• 비파괴검사학회지
• /
• 제7권2호
• /
• pp.35-41
• /
• 1988

The optimum test conditions of measuring the crack height were determined for the two-probe ultrasonic diffraction method. The applicability and the accuracy of the two-probe ultrasonic diffraction method on the inclined artificial cracks and the fatigue cracks were evaluated. It us possible to measure the height of the normal and inclined artificial cracks with the maximum error of ${\pm}\;0.5mm$ with the two-probe ultrasonic diffraction method. It was found, however, that the accuracy of this method in meaasuring the height of the fatigue crack depends on the degree of closure of the crack tip. It was desirable to choose a refraction angle as small as possible, but the angle should not be so small that the distortion of the lateral waveform became appreciable.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1995년도 가을 학술발표회 논문집
• /
• pp.41.1-44
• /
• 1995

The JV method is an epochal civil engineering style that boasts of significant pile driving power through low-vibration works by ideally combining the high pressure water injected from the water jet cutter and the vibrations combining from the vibratory pile driver extractors. As a result, you are ensured stable and safe pile driving and extraction in bedrocks that were previously impossible with conventional machines and methods. The other advantage is its high performance and a low-pollution characteristis that is ensured by suppressing ground vibrations. This is a very important factor since it often becomes an issue upon civil engineering in the city. With the addition of this method. the range of steel pipe pile, steel sheet pile and other steel pile use has been drastically expanded. Other advantages of this method incldes accurate works, shortening of the construction period and improved work performance. Since the minimun amount of high pressure water is used to drill the ground, it not only loosens the ground, but also cuts the ground at the tip of the pile to improve driving works.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.41-49
• /
• 2004

Liquid breakup under the variation of AC frequency has been studied experimentally in the electrohydrodynamic atomization. The effect of parameters such as charging voltage, flow rate, nozzle tip inner diameter and power frequency have been considered. This work was performed to investigate the experimental analysis for the effect of AC frequency on breakup process, the mapping of occurrence of disintegration region, and the relationship between the applied power and the droplet radius. The experimental results show that the increase of applied voltage in a certain frequency band leads to a reduction in the droplet size within the limits from 50Hz to 400Hz. The transition phenomena from dripping mode to spindle mode were observed under the band of sudden fall of droplet radius changing ratio, and the synchronous region were produced within the range of applied voltage from 5kV to 6kV.

• Journal of Welding and Joining
• /
• 제18권5호
• /
• pp.41-48
• /
• 2000

Dynamic behaviors of the GMAW system are simulated using the short-circuit transfer model and the characteristic equations fir the power supply, wire system and arc. The conventional wire equation, which relates the rate change of the wire extension to the wire feed rate and melting rate, is modified to include effects of the molten drop attached at the wire tip. The modified wire equation describes behaviors of the GMAW system more precisely and provides information about the initial bridge volume for short-circuit transfer. The proposed short-circuit model predicts the variation of parameters such as the current, voltage, short-circuit frequency and time considering the effects of the surface tension and electromagnetic force due to current. The calculated results are in broad agreements with the experimental results under the argon shielding condition.

• Wind and Structures
• /
• 제17권1호
• /
• pp.21-41
• /
• 2013

Wind-induced vibrations of mast arms of cantilever traffic signal structures can lead to fatigue failure. Two such structures were instrumented each with a sonic anemometer and a camera that records the motions of the tip of the arm. It was observed throughout this experiment that large amplitude vertical vibrations of mast arms with signals with backplates occur for the most part at low wind speed ranges, between 2 to 7 m/s, and as the wind speed increases the amplitude of the vertical vibrations decreases. The results of these experiments contradict the generally accepted belief that vortex shedding does not cause significant vibrations of mast arms that could lead to fatigue failure, which have been attributed to galloping in the past. Two damping devices were tested with mixed results.

• 한국군사과학기술학회지
• /
• 제8권3호
• /
• pp.33-41
• /
• 2005

This paper describes the conceptual design of medium size helicopter rotor system. Based on assumed design requirements, trade-off study for rotor configuration has been conducted in terms of rotor tip speed, disk loading, blade area, solidity, etc for estimated primary mission gross weight. For the main rotor, four-blade and five-blade rotors are studied with the conventional tail rotor. The performance analysis for baseline configuration is conducted using a helicopter performance analysis program. The analysis shows design results satisfy the design requirements.

• Journal of Welding and Joining
• /
• 제24권3호
• /
• pp.34-41
• /
• 2006

The CD (Capacitor Discharge) stud welding utilizes the arc heat and pressure to attach the stud to the workpiece, which consists of the arc. ignition, arcing and pressure welding stages. In order to predict the dynamic behavior of the CD stud welding process, mechanical and electrical models are employed in this work. While the mechanical model estimates the duration of each stage, the electrical model predicts the voltage and current waveforms using the RLC circuit. Effects of process parameters such as the electric components and spring force are analyzed through simulation. It is found that the contact resistance and gap between the stud and base metal influence the tip fusing and arcing duration. The calculated results showed reasonably good agreements with the experiment results.

• 한국작물학회지
• /
• 제41권1호
• /
• pp.77-85
• /
• 1996

쌀보리의 이삭에 관한 기초자료를 얻고자 우리나라에서 육성한 쌀보리의 품종을 공시하여 소수위치에 따른 망의 길이와 무게, 입중 등을 조사한 바 그 결과를 요약하면 다음과 같다. 1. 이삭의 정단부로부터 3∼5번째 소수가 망장 및 망중의 평균치와, 2∼4번째 소수가 입중의 평균치와 각각 일치하였다. 2. 이삭의 기부로부터 3∼4번째 소수의 망이 가장 길고 무거웠으며 5∼6번째 소수의 입중이 가장 무거웠다. 3. 측열 소수는 중앙열 소수에 비하여 망장은 13∼26%, 망중은 26∼41%, 입중은 18∼25% 적은 값을 보였다. nami형 품종은 uzu형 품종에 비하여 중앙열과 측열간 망장, 망중 차이가 적었다. 4. 망중/망장 비로 볼 때 uzu형 품종은 nami형 품종보다, 그리고 중앙열은 측열보다 망이 더 굵었다. 5. 이삭을 3등분하였을 때 망장, 망중은 하부와 중앙부 차이가 없었으나 상부보다는 길고 무거웠다. 입중은 상부가 항상 가벼웠고 중앙부는 하부보다 무겁거나 같았다. 6. 망중이 무거운 소술일수록 입중이 무거웠다.

• 기계저널
• /
• 제16권4호
• /
• pp.41-48
• /
• 1976

재료의 피로문제에 대해서는 꽤 오래 전부터 많은 연구가 이루어져왔고, 피로의 현상파악에서부 터 피로이론의 구명, 나아가서는 실제문제로서의 피로설계, 피로수명예측 등에 기여한 업적은 아 주 크다 하겠다. 그러나 종래의 피로문제연구의 방향이, S-N 곡선에서 얻어지는 피로한계강도 (더 정확한 표현으론 피로파괴한계강동)에 바탕을 두고, 정력확적인 설계관례인 안전계수의 도입 을 빌려, 피로강도를 실용화할려는 선에서 이루어져 왔다고 보겠다. 재료의 피로한계강도란, 그 정의로 미루어, 다분히 정적으로는 극한강도 또는 피로강도의 개념에 견주어 질 수 있는 공칭응 력으로써 탄성학적으로 해석될 수도 없고, 다만 탄역성이론의 개념을 바탕으로 근사해석례만이 허용되고 있을 뿐이다. 재료에는 소위 평활재이건 절결재이건 간에 또 검출여부에 관계없이, 내외 부에 대소각종의 결함이나 역학적 불연속부가 잠재해있음은 이미 공지의 사실이며, 이들 결합, 불 연속부등이 외하중하에서 응분의 응력집중원이 되어 재료를 전반적인 파괴로 몰고 갈 수 있다 함 도, 또한 이러한 역학적거동이 피로파괴에 까지 확장해석될 수 있을 것이란 것도 이미 잘 알려져 있는 터이라 하겠다. 재료내외부의 제결합을 응력집중이 극대인 crack로 대체해서 외하중하에서 의 응력장거동을 해석한 선형탄성파괴역학(LEFM)은, 바로 이러한 실제재료의 강도설계에 보다 큰 정확성을 부여한 방법론적 학문이라 하겠고, 나아가서는 재료의 파괴기구를 파헤치는데 진일 보적인 역학적인 수법이라 하겠다. 취성파괴, 연성파괴에 바탕을 둔 파괴역학(LEFM)을 피로파괴 에 적용시키는 데는 상당한 문제점들을 수반할 것임은 충분히 인지되나, 제한된 경계조건하에서 의 적용 예는 종래의 어떤 방법에 의한 것 보다도 피로강도설계, 안전사용 피로수명예측 등에 획기적인 진전을 보여주고 있다. 파괴역학은 crack 재의 강도학이고, 더 구체적으로 음력학대계수 (stress intensity factor) K 또는 이와 연연되는 parameter 인 strain energy release rate(G), crack-tip plactic zone size r$_{p}$,.rho., crack-tip opening displacement .phi., strain intensity 등을 쓰는 재료강도학이기 때문에, 이 수법을 피로파괴에 적용시킴은, 종래의 공칭응력으로 피로 문제를 다루던 방법과는 판이하다 하겠다. 본고에선 파괴역학의 관점에서 피로구열의 안정성장을 논하고, 과거 10여년간의 피로 crack문제에 대한 연구방법, 실험방법 등을 소개하는 방향으로 고 를 진행시켜 나가겠다.

• 대한치과교정학회지
• /
• 제18권2호
• /
• pp.329-342
• /
• 1988

In methods of finding causes for cleft palate, many cases have been studied by investigators using teratogenic agents. Among them, a synthetic agent known as triamcinolone acetonide (TA) was widely used. When this drug was injected into mice during palatogenesis, it induced lowered body weight and a deformed mandible. But many cases have been studied on growth changes, only of the developmental stages of the palate. Therefore, the objective of this study was to evaluate craniofacial growth in experimentally induced cleft palate mice after finishing palatogenesis namely just before birth. Normal, alcohol treated, and TA treated DDY mice were obtained at 18-days of gestation and heads were prepared for serial sectioning in the sagittal plane. The midsagittal sections were photographically enlarged (${\times}40$) and measurements made to asses the amount of growth. The obtained results were as follows. 1. The incidence of cleft palate was 41.2% when TA was injected. 2. The body weight of the cleft palate group was lower than the control group. 3. In the cleft palate group, mandibular length (H-M) was lighter than the control group. 4. In the cleft palate group, degree of staining was not distinct compared to the control group by the double staining method. 5. In the cleft palate group, anteroposterior posture of the tongue tip to facial plane (C-M) was more posterior than the control group. 6. The cause of posterior posture of the tongue tip to facial plane (C-M) in the cleft palate group, was not short and retracted tongue but the mandibular length was increased. 7. The anteroposterior relationship of hyoid cartilage to cranial base was the same in all groups.