• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.99-106
• /
• 1993

A relationship $(T_c = -17.869C^2+1840.2C-46623)$ between Curie Temperature$(T_c)$ and (C), $Li_2O$ mole percent(%) was established from the measurement results of Curie temperature $(T_c)$) analysed by DTA(Differential Thermal Analysis) in the range from 48.50 to 49.00 $Li_2O$ mole %. Congruent melt composition of $LiTaO_3$ single crystal was to be 48.65 $Li_2O$ mole % and its Curie temperature was also determined to be $610{\pm}1^{\circ}C$ from the results of Curie temperature difference, ${\Delta}T (T_{c(Top)}-T{_c(Tail)})$ of Czochralski grown $LiTaO_3$ crystals and the distribution coefficient(k). The k was calculated from $LiO_2$ mole ratio of initial melt to final melt and initial crystal to final crystal in the range from 48.60 to 48.70 $Li_2O$ mole %.

• Physical Therapy Korea
• /
• v.17 no.2
• /
• pp.10-16
• /
• 2010

This study was undertaken to develop the scapulometer, a measuring tool for scapular winging, and to determine the reliability of scapulometer. Thirty subjects with scapular winging greater than 2 cm participated in this study. Two examiners measured scapular winging using the scapulometer. Standardized measurement position of each subject was as follows: neutral position of shoulder and wrist, $90^{\circ}$ flexion of elbow, and cuff weight of 5% and 10% of body weight (BW) to neutral wrist. The interrater and intrarater reliability were calculated with an intraclass correlation coefficient (ICC) with 95% confidence interval (CI) and standard error of measurement (SEM) at 5% BW and 10% BW. The level of scapular winging was tested between 5% BW and 10% BW with a paired t-test. The interrater reliability was shown to be high at 5% BW (ICC(2,k)=.955, 95% CI=.900~.979, SEM=.07) and at 10% BW (ICC(2,k)=.968, 95% CI=.930~.985, SEM=.06). The intrarater reliability was shown to be high at 5% BW (ICC(2,k)=.921, 95% CI=.842~.961, SEM=.09) and at 10% BW (ICC(2,k)=.906, 95% CI=.813~.954, SEM=.10). The level of scapular winging was significantly different between 5% BW and 10% BW. Conclusively, it is demonstrated that the scapulometer is an objective and qualitative measurement tool for scapular winging.

• International Journal of Contents
• /
• v.15 no.2
• /
• pp.75-78
• /
• 2019

The Integration technique of combining the measurement method with the fine precision of the sensor collecting the satellite-based information to determine the displacement space is available to a variety of diagnostic information. The measurement method by a GNSS with the sensors is needed since there will always be occasional occurrence of natural disasters caused by various environmental factors and the surroundings. Such attempts carried out nationally by distributed torsional displacement of the terrain and facilities. The combination of the various positioning analysis of mm-class for the facility of main area observed is required constantly in real time information of the USN/IoT Smart sensors and should be able to utilize such information as a precisely fine positioning information for the precisely fine displacement of the semi-permanent main facilities. In this study, for the installation of the receiving system, the USN/IoT base line positioning are easily accessible for the target bridges. Transmitting hourly from the received data is also executed in real time using the wireless Wi-Fi/Bluetooth bridges and related facilities to automatically process a fine position displacement. The results obtained from this method can be analyzed by real-time monitoring for a large structure or facilities for disaster prevention.

• Journal of Environmental Science International
• /
• v.26 no.4
• /
• pp.467-481
• /
• 2017

This study sought to determine the changes in weather conditions in urban streets, along with conditions of traffic and roads in urban areas. The variations in weather conditions depending on traffic differed according to distance. First, the temperature difference measured by traffic results is as follows: T1 point $1.03^{\circ}C$, T2 point $1.04^{\circ}C$, T3 point $0.9^{\circ}C$, T4 point $1.01^{\circ}C$, and T5 point $0.31^{\circ}C$. The average difference between the measured temperatures by the point of measurement was $0.86^{\circ}C$. The changes in wind velocity according to traffic volume results of the measurements is T1 point 1.32 m/s, T2 point 0.80 m/s, T3 point 0.29 m/s, T4 point 0.04 m/s, and T5 point 0.09 m/s. The difference between the average wind speeds was 0.51 m/s and traffic jams caused substantial differences in distance. The relative humidity tended to be inversely proportional to temperature. The measurements results ares T1 point 2.29%, T2 point 2.67%, T3 point 2.47%, T4 point 2.16%, and T5 point 0.91% The difference between the average relative humidity was 7.3%. In case of independent sampling T test according to traffic volume, changes in wind velocity and temperature were directly proportional to the level of statistical significance(p<0.01). On the other hand, relative humidity tended to be inversely proportional; however, there was no statistical significance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.167-168
• /
• 2007

$CdIn_2S_4$ (110) films were grown on semi-insulating GaAs (100) by a hot wall epitaxy method. Using photocurrent (PC) measurement, the PC spectra in the temperature range of 30 and 10 K appeared as three peaks in the short wavelength region. It was found that three peaks, A-, B-, and C-excitons, correspond to the intrinsic transition from the valence band states of ${\Gamma}_4(z),\;{\Gamma}_5(x),\;and\;{\Gamma}_5(y)$ to the exciton below the conduction band state of ${\Gamma}_1(s)$, respectively. The 0.122 eV crystal field splitting and the 0.017 eV spin orbit splitting were obtained. Thus, the temperature dependence of the optical band gap obtained from the PC measurement was well described by $E_g$(T)=2.7116eV - $(7.65{\times}10^{-4}\;eV/K)T^2$/(425+T). But, the behavior of the PC was different from that generally observed in other semiconductors. The PC intensities decreased with decreasing temperature. This phenomenon had ever been reported at a PC experiment on the bulk crystals grown by the Bridgman method. From the relation of log $J_{ph}$ vs 1/T, where $J_{ph}$ is the PC density, two dominant levels were observed, one at high temperatures and the other at low temperatures. Consequently, the trapping centers due to native defects in the $CdIn_2S_4$ film were suggested to be the causes of the decrease in the PC signal with decreasing temperature.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.18 no.6
• /
• pp.737-745
• /
• 2008

Recent developments of process and measurement technology bring much interest to the online monitoring of process operations such as milling, grinding, broaching, etc. The objective of online monitoring systems is to detect process changes as early as possible. This is helpful in protecting facilities against unexpected failures and then preventing unnecessary loss. This paper investigates, when the process monitoring data are obtained as a profile, the monitoring performances of a statistical $T^2$-statistic and a feedforward neural network by using a wavelet transform. Numerical experiments using cutting force data presented by Axinte show that the proposed wavelet based $T^2$-test has an acceptable power in detecting profile changes. However, its operating characteristic is very sensitive to autocorrelation. On the contrary, compared with $T^2$-test, the neural network has more stable performance in the presence of autocorrelation. This indicates that an adaptive feature to analyze noises should be incorporated into the wavelet based $T^2$-test.

• Journal of the Korean Magnetics Society
• /
• v.20 no.5
• /
• pp.178-181
• /
• 2010

Search coil magnetometer has been used for detection of ac magnetic field with high sensitivity. To reduce demagnetizing factor of core and increase S/N ratio of search coil magnetometer, the core was divided by two parts and coil was wound on each cores. Two coils were connected serially and put into amplifier as differential mode. Constructed 120 mm length search coil magnetometer shows linearity of 0.03%, sensitivity of 9.3 mV/nT, and resolution of 20 pT at 1 Hz.

• International journal of advanced smart convergence
• /
• v.12 no.1
• /
• pp.9-17
• /
• 2023

Recently, IoT technology has been widely used in many industries. Also research on integrating IoT technology with IoT sensors is actively underway. One of the important challenges in IoT is to support low-latency communication. With the development of communication networks and protocols, a variety of protocols are being used, and their performance is improving. In this paper, we compare the performance and analyze the characteristics of some of the major communication protocols in IoT application, namely MQTT, HTTP, and HTTPS. IoT sensors acquired data by connecting an Arduino equipped with ESP8266 and a temperature and humidity sensor (DHT11). The server measured the performance by building servers for each protocol using AWS EC2. We analyzed the packets transmitted between the Arduino and the server during the data transmission. We measured the amount of data and transfer time. The measurement results showed that MQTT had the lowest data transmission time and data amount among the three protocols.

• Bulletin of the Korean Chemical Society
• /
• v.16 no.1
• /
• pp.53-58
• /
• 1995

Heats of solution of aniline (AN), benzylamine (BA), ethyl-(EBS) and 2-phenylethyl benzenesulfonates (PEB) are calorimetrically measured in acetonitrile-methanol mixtures at 25.0 $^{\circ}C$. The activation parameters, ${\Delta}H^{\neq}$, ${\Delta}S^{\neq}$ and ${\Delta}G^{\neq}$, are determined for the reactions of EBS and PEB with AN and BA using the kinetic data at three temperatures. Calorimetric transfer enthalpies of initial state, ${\delta}H_t^{0{\rightarrow}x})$(IS), and kinetically derived activation enthalpies, ${\delta}\;{\Delta}H^{\neq}$, in the MeCN-MeOH mixtures are combined to determine the transfer enthalpies of transition state, ${\delta}H_t^{0{\rightarrow}x})$(TS); ${\delta}H_t^{0{\rightarrow}x})$(IS) = ${\delta}{\Delta}H^{\neq}\;+\;{\delta}H_t^{0{\rightarrow}x}$(IS) The preferential solvation of anionic charge in the TS predicts a loose TS with a greater degree of bond cleavage for the reactions of PEB than for EBS, and also for the reactions with BA compared to the reactions with AN.

• Journal of the Korean institute of surface engineering
• /
• v.20 no.4
• /
• pp.144-153
• /
• 1987

In the case of dipping the Ni-Resist cast iron into molten aluminum with iron content, the thickness of intermetallic compound was remarkably increased with increasing iron content. The thickness was shown by following equation in the range of 1-3% iron content; $x=22.5t^{1/2}+4.47{\cdot}t{\cdot}(Fe%)$. where, x is thickness(${\mu}m$), t the time (minute), Fe% the iron w/o. When the Ni-Resist cast iron was dipped into the molten aluminum containing zinc content, the intermetallic compound thickness was also increased with increasing zinc contents. And thickness was represented by the following equation in the range of 2-10% zinc content; $x=3.46t^{1/2}+0.27{\cdot}t{\cdot}(Zn%)$. However, in the case of dipping the Ni-resist cast iron into molten aluminum with silicon content, the thickness of intermetallic compound was decreased with increasing silicon content, as shown in the following equation; $x=7.17t^{1/2}-0.15{\cdot}t{\cdot}(Si%)$. The intermetallic compound formed onto Ni-Resist cast iron was identified to be $FeAl_3\;and\;Fe_3Al$. As the result of hardness measurement, the peak hardness appeared in the intermetallic compound at near interface of the cast iron and the compound.