• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 1999.11a
• /
• pp.180-186
• /
• 1999

Alkaline peroxide bleaching of (chemi) mechanical pulp is a very complicated system where various process factors affect the bleaching performance and pulp properties. Traditional on-factor-at a time method is ineffective and costly in finding the optimal bleaching conditions. In this study statistical experimental methods which include three steps. I. e. screening, response surface modeling and optimization, were used to find the conditions for maximal brightness development during one stage alkaline peroxide bleaching of TMP which had an initial brightness of 54.5% Elerpho. The TMP was pretreated with EDTA(0.5% on O. D. pulp. consistency, $30^{\circ}C$ for 60 minutes) and bleached in a 2L Mark V Quantum Reactor at 750rpm, 7.5% of bleaching consistency and with 0.05% magnesium sulfate addition. The ranges of other factors studied were 1~5% hydrogen peroxide on O. D plup, 1~4% sodium hydroxide on O. D pulp and 1~4% sodium silicate on O. D pulp, reaction temperature 50~$90^{\circ}C$ and reaction time 40~180minutes. A models with good predictability was established and the maximal brightness after one stage bleaching was found to be 70% Elerpho at $50^{\circ}C$, 50 minutes 5% hydrogen peroxide on O. D. pulp 3.2~3.4% sodium hydroxide on O. D. pulp 3.2~3.4% sodium hydroxide on O. D pulp and 4% silicate on O. D pulp. However further studies on other pulp properties such as strength and brightness stability shall be carried out in order to find out the optimal bleaching conditions.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.2
• /
• pp.35-45
• /
• 2014

Confocal Reflection Microscopy (CRM) was applied to investigate external fibrillation of different types of fibers such as Kajaani reference fiber, Whatman filter fiber, thermomechanical pulp (TMP), and recycled TMP fiber. It was confirmed that the CRM images are created from surface structures of the fiber cell wall. Confocal Laser Scanning Microscopy (CLSM) captured overall shape of the fiber, but minute details of the surface of the fiber were missed. CRM captured the minute details of the fiber surface. From the CRM and CLSM images, it was observed that the CRM images mainly appeared on the fiber surfaces. External fibrillation of the fiber occurs at the fiber surface, not inside the cell wall. Thus, it was concluded that investigation on the external fibrillation of the fiber was possible by utilizing CRM images. A direct qualtitative and quantitative method for analysis of external fibrillation of fiber was demonstrated by utilizing surface area to volume ratio, volume fraction, and roughness calculated from 3-dimensional images reconstructed from stacks of CRM images from the different fibers.

• Journal of Biosystems Engineering
• /
• v.30 no.5 s.112
• /
• pp.285-292
• /
• 2005

Extrusion process and physical properties of extrudates of pulp powder (TMP, thermomechanical pulp fibers) mixed with expanding additives was evaluated to develop biodegradable packaging materials. To find out the optimum condition, the status of extrusion process, coefficient of elastic and expansion ratio of extrudates were tested on the composites (wheat flour, soluble starch, polyvinyl alcohol), blending conditions of composites and moisture contents of extrudates. In case of material composition, wheat flour played a key role to keep extrusion process irrespective of the added amounts of soluble starch and polyvinyl alcohol. The coefficient of elastic of extrudates was increased and the expansion ratio was reduced as the added amounts of wheat flour increased. Also, the coefficient of elastic of extrudates was decreased as the moisture content of extrudates increased. The lowest coefficient of elastic was 439.55 kPa under the condition, of pulp powder mixed with $20\%$ of wheat flour based on pulp weight and $10\%$ of soluble starch based on wheat flour weight and controlled $20\%$(wb) of moisture content.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.112-119
• /
• 2015

The pulp mold attract the increasing concern as recyclable, biodegradable, and eco-friendly packaging materials. In order to broaden the applicability of the pulp mold as substitutes of the expanded styrofoam, the properties of various raw materials for the pulp mold were evaluated and the way for improving water resistance properties of the pulp mold were also tested by applying some additives. The higher value in the fines contents and in the water retention value were shown for the TMP (thermomechanical pulp), which resulted in the bulkier pulp mold with the higher moisture absorption property. In case of water resistance properties, the pulp mold made of white ledger stock showed the higher value in water contact angle and very slow water absorption rate. The addition of oil palm EFB fiber showed the improvement in the water resistance of the pulp mold made of UBKP. The effects of various additives on the improvement in the water resistance properties of the pulp mold were tested by using AKD, PVAm, epoxy resin. The application of AKD leaded to the higher increase in the water resistance. The results in this study showed the effects of AKD for the pulp mold could be improved and optimized by the application with fixing agent and by the ageing treatment after production.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.100-110
• /
• 2016

Alkaline Peroxide Mechanical Pulping (APMP) of Pinus densiflora harvested from domestic mountains was explored. APMP contributes to various advantages including pulp quality, elimination of the need for a bleaching process, and energy savings. Sequential treatment of impregnation of bleaching chemicals and refining not only overcome the concern of alkaline darkening of wood chips during chemical impregnation, but it also brightens the chips to the desired brightness levels suitable for writing and printing papers. APMP pulping from Pinus densiflora was greatly influenced by the dosage levels of hydrogen peroxide and sodium hydroxide. Alkaline peroxide treatment was carried out by applying one of three levels of hydrogen peroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips) and one of three levels of sodium hydroxide (1.5, 3, and 4.5% based on the oven-dried weight of the wood chips). Other chemicals including a peroxide stabilizers and metal chelation were constantly added for all treatments. Chemical treatment with a liquor-to-wood ration of 9:1 was carried out in a laboratory digestor. Compared to BTMP, APMP pulping displayed outstanding characteristics including the less requirement of refining energy, the better improvement of tensile strength, the more reduction of shives, and the greater increase of pulp brightness. In particular, when 4.5% of hydrogen peroxide with impregnation during 90 minutes was used, the brightness of APMP reached 64.9% ISO. Even though bulk of APMP was decreased with the increase of sodium hydroxide, a better and improved balance could be achieved between optical and strength properties. The spent liquor obtained from the discharge of the impregnation process at the dosage level of 4.5% hydrogen peroxide exhibited an equal level of residual peroxide with BTMP. In conclusion, APMP pulping showed successful results with Pinus densiflora due to its better response to the development of optical and physical properties compared to TMP pulping.