• The Transactions of The Korean Institute of Electrical Engineers
• /
• 제63권12호
• /
• pp.1661-1666
• /
• 2014

In this paper, a compact planar ultra wideband (UWB, 3.1~10.6GHz) multiple-input multiple-output (MIMO) antenna is proposed. This antenna consists of two monopole planar UWB antennas and T-shaped stub decoupling between two antennas. The T-shaped stub improve the isolation characteristic at the wide band. The evolution strategy(ES) algorithm is employed to optimized design. As a result, optimized antenna has a return loss less than -10dB and the isolation less than -15dB from 3.1GHz to 10.6GHz. During the optimization process, the antenna gain is enhanced at lower band and the envelope correlation coefficient(ECC) is lower than 0.003.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• 제22권4호
• /
• pp.35-40
• /
• 2022

This paper proposes an antenna that is located outside the PCB substrate of an electronic product to enable wireless communication in the ISM band. The PCB designed the T-shaped OPEN-STUB power supply line to be miniaturized so that it does not interfere with parts or interfere with design. The characteristics of the antenna were confirmed in the 2.4GHz and 5.8GHz bands using a T-shaped stub feeder and a spiral structure. The size of the antenna is 5mm in width × 6.5mm in length, and the thickness of the PCB is 1.2T. As a result of measurement of the manufactured antenna, it was possible to obtain a return loss of -10dB or more at 2.4GHz and 5.8GHz. In the E-plane, the gain was -4.45 dBi, and in the H-plane, the gain was -1.05 dBi. Therefore, the proposed small antenna for wireless communication showed excellent performance.

• The Journal of the Korea institute of electronic communication sciences
• /
• 제9권7호
• /
• pp.827-834
• /
• 2014

In this paper, a triple-band U-shaped monopole antenna with T-shaped stub for WLAN(Wireless Local Area Networks)/WiMAX(World interoperability for Microwave Access) applications. The proposed antenna is based on a planar monopole design, and composed of U-shaped of radiating patch, T-shaped strip in U-shaped, for triple-band operation. To obtain the optimized parameters, we used the simulator, Ansoft's High Frequency Structure Simulator(HFSS) and found the parameters that greatly effect antenna characteristics. Using the obtained parameters, the antenna is fabricated. The numerical and experiment results demonstrated that the proposed antenna satisfied the -10 dB impedance bandwidth requirement while simultaneously covering the WLAN and WiMAX bands. And characteristics of gain and radiation patterns are determined for WLAN/WiMAX application.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• 제35D권9호
• /
• pp.13-19
• /
• 1998

It was shown that the bandwidth of T-shaped microstripline fed slot antenna is wider than many of the conventional feeding structures. In this paper, we proposed a new method of enhancing the bandwidth of T-shaped microstripline fed slot antenna with a shunt open stub, and analyzed this antenna by using the FDTD method. We have computed waves and electric field distribution in the time domain, and VSWR, input impedance and radiation pattern in the frequency domaim by Fourier transforming the time domain results. It was found that the bandwidth of this antenna depend on the position(L$_1$) and length(L$_2$) of a shunt open stub. When these parameters are L$_1$=30 mm and L$_2$=33mm, we obtained the maximum bandwidth at the center frequency of 2.3 GHz. From the computed results, the optimum antenna is designed and fabricated. The fractional bandwidth of this antenna was 53.9 %. The measured results were in relatively good accordance with computed values.

• Steel and Composite Structures
• /
• 제34권3호
• /
• pp.347-359
• /
• 2020

The objective of this study is to experimentally scrutinize the axial performance of built-up concrete filled steel tube (CFT) columns composed of steel plates. In this case, the main parameters cross section types, compressive strength of filled concrete, and the effect of welding lines. Welded built-up steel box columns are fabricated by connecting two pieces of cold-formed U-shaped or four pieces of L-shaped thin steel plates with continuous penetration groove welding line located at mid-depth of stub column section. Furthermore, traditional square steel box sections with no welding lines are investigated for the comparison of axial behavior between the generic and build-up cross sections. Accordingly, 20 stub columns with thickness and height of 2 and 300 mm have been manufactured. As a result, welding lines in built-up specimens act as stiffeners because have higher strength and thickness in comparison to the plates. Subsequently, by increasing the welding lines, the load bearing capacity of stub columns has been increased in comparison to the traditional series. Furthermore, for specimens with the same confinement steel tubes and concrete core, increment of B/t ratio has reduced the ductility and axial strength.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• 제22권2호
• /
• pp.236-244
• /
• 2011

In this paper, we proposed flexible T-DMB dipole-shaped antenna that has strength of glass antenna and also has portability and ease of production. The input impedance of antenna according to vehicle body-effect was considered in order to install the antenna on the top of the front window. Installation position of on-glass antennas are changeable defends on driver, so we proposed Interdigital capacitor in feeding point to achieve matching characteristic with no position limit. The measurement result showed good return loss characteristic-below -6 dB in the T-DMB frequency band and maintained fixed resonant frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제13권7호
• /
• pp.3140-3145
• /
• 2012

In this paper, a design method for a compact slot antenna fed by a coplanar waveguide (CPW) is studied. A T-shaped tuning stub is inserted inside a narrow rectangular slot and the slot is impedance matched to the CPW feedline by adjusting the width, length, and position of the stub. The resonance frequency is adjustable by the slot length and the antenna size can be reduced by bending the slot. The resonance frequency and impedance matching property of the compact slot antenna are similar to those of the half-wavelength slot antenna, which enables one to design compact antenna of this type with ease. A compact slot antenna for 2.45-GHz ISM band is designed, fabricated on an FR4 substrate (dielectric constant of 4.4 and thickness of 0.8 mm), and experimentally tested. The measured results agree well with the simulations, which confirms the validity of this study. The fabricated compact slot antenna shows an impedance bandwidth of 200 MHz(2.32-2.52 GHz) for a VSWR < 2, which is suitable for 2.45-GHz ISM band (2.4-2.48 GHz). The measured radiation patterns show ${\infty}$-shaped directional pattern in the E-plane and nearly omni-directional pattern in the H-plane with a peak gain of 2.0 dBi, which are similar to those of a monopole antenna. The proposed antenna is expected to be suitable for the applications as antennas for WLAN, RFID, and mobile handset.

• ETRI Journal
• /
• 제33권6호
• /
• pp.981-984
• /
• 2011

A novel lowpass filter with a very sharp transition band and wide stopband is proposed. The proposed filter is based on T-shaped patches which are etched in symmetrical structures and folded open stub. To obtain a wide stopband, we have used stub loaded semi-circle stepped-impedance structures. By designing the resonator with high inductance and capacitance, a very sharp transition band is achieved. The proposed filter has a 3-dB cutoff frequency at 2.37 GHz and a 40-dB rejection at 2.44 GHz. The stopband with an attenuation level better than -13.2 dB is up from 2.4 GHz to 16 GHz, and consequently we have reached the high and wide rejection in stopband with compact size. Good agreements between the simulated and the measured results are presented.

• ETRI Journal
• /
• 제36권1호
• /
• pp.163-166
• /
• 2014

A microstrip dual-wideband bandpass filter using a multimode resonator (MMR) is proposed in this letter. The proposed MMR loaded with a T-shaped open-ended stub and a short-ended stub exhibits triple mode characteristics, and a synthesis method is developed to illustrate the wide passband with independently controllable center frequencies and bandwidths. To verify this design methodology, a dual-wideband filter with fractional bandwidths of 19.1% and 27.9% is designed and fabricated. The measured results agree with the simulations.

• ETRI Journal
• /
• 제33권6호
• /
• pp.953-956
• /
• 2011

A novel dual-mode bandpass filter (BPF) using a dual spiral-shaped defected ground waveguide (DGW) resonator is proposed in this letter. The dual-mode characteristic of this filter is achieved by loading a defected T-shaped stub at the midline of the spiral-shaped DGW resonator. Also, non-orthogonal input and output feed-lines are adopted in the filter. Based on the compact DGW structure, a dual-mode BPF with central frequency of 1.5 GHz for the global positioning system is designed, fabricated, and measured. Measured results agree well with the predicted response and verify the proposed methodology.