• Journal of Power System Engineering
• /
• v.17 no.6
• /
• pp.122-129
• /
• 2013

The microstructure and deformation behavior in 22Cr-0.2N micro-duplex stainless steels with various Ni and Mn contents were compared using by OM, TEM, and XRD. The 22Cr-0.2N duplex stainless steel plates were fabricated and hot rolled, followed by annealing treatment at the temperature range of $1,000-1,100^{\circ}C$. All the samples showed the common strain hardening behaviour during the tensile test at a room temperature. The steels tested at the temperatures of $-30^{\circ}C$ or $-50^{\circ}C$ showed a distinct inflection point in the stress-strain curves, which should be resulted from the formation of strain-induced martensite(SIM) of austenite phase. This was confirmed by TEM observations. The onset strain of a inflection point in a stress-strain curve should be depended up the value of $M_d30$. With the decrease of the tensile test temperature, the inflection point appeared earlier, and the strength and fracture strain were higher. The tensile behaviour was discussed from the point of austenite stability of the micro-duplex stainless steels with the different Ni and Mn content.

• Korean Journal of Crystallography
• /
• v.14 no.2
• /
• pp.79-83
• /
• 2003

The microstructure of bulk electrolytic MnO₂ (EMD) was studied using x-ray diffraction and transmission electron microscopy (TEM). The bulk sample showed a typical powder x-ray diffraction pattern of EMD materials. TEM study showed that the structure of EMD is present at two length scales;grains, ∼0.2 ㎛ in diameter, and ∼10 nm crystallites within the grain. The electron beam microdiffraction study revealed that each grain is an assemblage of multiphase with a common crystallographic orientation, and_that ∼50% of the crystallites are Ramsdellite, ∼30% are ε-MnO₂, and ∼15% are Pyrolusite. The ｛1120｝peak located at about 67° in powder XRD pattern as well as a high-resolution electron microscope (HREM) image of (0001) plane support the existence of ε-MnO₂ phase.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.5
• /
• pp.605-614
• /
• 2014

This study investigated microstructural changes of cured urea-formaldehyde (UF) resins mixed with aqueous rubber latex emulsion after intentional acid etching. Transmission electron microscopy (TEM) was used in order to better understand a hydrolytic degradation process of cured UF resins responsible for the formaldehyde emission from wood-based composite panels. A liquid UF resin with a formaldehyde to urea (F/U) molar ratio 1.0 was mixed with a rubber latex emulsion at three different mixing mass ratios (UF resin to latex = 30:70, 50:50, and 70:30). The rate of curing of the liquid modified UF resins decreased with an increase of the rubber latex proportion as determined by differential scanning calorimetry (DSC) measurement. Ultrathin sections of modified and cured UF resin films were exposed to hydrochloric acid etching in order to mimic a certain hydrolytic degradation. TEM observation showed spherical particles and various cavities in the cured UF resins after the acid etching, indicating that the acid etching had hydrolytically degraded some part of the cured UF resin by acid hydrolysis, also showing spherical particles of cured UF resin dispersed in the latex matrix. These results suggested that spherical structures of cured UF resin might play an important role in hindering the hydrolysis degradation of cured UF resin.

• Journal of Technologic Dentistry
• /
• v.25 no.1
• /
• pp.21-28
• /
• 2003

The purpose of this study was to process bio-active glass ceramic composite, reinforced with sapphire fibers, by hot press. Also to study the interface of the matrix and the sapphire fiber, and the mechanical properties. Glass raw materials melted in Pt crucible at 1300$^{\circ}C$ during 3.5 hours. The melt was crushed in ball mill and then crushed material, ground and sieved to $<40{\beta}{\mu}m$. Sapphire fibers cut (30mm) and aligned. Powder and fibers hot pressed. The micrographs show good bonding between the matrix and the fiber and no porosity in the glass matrix. This means ideal fracture phenomena. Glass is fractured before the fiber. This is indication of good fracture strength. EDXS showing aluminum rich phase and crystalline phase. Bright field image of the matrix showing crystalline phase. Also diffraction pattern of TEM showing the crystalline phase and more than one phase. Strength of the samples was determined by 3 point bend testing. Strength of the 10vol% sample was approximately 69MPa, while strength of the control sample is 35MPa. Conclusions through this study as follow: 1. Micrographs show no porosity in the glass matrix and the interface. 2. The interface between the fiber and the glass matrix show no gaps. 3. Fracture of the glass indicates characteristic fiber-matrix separation. 4. Presence of crystalline phase at high processing temperature. 5. Sapphire is compatible with bioactive glass.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.6
• /
• pp.279-287
• /
• 2013

Oxide Dispersion Strengthened (ODS) Fe with $Al_2O_3$ dispersoid was successfully produced by reactive milling with a mixture of Fe, $Fe_3O_4$ (Magnetite), $Fe_2O_3$ (Hematite) and Al reactants at cryogenic temperature. The milled powders were consolidated by Vacuum Hot Press (HP) at 1323 K, and the consolidated materials were characterized by Transmission Electron Microscopy (TEM), Scanning Transmission Electron Microscopy (STEM), and Energy Dispersive Spectroscopy (EDS); the yield strength and the hardness of the consolidated materials were determined by compressive test and Vickers hardness test at room temperature. The grain size of the materials was estimated by X-ray Diffraction technique using the scherrer's formula. The TEM observations showed that the microstructure was comprised with a mixture of nanocrystalline Fe matrix and $Al_2O_3$ nano-dispersoids with a bimodal size distribution; the 0.2% off-set yield strength of the materials was as high as $758{\pm}29$ MPa and the Vickers hardness was $358{\pm}2$. The effect of the cryogenic milling and addition of extra Fe powder was discussed on the suppression of MSR (Mechanically induced Self-sustaining Reaction) for the desired microstructural evolution of ODS alloys.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.336-342
• /
• 2003

(Sm/Y)$_{1.8}$B $a_{2.4}$C $u_{3.4}$$O_{7-x}$ [(Sm/Y)1.8] high $T_{c}$ superconductors were directionally grown by Rod-type Seed Melt Growth(RSMG) process in air atmosphere. The sintered polycrystalline N $d_{1.8}$B $a_{2.4}$C $u_{3.4}$$O_{7-x}$(Nd1.8) of rod-type seed crystal grown by extrusion mold process were used for achieving the ab-plane alignment haying large grains perpendicular to the center of (Sm/Y)1.8 samples. The observations using TEM micrographs of the melt-textured (Sm/Y)1.8 samples revealed that the nonsuperconducting (Sm/Y)211 inclusions are uniformly distributed in the superconducting (Sm/Y)123 matrix. The microstructure and superconducting properties were investigated by XRD, TEM and SQUID magnetometer. The RSMG (Sm/Y)1.8 samples showed an onset $T_{c}$ $\geq$ 90 K and sharp superconducting transition.nsition.ion.nsition.

• Applied Microscopy
• /
• v.45 no.3
• /
• pp.170-176
• /
• 2015

In this work, various electron microscopy and analysis techniques were used to investigate the microstructural evolution of a 9% Cr tempered martensite ferritic (TMF) steel T91 upon ultrasonic nanocrystalline surface modification (UNSM) treatment. The micro-dimpled surface was analyzed by scanning electron microscopy. The characteristics of plastic deformation and gradient microstructure of the UNSM treated specimens were clearly revealed by crystal orientation mapping of electron backscatter diffraction (EBSD), with flexible use of the inverse pole figure, image quality, and grain boundary misorientation images. Transmission electron microscope (TEM) observation of the specimens at different depths showed the formation of dislocations, dense dislocation walls, subgrains, and grains in the lower, middle, upper, and top layers of the treated specimens. Refinement of the $M_{23}C_6$ precipitates was also observed, the size and the number density of which were found to decrease as depth from the top surface decreased. The complex microstructure and microstructural evolution of the TMF steel samples upon the UNSM treatment were well-characterized by combined use of EBSD and TEM techniques.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.243-243
• /
• 2007

We have studied the electrical properties and microstructure of $(Y_{0.5}Nd_{0.25}Sm_{0.25})Ba_2Cu_3O_y[(YNS)-123]$ Oxides by rod-type seeded melt growth process(RSMG) in air atmosphere. Rod-type $NdBa_2Cu_3O_y${Nd-123) seed crystals made a extrusion process method, were used for achieving the ab-plane alignment having large grains perpendicular to the center of (YNS)-123 samples. The observations using SEM and TEM micrographs of the melt-textured (YNS)-123 samples revealed that the nonsuperconducting $(Y_{0.5}Nd_{0.25}Sm_{0.25})Ba_2Cu_3O_y[(YNS)-211]$ inclusions are uniformly distributed in the superconducting matrix. The microstructure and electrical properties were investigated by XRD, SEM, TEM and DC SQUID magnetometer. The sample showed a sharp superconducting transition at 90 K. The magnetization values of the (YNS)-123 sample exhibited the enhanced electrical properties, compared with $YBa_2Cu_3O_y$(Y-123) sample.

• Applied Microscopy
• /
• v.45 no.4
• /
• pp.195-198
• /
• 2015

Gas-assisted etching (GAE) with focused ion beam (FIB) was applied to prepare plan-view specimens of Cu thin-layer on a silicon substrate for transmission electron microscopy (TEM). GAE using $XeF_2$ gas selectively etched the silicon substrate without volume loss of the Cu thin-layer. The plan-view specimen of the Cu thin film prepared by FIB milling with GAE was observed by scanning electron microscopy and $C_S$-corrected high-resolution TEM to estimate the size and microstructure of the TEM specimen. The GAE with FIB technique overcame various artifacts of conventional FIB milling technique such as bending, shrinking and non-uniform thickness of the TEM specimens. The Cu thin film was uniform in thickness and relatively larger in size despite of the thickness of <200 nm.

• Elastomers and Composites
• /
• v.58 no.4
• /
• pp.208-215
• /
• 2023

In this study, the properties of polyurethane-polydimethylsiloxane (PU-PDMS) hybrid foams containing different types and contents of physical blowing agents (PBAs) were investigated. Two types of blowing agents, namely physical blowing agents and thermally expandable microspheres (TEM), were applied. The apparent density was measured using precisely cut foam samples, and the pore size was measured using image software. In addition, the microstructure of the foam was confirmed via scanning electron microscopy and transmission electron microscopy. The thermal conductivities related to the microstructures of the different foams were compared. When 0.5 phr of the hydrocarbon-based PBA was added, the apparent density and pore size of the foam were minimal; however, the pore size was larger than that of neat foam. In contrast, the addition of 3 phr of TEM effectively reduced both the apparent density and pore size of the PBAs. The increase in resin viscosity owing to TEM could enhance bubble production stability, leading to the formation of more uniform and smaller pores. These results indicate that TEM is a highly efficient PBA that can be employed to decrease the weight and pore size of PU-PDMS hybrid foams.