• Journal of the military operations research society of Korea
• /
• v.2 no.1
• /
• pp.185-194
• /
• 1976

A terminal response time analysis for a general class of terminals-to-computer subsystem is presented in this paper. On the point of the front view, it should be considered for R.O.K. Military Defense to set up the communication network in order to facilitate for the currency of the information and the data communication system. The model used to study is based on the advanced data communications system in which terminals are connected to Terminal Control Units(TCU) that are in turn connected to local Front-End Processor(FEP). The line control procedures used to interface a TCU and an FEP may be half-duplex Binary Synchronous Communication(BSC), half-duplex Synchronous Data Link Control(SDLC), or full-duplex SLDC. This paper will contribute to facilitate the initial phase of system design and configuration for the Military Defense Communication Network System in future.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.3
• /
• pp.118-126
• /
• 2010

The automated mechanical transmission(AMT) is composed of electronic control management(ECM) and automatic shift gear(ASG). The AMT has advantages which are high efficiency of manual transmissions(MT) and offer operation convenience similar to automatic transmissions(AT). However, it has defects that are the torque gap during gear shift transients and shift time is long. To reduce such defects, it is necessary practically to evaluate error and characteristics as developing simulation model before the control algorithm is applied. In this paper, models are composed of vehicle model and AMT shift control model. Particularly AMT shift control model consists of main clutch management model (MCM) and shift control management model(SCM). The developed models were verified by comparing the simulated and experimental results under the same operational conditions. It can also be used to evaluate shift algorithm.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.5
• /
• pp.795-801
• /
• 1994

The BiPbSrCaCuO superconductor was fabricated by diffusion of The dual layer composed of SrS12TCaS11TCuS12TOS1xT in upper layer and BiS12TPbSI0.3TCuS12TOS1yT in lower layer, and varified growh-mechanism of BiPbSrCaCuO superconducting phase. And, we produced optimum conditions of spread volume and each stage of sintering time were upper layer:Lower layer=1:0.2, 1:0.4, 1:0.6 and 24hr., 120hr., 210hr. From the result, the optimum conditions are spread volume(Upper layer:Lower layer=1:0.6), sintering time(210hrs.) at 820$^{\circ}C$.The BiPbSrCaCuO superconductor, fabricated optimum condition, showed zero resistance at critical temperature of 70k.

• Journal of the KSME
• /
• v.53 no.11
• /
• pp.32-38
• /
• 2013

이 글에서는 자동차 구동장치 핵심요소 중의 하나인 자동변속장치의 구조와 기능에 대해 살펴보고 변속제어 장치인 TCU에 적용되는 IT기술에 대하여 소개하고자 한다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.301-306
• /
• 2008

Drivers are becoming more fatigued and uncomfortable with increase in traffic density, and this condition can lead to slower reaction time. Consequently, they may face the danger of traffic accidents due to their inability to cope with frequent gear shifting. To reduce this risk, some drivers prefer automatic transmission (AT) over manual transmission (MT). The AT offers more superior drivability and less shifting shock than the MT; therefore, the AT market share has been increasing. The AT is controlled by an electronic control unit (ECU), which provides better shifting performance. The transmission control unit (TCU) is a higher-value-added product, so the companies that have advanced technologies end to evade technology transfer. With more cars gradually using the ECU, the TCU is expected to be faster and more efficient for organic communication and arithmetic processing between the control systems than the l6-bit controller. In this paper, the model of an automatic transmission vehicle using MATLAB/Simulink is developed for the Hardware in-the-Loop (HIL) simulation with a 32-bit embedded system, and also the AT control logic for shifting is developed by using MATLAB/Simulink. The developed AT control logic, transformed automatically by real time workshop toolbox, is loaded to a 32-bit embedded system platform based on Freescale's MPC565. With both vehicle model and 32-bit embedded system platform, we make the HIL simulation system and HIL simulation of AT based on real time operating system (RTOS) is performed. According to the simulation results, the developed HIL simulator will be used for the performance test of embedded system for AT with low cost and effort.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.203-208
• /
• 2005

Electronic components for space launch vehicles are exposed to a severe vibrational environment at launch and flight. The structural reliability of each component can be verified using mathematical approaches. In order to verify the structural reliability, an important parameter is the natural frequency of PCB(Printed Circuit Board) assembly mounted electronic components on and housing mounted PCB assembly in. In this paper, in order to find natural frequencies of PCB assemblies and the housing of hydrazine TCU(Thruster Control Unit), FEM(Finite Element Method) is adapted. The analytical result of FEM is verified by experimental method.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.5
• /
• pp.525-532
• /
• 1992

Fluorine-doped YBaS12TCuS13TOS17-xTFS1yT superconducting materials with y varing two orders of magnitude form 0.02 to 2.0 have been prepared by a sol-gel process by using metal nitrate salts, sodium hydroxide and sodium fluoride. Fluorine contents have been measured using an ion-selective electrode. All fluorine doped as reactant were found to be present in the resulted samples. From the observation of XRD it has been concluded that the samples with y 0.2 formed simply the single phase of perovskite structure, whereas those with y 0.5 yielded together some compounds such as BaFS12T, YFS13T and CuO in the resulted samples. The observation of solid state S019TF NMR has been carried out in order to check whether fluorine was actually incorporated into the lattice sites, and the experimental results revealed that the mole ratio of fluorine incorporated into the lattice sites of YBaS12TCuS13TOS17-xT was approximately 0.2 per mole of the compound. Also electrical resistivity measurement indicated that onset transition temperature has the tendency to increase slightly with increasing y in the dilute region as y 0.2.

• Journal of Drive and Control
• /
• v.13 no.1
• /
• pp.1-9
• /
• 2016

Nowadays automatic transmission equipped vehicles prevail in construction and agricultural equipment due to their convenience in driving and operation. Though domestic vehicle manufacturers install imported electronic controlled transmissions at present, overseas products will be replaced by domestic ones in the near future owing to development efforts over the past 10 years. For passenger cars, there are many kinds of shift control algorithms that enhance the shift quality such as feedback and learning control. However, since shift control technologies for heavy duty vehicles are not highly developed, it is possible to improve the shift quality with an organized control method. A feedback control algorithm for neutral-into-gear shift, which is enabled during the inertia phase for the master clutch slip speed to track the slip speed reference, is proposed based on the power transmission structure of TH100. The performance of the feedback shift control is verified by a vehicle test which is implemented with firmware embedded TCU. As the master clutch engages along the predetermined speed trajectory, it can be concluded that the shift quality can be managed by a shift time control parameter. By extending the proposed feedback algorithm for neutral-into-gear shift to gear change and shuttle shift, it is expected that the quality of the shift can be improved.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.36-46
• /
• 1993

In CVT vehicle, the engine speed is completely decoupled from the vehicle speed within the range from maximum transmission ratio to minimum transmission ratio. This allows the engine to operate in optimal state(e.g. best fuel economy or maximum power mode.) In this study, the CVT control algorithm for optimal operation of engine is suggested. In order to implement the real time digital control of electro-hydraulic CVT system, a software called CVTCON has been developed. CVTCON also includes the CVT operation module, (2) system test module, (3) system control module and (4) data management module. By using the CVTCON and the electro-hydraulic CVT system, two modes of experiments were carried out: constant throttle opening mode and acceleration mode. From the experimental result, it was found that the algorithm suggested in this study showed optimal operation of the CVT system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.966-970
• /
• 2005

On the basis of the development of KSLV-1, KoDSat was designed and manufactured to demonstrate the performance of KSLV-1. KoDSat is exposed to a severe vibrational environment at launch. The structural reliability of KoDSat has to be verified using vibrational test. The structural compatibility and verification of components between analysis and test can be proved using environmental vibration test. In this paper, we review the structural characteristic of thruster control unit for a space launch vehicle and design TCU housing using mathematical model. In order to verify the structural compatibility and reliability, half-sine shock, random and sing sweep vibration test was performed. Especially, sing sweep vibration test result is compared with analysis result and mathematical model is verified.