total process and design for TFTs using this 3mask technology, panels in TN and IPS modes which exhibit same performances of a display using a conventional process were achieved. In addition, this process was already verified in the mass production line and now some products are being produced by the 3mask technology.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 디스플레이 광소자분야
• /
• pp.210-213
• /
• 2004

We synthesized photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the photopolymer surface can be obtained. However, the low pretilt angles were obtained below $1^{\circ}$. The Voltage-transmittance (V-T) curve without backflow bounce in the photoaligned TN cell with UV exposure was observed. The response time of photoaligned TN cell was measured about 24 ms. Finally, The photoaligned TN cell has few hysteresis, and shows the residual DC voltage that is less.

• 한국위성정보통신학회논문지
• /
• 제7권3호
• /
• pp.145-148
• /
• 2012

최근의 TV용 TFT-LCD에서는 동화상에서의 잔상발생을 줄이는 것이 중요한 기술적 요구사항이 되었다. Single-LVDS 신호체계에서 3D를 대응하기 위한 Quad Signal Package 까지 진화하면서 보다 빠른 신호를 정해진 시간안에 처리해야 하는 문제가 발생하고 있으며, 이러한 특성을 구현하기 위해서 잔상효과가 없는 Backlight에 대한 연구가 활발히 진행되고 있다. 본 연구에서는 점멸방식의 Backlight 를 사용하여, 1Frame의 시간안에 이 동작이 가능하게 구현하는 것을 목표로 삼았으며, 광원으로는 기존의 냉음극관램프를 사용하였다. 통상 냉음극관램프는 주 발광파장대를 담당하는 녹색의 잔광시간이 길어서 위와 같은 특성을 구현하기에 어려움이 있었으나, 본 연구에서는 단잔광 특성을 가지는 녹색 및 적색 형광체를 적용한 냉음극관램프를 적용하여, 1Video Frame의 시간안에 점멸동작이 가능한 백라이트를 제작하였으며, 이를 사용하여, 동화상에서 비약적인 잔상 해결 효과를 확인할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제35권1호
• /
• pp.58-65
• /
• 2022

The field of liquid crystal display (LCD) is constantly in the spotlight and the process of depositing an alignment layer in the LCD manufacturing process is very important to obtain excellent performance such as low-power driving and high-speed response to improve LCD performance. Therefore, research on liquid crystal (LC) alignment is being actively conducted. When manufacturing LCD, it is necessary to consider the effect of the alignment layer thickness as one of the factors affecting various LCD performances. In addition, previous studies confirmed the LC alignment characteristics correlate with the rotation speed in the spin coating process. Therefore, the electro-optical properties of the LCD were investigated by manufacturing a polyimide alignment layer by varying the rotation speed in the spin coating process in this study. It was confirmed that the thickness of the polyimide alignment layer was controlled according to the spin coating conditions. The average transmittances of anti-parallel LC cells at the spin coating speed of 2,500 rpm and 3,000 rpm are about 60%, which indicates that the LC cell has relatively higher performance. At the spin coating speed of 3,000 rpm, the voltage-transmittance curve of twisted nematic (TN) LC cell was below 1.5 V, which means that the TN LC cell operated at a low power. In addition, high-speed operating characteristics were confirmed with a response time of less than 30 ms. From these derived data, we confirmed that the ideal spin coating speed is 3,000 rpm. And these results provide an optimized polyimide alignment layer process when considering enhanced future LCD manufacturing.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.914-917
• /
• 2002

We have obtained high performance and low voltage driving OCB panel by reducing the critical voltage and retardation matching between liquid crystal layer and compensation films. The critical voltage in the panel has been minimized by flattening color filter layer and optimizing a rubbing process. In addition, an appropriate retardation of the film and LC layer has scanned to achieve low driving voltage and high transmission. The proto-type 17" WXGA OCB panel has demonstrated with less than 5V drive and over 80 degree for all viewing direction except for rubbing direction with over 90% of TN light efficiency.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.457-459
• /
• 2005

Low viscosity LCs have been developed for fast response time improvement of the TFT-LCD Monitors based on TN mode. This low viscosity characteristic s cause the pretilt angle to be changed and the uniformity to degrade. We have studied on the pretilt angle effect by the various components used for low viscosity LCs. We prepared the panels by using these various components and measured pretilt angle for this research. As a result of this research, we have found out that each low viscosity component has the different pretilt angle level and uniformity. For good display quality, it is important to keep the stable pretilt angle. The low viscosity LCs with this stable pretilt angle make it possible to prepare the high performance TFT-LCD Monitor with both fast response time characteristics and good display quality

• 한국전기전자재료학회논문지
• /
• 제18권10호
• /
• pp.924-928
• /
• 2005

We synthesized the two types of photoalignment material of high thermal resistance with hydroxyl aromatic polyimide, and studied the liquid crystal (LC) aligning capabilities on the photopolymer layers. Also, electro-optical (EO) performances for the twisted-nematic (TN)-liquid crystal display (LCD) photoaligned with linearly polarized UV exposure were investigated. A good LC alignment with UV exposure on the two types of photopolymer surface can be obtained. The Voltage-transmittance (V-T) curve in the photoaligned TN cell with UV exposure was different from two type. The response time of photoaligned TN cell was measured about 21 ms in two alkyl chain and about 15 ms in four alkyl chain.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1462-1465
• /
• 2009

Because of its weak points that narrow viewing angle and grayscale inversion, 'bare' twisted nematic (TN) LCD has some limits to use as a display device, though its great strong points that low cost, high yield, simple design, high transmittance and normally white. The 'WideView(WV)' film which introduced by Fuji co., has been good solution to extend the viewing angles of TN mode, therefore that film have been used generally for TN panels needed wide viewing angle. This paper introduce the research to find the parameters of the Wide view film and a TN panel which affect viewing angle characteristics and how to adjust those parameters.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.400-400
• /
• 2007

In this study, we investigated liquid crystal (LC) alignment with ion beam (IB) that non contact alignment technique on polyimide and electro-optical characteristics of twisted nematic (TN)-liquid crystal display (LCD) on the polyimide under various ion beam angles. In this experiment, polyimide layer was coated on glass by spin-coating and Voltage-transmittance(VT) and response time characteristics of the TN cell were measured by a LCD evaluation system. The good characteristics of the nematic liquid crystal (NLC) alignment with the ion beam exposured polyimide surface was observed. In addition, it can be achieved the good EO properties, and residual DC property of the ion beam aligned TN cell on polyimide surface.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.1125-1131
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on the two kinds of polyimide (PI) surfaces using thin plastic substrates. The NLC pretilt angles generated on thin plastic substrates are higher than that on the glass substrate. We study that AFM (atomic force microscope) image of rubbed PI surface with polymer film has formed the micro-groove. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass.