• Korean Journal of Agricultural Science
• /
• v.23 no.1
• /
• pp.25-38
• /
• 1996

To investigate the stability problem of irrigation-drainage channel excavation slope on soft ground, analyzed the behavior of the soft ground with excavation slope by the limit equilibrium method and the finite element method, and compared with field tests. The results of this study were summarized as follows; 1. When rapid drawdown the water level, the crack was occurred by the effect of the excess pore water pressure, and the pore water pressure was decreased slowly. 2. As the width of excavation was larger, the crack width was larger. And, excavated depth was deeper, the progressive failure was appeared. 3. When the soft ground excavation was small-scale, the minimum safety factor was more effected by cohesion(1.0, 1.5, 2.0, 2.5, 3.0) than excavated slope inclination(1:l, 1:1.5, 1:2). 4. As excavation was progressed, the settlement occurred on the top-slope due to plastic domain, and heaving was occurred at the bottom of excavation. 5. The maximum shear stress was appeared greatly as the base part of slope went down. Because of the increase of the maximum shear stress, tension area occurred and local failure possibility was increased. 6. As the excavation depth was increased, the maximum shear strain was appeared greatly at the base of slope and distribution pattern was concentrated beneath the middle of slope.

• Journal of Korean Neurosurgical Society
• /
• v.64 no.5
• /
• pp.784-790
• /
• 2021

Objective : The purpose of this study was to investigate the correlations among various radiological parameters used to determine cervical alignment from cervical spine radiographs (X-CS) and cervical spine computed tomography (CT-CS), both within and between modalities. Methods : This study included 168 patients (≤60 years old) without a definite whole spine deformity who underwent CT-CS and X-CS. We measured occipital slope (O-s), C1 slope, C2 slope, C7 slope, sella turcica - C7 sagittal vertical axis (StC7-SVA), spino-cranial angle, T1 slope, and C27-SVA. We calculated the O-C2 angle, O-C7 angle, and C2-7 angle from the measured parameters and conducted correlation analyses among multiple parameters. Results : The intrinsic correlation features among multiple cervical parameters were very similar for both X-CS and CT-CS. The two SVA parameters (C27-SVA and StC7-SVA) were mainly influenced by the upper cervical slope parameters (r=|0.13-0.74|) rather than the lower slope cervical parameters (r=|0.08-0.13|). The correlation between X-CS and CT-CS for each radiological parameter was statistically significant (r=0.26-0.44) except for O-s (r=0.10) and StC7-SVA (r=0.11). Conclusion : The correlation patterns within X-CS and CT-CS were very similar in this study. The correlation between X-ray and CT was statistically significant for most radiological parameters, and the correlation score increased when the horizontal gaze was consistently maintained. The lower cervical parameters were not statistically associated with translation-related parameters (C2-7 SVA and StC7-SVA). Therefore, the upper cervical segment may be a better predictor for determining head and neck translation.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2001.11a
• /
• pp.200-200
• /
• 2001

백판지 면성은 표면 백색도의 변이, 불투명도의 변이, 광택도, 거치름도, 표면 지합, 표면 요철 등 다양한 인자들로 표현되고 있다. 인쇄소에서는 인쇄를 하기 때문에 화선 부에서의 백색도나 불투명도 등은 크게 불만 요소로 작용하지는 않으나 표면 요철의 경우에는 인쇄 후 화선부에서도 나타나기 때문에 고객 불만의 한 요소로 인식되어 진 다. 따라서 본 연구에서는 백판지 면성의 여러 인자 중 표면 요철의 평가에 대해 다루 고자 하였다. 백판지 표면 요철을 시각적으로 나타내기 위한 방법으로 3-Dimensinal topography를 얻을 수 있는 Zygo와 Stylus를 이용, FFT 변환을 통하여 2-dimensional topography를 얻는 방법이 연구되었다. 그러나 기자재 비용, 측정 시간 등의 문제 등으로 표면 요철 을 평가하기 어려운 점이 있다. 본 연구에서는 백판지를 T APIO를 이용하여 O.2mm간격으로 두께를 측정하였고 A verage slope와 Profile length라는 개념을 도입하여 수치 적으로 표면 요철을 정 량화 하였다. Average slope는 1mm 간격으로 이동하였을 때 높이의 편차를 평균하는 값이다. 또 한 Video eam을 이용하여 표면 요철의 형태를 촬영하여 시각적으로 판단할 수 있도록 하였다. 위의 측정 방법으로 국내, 외 12개의 Sample에 대해 Profile length와 Average s slope를 계산하였다. 고객의 주관적 평가를 의사결정 방법 중 하나인 AHP법을 이용하여 주관적인 정성 평가를 수치적으로 정량화할 수 있었으며 실제 측정 결과와 비교, 상관분석을 실시 하 였다. 고객의 평가 결과와 Profile length, average slope의 상관성을 분석한 결과 A Average slope에서 유의성 있는 상관성을 얻을 수 있었고 표면 사진을 비교하였을 때 C Coating 방식 등을 유추할 수 있었다. 이러한 평가 방법을 현장에 적용하였으며 그 결과, 공정 개선 전, 후의 표변을 측정, 개선 유무를 쉽게 판단할 수 있었다.

• Journal of the Korean Institute of Rural Architecture
• /
• v.2 no.1
• /
• pp.101-112
• /
• 2000

Green environment is most important factor to human being taking a side view of psychological aspect. But, as the civilization progresses rapidly, the green environment decreases. At present, various environmentally friendly methods are developed to prevent the ill effect of the concretes. n this study, Ecostone retaining wall method, which is a kind of environmentally friendly block, are used for verifying the application to the slope stability and protection of rural hosing. In case of rural hosing and structure, the height of the slope is not high and additional loading doesn't act on the slope except the gravity loading of housing and structure. From the result of the stability analysis of Ecostone, 3m to 7m Ecostone retaining wall can have an equivalence capacity comparing with the concrete retaining wall. Therefore, Ecostone method can apply to retaining wall with the structural safety and environmentally friendly aspect using the plants and vegetation.

• Bulletin of the Korean Chemical Society
• /
• v.25 no.9
• /
• pp.1361-1365
• /
• 2004

Solvatokinetic and solvatochromic behavior of bis(indolinobenzospiropyranyl) sulfide derivatives 1a-1c have been studied in various solvents. The marked negative solvatochromism is exhibited for 1a and 1b in the whole region of solvent polarity examined. Whereas, it is found only in the polar solvent region ($E_T$ > 37) for 1c. The sensitivity order to the solvent media (slope values) is 1a > 1b > 1c. The branched linear plot with a zero slope was shown for the most sterically-hindered compound 1c in the less polar-solvent region (($E_T$ < 37). The biphasic plot is indicative of dual mechanistic process, i.e., a transition state with increased zwitter-ionic character in more polar solvents and electrocyclic process with an isopolar transition state in less polar solvents.

• The Journal of Engineering Geology
• /
• v.7 no.1
• /
• pp.37-52
• /
• 1997

This paper discribes the practical application of stability analysis on the revetment structures, and four different sections of revetment structures are considered in this study. As a result of stability analysis, the the section of inclined revetment with T.T.P. block shows the highest safety factor against to the sliding failure of cap concrete block, while the section of inclined revetment with rubble stone shows the highest safety factor against to the straight and circular sliding failure. And the safety factors are increased by increasing of the rigidity of covered materials and by decreasing of the slope angle. For the safety factor of overturnning and bearing capacity, the section of inclined revetment structures shows higher safety factors than the section of vertical structures, and the safety factors are increased by decreasing of the slope angle and by increasing of the bottom width of the structures.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.143-150
• /
• 1994

When the transverse bed slope ($S_t$) in channel bend is more than 0.1, it may produce undesirable results on the bed topography of the cross section. The linear relationship for $S_t$ results in zero or negative flow depths at the shallow $S_t$de of the cross section (i.e., inner bank). The exponential relationship for $S_t$ results in excessive flow depths at the deep side of the cross section (i.e., outer bank). This problem can be solved by combining the best features of both relationships described above. From the study, the linear relationship can be applied for the deep $S_t$de of the cross section. But the exponential relationship is suitable for the shallow side. Therefore, the new relationship of $S_t$ is clarified mathematically. A new mathematical model for bed topography is developed herein which takes accounts of the phase lag and the influence of the width to depth ratio. This model is used to analyze two sets of data: one from laboratory channel and the other from natural channel. A good agreement is found between the observed and the calculated bed topography based on the analysis of two sets of data.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.6 s.73
• /
• pp.35-40
• /
• 2006

In recent years, there's been strong demand for seawalls that havea gentle slope and permeability that serveswater affinity and disaster prevention from wave attack. The aim of this study is to examine wave transformation, including wave run-up that propagates on the coastal structures. A numerical model based on the weak nonlinear dispersive Boussinesq equation, together with the unsteady nonlinear Darcy law for fluid motion in permeable layer, is developed. The applicability of this numerical model is examined through Deguchi and Moriwaki's hydraulic model test on the permeable slopes. From this study, it is found that the proposed numerical model can predict wave transformation and run-up on the gentle slope with a permeable layer, but can't show accurate results for slopes steeper than about 1:10.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.7 no.1
• /
• pp.59-65
• /
• 1989

In this study, improvement of accuracy in a plain slope analysis is a main object using the bundle adjustment with changing the convergent angles and the configurations of control points when we can't take convergent case because of poor environment around establishment and cultural assets. From converged photographing using the angle of deviation, it was possible to improve accuracy in a plain slope analysis.

• Journal of the Korean association of regional geographers
• /
• v.3 no.2
• /
• pp.19-35
• /
• 1997

The purpose of this study is to find out the characteristics of landform in Geoje-Do using GIS and DTED data. The characteristics of landform in Geoje-Do are as follows; First, the height-range of Geoje-Do is $0{\sim}580m$, and the average elevation of it is 124m. Volcanic and granite region is mainly appeared at high elevation-region. But, we can't find out outstanding difference of elevation, according to its geology. The second. the slope-range of Geoje-Do is $0{\sim}52$ degree, and the average slope of it is 17.6 degree. The slope of volcanic and granite area is more steeper than any other region. But the results of analysis of the geology in Geojo-Do, don't show outstanding difference of the slope. The third, the area-rate of the aspect of Geoje-Do is almost same in all direction. And the area-rate of south-west direction is the highest. According to the geology of Geoje-Do, granite is distributed the most widely, and the area of volcanic and granite occupy 60% of entire island's area. According to analysis of influence of geology with elevation, geology has little relationship with elevation. According to analysis of geology and drainage network, streams are inclined to be developed well in Alluvium area. Drainage network is well developed throughout the entire island, except southeast area. The highest order of stream is 4 in 1:25,000 topographic map. The density of stream in Geoje-Do is very high, such as 1.6. The bifurcation-ratio of stream is also higher than 4 in all order. The length-ratio of stream is ranged from 1.24 to 3.25. According to the relationship between order and elevation. order is the greater, elevation is the lower. According to the relationship between order and slope, order is the greater, slope is the gentler. In this study, we use DTED Data, and compare it with topographic map data. According to the comparison, there is a little difference between DTED data and topographic map data. Therefore, to use DTED data in landform analysis, it is required coordinate matching process. This process is very important, and take very long time. Thus, if you use DTED in landform analysis, some processes are required. DTED data can be taken very easily, but its using is not simple. Because coordinate adjust is very hard work.