• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.25-30
• /
• 2011

In this paper, we analyzed the electrical characteristics with Micro-cracks in Photovoltaic module. Micro cracks are increasing the breakage risk over the whole value chine from the wafer to the finished module, because the wafer or cell is exposed to mechanical stress. And The solar cells have to with stand the stress under out door operation in the finished module. Here the mechanical stress is induced by temperature changes and mechanical loads from wind and snow. So, we experimentally analyze the direct impact of micro-cracks on the module power and the consequences after artificial aging. The first step, we made micro-cracks in PV module by mechanical load test according to IEC 61215. Next, PV modules applied the thermal cycling test, because micro-cracks accelerated aging by thermal cycling test, according to IEC61215. Before every test, we checked output and EL image of PV module. As the result of first step, we detected little power loss(0.9%). But after thermal cycling test increased power loss about 3.2%.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.6
• /
• pp.293-299
• /
• 2004

In this paper, thermal and mechanical properties of electric epoxy with water aging were discussed. We made elastic epoxy specimen adding a ratio of 0〔phr〕20〔phr〕, 35〔phr〕 and 53〔phr〕 with modifier to existing epoxy. We studied mechanical property of elastic resin after absorption in water from 0 to 484 hours. As a result, diffusion factor of elastic epoxy showed 20-21${\times}$10$^{-4}$ $\textrm{mm}^2$/s and general epoxy showed 9.5${\times}$10$^{-4}$ $\textrm{mm}^2$/s. Elastic property increased linearly according to addiction and decreased according to water absorption. Tensile strength was reduced according to addition. It was affected by water absorption of micro-void of elastic epoxy. Hardness inclined to decrease after increasing according to absorbed time. In water-absorption state, it was experimented a change of heat flow by temperature of elastic epoxy and change of thermal expansion coefficient. DSC (Differential Scanning Calorimetry) and TMA (Thermomechanical Analysis) equipments were used to measure Tg. A temperature ringe of DSC was from -0($^{\circ}C$) to 200($^{\circ}C$). One of TMA was from -0($^{\circ}C$) to 350($^{\circ}C$). In addition, we investigated structural analysis of water absorbed specimen using SEM (Scanning Electron Microscope).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.1
• /
• pp.17-22
• /
• 2016

The activation energy of a material is an important factor that significantly affects the lifetime and can be used to develop a degradation model. In this study, a thermal analysis was carried out to evaluate and collect quantitative data on the degradation of insulation materials like EPR and CSP used for nuclear power plant cables. The activation energy was determined from the relationship between log ${\beta}$ and 1/T based on the Flynn.Wall.Ozawa method, by a TGA test. The activation energy was also derived from the relationship between ln(t) and 1/T based on isothermal analysis, by an OIT test. The activation energy of EPR derived from thermal analysis was used to calculate the accelerated aging time corresponding to the number of years of use, employing the Arrhenius equation, and determine the elongation corresponding to the accelerated aging time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1431-1434
• /
• 2014

The thermal barrier coating (TBC) applied to a gas turbine can be damaged by repeated thermal fatigue during operation, so an evaluation of its durability is needed. Thermally grown oxide (TGO) is generated inside the TBC in a high-temperature environment. The growth of TGO is known to be the main cause of damage to the TBC. Therefore, the durability of TBC should be evaluated according to the growth of TGO. In this research, Kim et al.'s work on the growth of TGO with aging was used as a basis for finite element analysis. The relationship between stress and aging was derived from the finite element analysis results. The durability of the TBC with aging was evaluated through a comparison between the results of the finite element analysis and a bond strength test.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.37 no.1
• /
• pp.17-28
• /
• 2024

Objectives : This study was conducted to reveal the scientific mechanism of the anti-skin aging activity of Kyung-Ok-Ko(KOK), which is highly useful as a Korean traditional medicine and functional food. Methods : The skin wrinkle and aging inhibitory activity of KOK was confirmed through in vitro experiments of human dermal fibroblast neonatal cell(HDFn) and in vivo of C. elegans, and hairless mouse(SKH-1). Results : The amount of the C-terminus of the collagen precursor in the HDFn cell culture medium treated with KOK using an enzymes-linked immunoassay kit. The group treated with KOK 200㎍/㎖ was a 28.3% increase of collagen precursor compared to the control group. KOK showed inhibitory activity of MMP-1 compared to the control group at a concentration of 200㎍/㎖. In addition, KOK 200㎍/㎖ showed significant inhibitory activity of thermal stress and an oxidative stress compared to the control group in C. elegans. Furthermore, KOK showed a concentration-dependent(100mg/kg and 500mg/kg) anti-wrinkle formation effect in UV-irradiated hairless mouse(SKH-1). Additionally, when KOK was administered to UV-irradiated hairless mice, an increase in procollagen -1 and -3 genes expression was observed, and mmp-1 and mmp-9 genes, which increase collagen decomposition, decreased with the administration of KOK. Conclusions : The skin aging inhibition mechanism of Kyung-Ok-Ko(KOK) is presumed to be achieved through suppressing thermal stress and oxidative stress, suppressing mmp-1 and mmp-9 genes, and increasing procollagen-1 and procollagen-3.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.204-207
• /
• 2003

The flip chip bonding utilizing self-aligning characteristic of solder becomes mandatory to meet to tolerances for the optical device. In this paper, a parametric study of aging condition and pad size of sample was conducted. A TiW/Cu UBM structure was adopted and sample was aging treated to analyze the effect of intermetallic compound with time variation. After aging treatment, the tendency to decrease in shear strength was measured and the structure of the fine joint area was observed by using SEM, TEM and EDS. In result, the shear strength was decreased of about 20% in the $100{\mu}m$ sample at $170^{\circ}C$ aging compared with the maximum shear strength of same pad size sample. In the case of the $120^{\circ}C$ aging treatment, 17% of decrease in shear strength was measured at the $100{\mu}m$ pad size sample. Also, intremetallic compound of $Cu_6Sn_5$ and $Cu_3Sn$ were observed through the TEM measurement by using an FIB technique that is very useful to prepare TEM thin foil specimens from the solder joint interface.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1372-1381
• /
• 1996

As recieved boiler tuve steel was aged artificially at $650^{\circ}C$ and$690^{\circ}C$ for various time duration to simulate the material deterioration which could be occurred during the operation of fossiol power plants. And the tensile tests, the microhardness tests and the characterization of carbides formed in the aging process were performed to asses the relationship between the mechanical properties and the effect of thermal aging. Furthernore, the amout of Mo-rich carbide were investigated by ondestructive method by noticing the fact that formation of Mo-rich carbide were investigated by ondestructive melthod by noticing the fact that formation of Mo-rich carbides($Mo_6C$) which stabilizes lastly affects the mechanical properties. It was known that the microhardness results of service exposed materials were similar to the ones which are aged at $650^{\circ}C$. The room temperature measurement showed small variation in the yield points and ultimate strength in materials aged at $650^{\circ}C$. Those properties at $540^{\circ}C$ showed the abrupt decrease compared with as received material even if short aging time. And it was found that $650^{\circ}C$ $690^{\circ}C$ aging cause different effects on mechanical properties, although the temperature time parameters(LMP;Larson-Miller parameter) are same. And it was concluded that the aigng at $650^{\circ}C$ is more appropriate to simulate the service exposed condition. Finally, the relationship between high temperature tensile properties and Ip values were established, which offers a potential way of reliability tests onthe power plant components.

• Composites Research
• /
• v.22 no.3
• /
• pp.35-43
• /
• 2009

In this study, for a radiator hose made of carbon black filled EPDM(ethylene-propylene diene monomer) rubber, a measuring method of crosslink density was established to analyze the aging behaviors under thermo-oxidative stresses. At $125^{\circ}C$, the crosslink density of the rubber specimens decreased slightly in the initial stage, but increased with increasing the aging time. Such variation in crosslink density was similar to that of tensile strength. This might be due to the formation of sulphoxide crosslinks as well as to additional crosslinks made by the reaction of unvalcunized sulfurs. A high temperature aging of rubber specimens at $180^{\circ}C$ caused a slight increase in crosslink density while it did a large decrease in tensile strength and elongation. With aging at high temperature, the formation of carbonyl groups in EPDM molecule chain and formation of sulphoxide crosslink, rather than the crosslink density variation itself, had a large influence on such changes in mechanical property.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.28-43
• /
• 2022

To minimize such loss due to aging, research on energetic materials is being actively conducted though, there are difficulties in identifying the comprehensive aging mechanisms as they focused on the respective materials. In this study, thermal and surface analysis were performed on energetic materials composed of metals(W, Ti, and Zr) and KClO₄ oxidizer to solve the blind spots of this aging study. It was newly found that the metals in the hygrothermally aged compounds can cause significant changes in performance. For example, the growth in the thickness of the oxide film on the metals led to an increase in the average value of activation energy(E_α). In addition, the standard deviation of E_α tends to dependent on the type of metal, which is due to the difference in electronegativity.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.670-680
• /
• 1994

The thermophysical properties of Non-Newtonian fluid as the function of the temperature and the concentration are needed in many rheological heat transfer and fluid mechanics problems. The present work investigated the effects of the concentration and the temperature on the thermophysical properties of purely-viscous Non-Newtonian fluids such as the isobaric thermal expansion coefficient, density, zero-shear-rate viscosity, and zero-shear-rate dynamic viscosity within the experimental temperature range from $25^{\circ}C$ to $55^{\circ}C$. The densities of the test fluids were determined as the function of the temperature by utilizing a reference density and the least square equation for the measured isobaric thermal expansion coefficient. As the concentration of purely-viscous Non-Newtonian fluid was increased up to 10,000 wppm, the densities were proportionally increased up to 0.4%. The zero-shear-rate viscosities of test fluids were measured before and after the measurements of the first thermal expansion coefficients and the densities of Non-Newtonian fluid. Even though they were changed up to approximately 22% due to thermal aging and cycling, they had no effects on the thermal expansion coefficients and the densities of Non-Newtonian fluid. The zero-shear-rate dynamic viscosities for purely-viscous Non-Newtonian fluids were compared with the values for distilled water. They showed the similar trend with the zero-shear-rate viscosities due to small differences in the densities for both distilled water and purely-viscous Non-Newtonian fluid.