• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.264-264
• /
• 2010

Single-walled carbon nanotubes (SWCNTs) were grown on a Si wafer by using thermal chemical vapor deposition (t-CVD). We investigated the effect of the catalyst deposition rate on the types of CNTs grown on the substrate. In general, smaller islands of catalyst occur by agglomeration of a catalyst layer upon annealing as the catalyst layer becomes thinner, which results in the growth of CNTs with smaller diameters. For the same thickness of catalyst, a slower deposition rate will cause a more uniformly thin catalyst layer, which will be agglomerated during annealing, producing smaller catalyst islands. Thus, we can expect that the smaller-diameter CNTs will grow on the catalyst deposited with a lower rate even for the same thickness of catalyst. The 0.5-nm-thick Fe served as a catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. The catalyst layers were. coated by using thermal evaporation. The deposition rates of the Al and Fe layers varied to be 90, 180 sec/nm and 70, 140 sec/nm, respectively. We prepared the four different combinations of the deposition rates of the AI and Fe layers. CNTs were synthesized for 10 min by flowing 60 sccm of Ar and 60 sccm of $H_2$ as a carrier gas and 20 sccm of $C_2H_2$ as a feedstock at 95 torr and $810^{\circ}C$. The substrates were subject to annealing for 20 sec for every case to form small catalyst islands prior to CNT growth. As-grown CNTs were characterized by using field emission scanning electron microscopy, high resolution transmission electron microscopy, Raman spectroscopy, UV-Vis NIR spectroscopy, and atomic force microscopy. The fast deposition of both the Al and Fe layers gave rise to the growth of thin multiwalled CNTs with the height of ${\sim}680\;{\mu}m$ for 10 min while the slow deposition caused the growth of ${\sim}800\;{\mu}m$ high SWCNTs. Several radial breathing mode (RBM) peaks in the Raman spectra were observed at the Raman shifts of $113.3{\sim}281.3\;cm^{-1}$, implying the presence of SWCNTs (or double-walled CNTs) with the tube diameters 2.07~0.83 nm. The Raman spectra of the as-grown SWCNTs showed very low G/D peak intensity ratios, indicating their low defect concentrations.

• Korean Journal of Environmental Agriculture
• /
• v.10 no.2
• /
• pp.167-177
• /
• 1991

O-ethyl S-methyl ethylphosphonothioate [$LD_{50}$ (rat, oral) 4.6mg/kg ; $K_i$(bovine erythrocyte acetylcholinesterase) 303 $M^{-1\;min-1}$] was selected as a model compound to study the mode of action of O, S-dialkyl alkylphosphonothioates which have been hypothesized to be toxic via a bioactivation process. Two chemical oxidants, meta-chloroperoxybenzoic acid and monoperoxyphthalic acid, and rat liver microsomal oxidases were used to mimic the action of mixed function oxidases on the model compound. The formation of S-oxide, a very unstable active intermediate, was proposed based on the identification of metabolic products.Furthermore, a trapping experiment with ethanol showed that the unstable intermediate S-oxide had the ability to phosphorylate acetylcholinesterase which is an important enzyme in nerve systems. The S-oxide intermediates are presumed to be responsible for the toxicity of O,S-dialkyl alkylphosphonothioates.

• Korean Journal of Weed Science
• /
• v.14 no.1
• /
• pp.8-15
• /
• 1994

The mode of safening action and potency of the 1, 8-naphthalic anhydride(NA) were investigated in corn(Zea mays) and soybean(Glycine max) treated with herbicide bensulfuron[2-{{{{{(4,6-dimethoxy-2-pyrimidinyl)amino}carbonyl}amino}sulfonyl}methyl}benzoic acid] and imazaquin[2-{4,5-dihydro-4-methyl-4-(1-methylethyl)-5-oxo-1H-imidazol-2-yl} 3-quinolinonecarboxylic acid]. Seed dressing with 0.2%(w/w) NA showed successful protection in corn against injury from herbicide bensulfuron and imazaquin but not in soybean. Safening factors of NA against bensulfuron and imazaquin were 10.2 and 5.0, respectively, in corn, while they were both 1.3 in soybean. In vivo, Glutathione-S-transferase(GST) activity of NA-treated corn and soybean increased 1.8-and 1.3-fold, respectively, but the activity was not affected by the herbicides in vitro. Acetolactate synthase(ALS) levels of NA-treated corn was increased 1.3-fold, but not changed in soybean. Tolerance of ALS activity to the herbicides was slightly greater in ALS obtained from NA-treated corn than that from the untreated, whereas the difference was not found in soybean. A significant increase of ACCase due to NA occurred in corn, but not in soybean. The herbicides did not affect in vitro ACCase activity.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.93-101
• /
• 2008

Bearing strength test was investigated to determine the bearing properties of domestic larix glulam according to the load direction (in parallel to grain and in perpendicular to grain), the fastener (bolt and drift-pin), and the direction of laminae. The specimen was 5 ply glulam. The diameters of fastener are 12, 16 and 20 mm. The results were as follows. 1) In according to the diameter of bolt and drift-pin, the average of maximum bearing strength in parallel to grain loading was similar to that in perpendicular to grain loading. The average of maximum bearing strength was 1.50~2.31 times higher in parallel to grain loading than in perpendicular to grain loading. The average of maximum bearing strength in parallel to grain loading was lowered by 20% with increasing the diameter from 16 mm to 20 mm, but that in perpendicular to grain loading didn't show a clear tendency. 2) The average of bearing stiffness in parallel to grain loading was the highest at 16 mm in diameter. The average of bearing stiffness is similar to the shearing stiffness in drift-pin connection with increasing diameter. 3) In parallel to grain loading, the failure mode of specimens was the splitting along the grain in decreasing diameter. The failure mode in perpendicular to grain loading was the splitting along the grain. In this case, split occured more in specimens using bolt than in those using drift-pin. 4) The 5% offset yield strength in parallel to grain loading was similar to the predicted bearing strength of KBCS, NDS. In perpendicular to grain loading, the NDS's equation can be applied to predict the bearing strength.

• Journal of The Korean Association For Science Education
• /
• v.19 no.1
• /
• pp.29-40
• /
• 1999

The purpose of the present study was to test hypothesis that, because it uses tri-dimensional sensory pathway which have been showed a higher rate of neural activities than uni- or bi-dimensional's, lab-activity-based instruction is more effective teaching strategy in learning science than verbal-based instruction. In the present study, manipulative teaching strategy that uses visual, somatosensory and auditory information pathway was regarded as a mode of tri-dimensional sensory inputs. In addition, verbal teaching strategy that uses mainly auditory and a little visual information pathway was used as a mode of bi-dimensional sensory inputs. Fifty-six students who failed to successfully solve two proportional reasoning tasks (i.e., pouring water tasks) were sampled for this research from a junior high school. The subjects were randomly divided into a manipulative or a verbal teaching group, and given manipulative or verbal tutoring on the use of proportional reasoning strategies and a test of proportional reasoning during instruction. The results showed that manipulative group's performance on the test of proportional reasoning during instruction showed significantly higher performance than verbal group's (t=2.45, p<0.02). The present study also discussed some educational implications of the results.

• Korean Journal of Agricultural Science
• /
• v.40 no.2
• /
• pp.155-162
• /
• 2013

Genome-wide association study was performed on data from 266 Hanwoo steers derived from 66 sire using bovine 10K mapping chip in Hanwoo (Korean Cattle). SNPs were excluded from the analysis if they failed in over 5% of the genotypes, had median GC scores below 0.6, had GC scores under 0.6 in less than 90% of the samples, deviated in heterozygosity more than 3 standard deviations from the other SNPs and were out of Hardy-Weinberg equilibrium for a cutoff p-value of $1^{-15}$. Unmapped and SNPs on sex chromosomes were also excluded. A total of 4,522 SNPs were included in the analysis. To test an association between SNP and QTL, GWAS for five genetic mode (additive, dominant, overdominant, recessive and codominant) was implemented in this study. Three SNPs (rs29018694, ss46526851 and rs29018222) at a threshold p< $1.11{\times}10^{-5}$ were detected on BTA12 and BTA21 for dressing percentages in codominant and recessive genetic mode. The G allele for rs29018694 has 4.9% higher dressing percentage than A allele, while the T allele for ss46526851 has 2.57 % higher dressing percentage than C allele. Therefore, rs29018694 SNP showed a bigger effect than the other two SNPs (ss46526851 and rs29018222) in this study. In conclusion, this study identifies three loci with moderate effects and many loci with infinitesimally small effect across genome in Hanwoo.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.196-208
• /
• 2007

An analytical model is proposed for an optically controlled Metal Semiconductor Field Effect Transistor (MESFET), known as Optical Field Effect Transistor (OPFET) considering the diffusion fabrication process. The electrical parameters such as threshold voltage, drain-source current, gate capacitances and switching response have been determined for the dark and various illuminated conditions. The Photovoltaic effect due to photogenerated carriers under illumination is shown to modulate the channel cross-section, which in turn significantly changes the threshold voltage, drainsource current, the gate capacitances and the device switching speed. The threshold voltage $V_T$ is reduced under optical illumination condition, which leads the device to change the device property from enhancement mode to depletion mode depending on photon impurity flux density. The resulting I-V characteristics show that the drain-source current IDS for different gate-source voltage $V_{gs}$ is significantly increased with optical illumination for photon flux densities of ${\Phi}=10^{15}\;and\;10^{17}/cm^2s$ compared to the dark condition. Further more, the drain-source current as a function of drain-source voltage $V_{DS}$ is evaluated to find the I-V characteristics for various pinch-off voltages $V_P$ for optimization of impurity flux density $Q_{Diff}$ by diffusion process. The resulting I-V characteristics also show that the diffusion process introduces less process-induced damage compared to ion implantation, which suffers from current reduction due to a large number of defects introduced by the ion implantation process. Further the results show significant increase in gate-source capacitance $C_{gs}$ and gate-drain capacitance $C_{gd}$ for optical illuminations, where the photo-induced voltage has a significant role on gate capacitances. The switching time ${\tau}$ of the OPFET device is computed for dark and illumination conditions. The switching time ${\tau}$ is greatly reduced by optical illumination and is also a function of device active layer thickness and corresponding impurity flux density $Q_{Diff}$. Thus it is shown that the diffusion process shows great potential for improvement of optoelectronic devices in quantum efficiency and other performance areas.

• Imaging Science in Dentistry
• /
• v.39 no.3
• /
• pp.133-147
• /
• 2009

Purpose : To investigate the reproducibilities and compare the measurements in digital and MDCT-synthesized cephalometric radiograph, and to investigate the effect of head position on the measurement during imaging with MDCT. Materials and Methods : Twenty-two dry skulls (combined with mandible) were used in this study. Conventional digital cephalometric radiograph was taken in standard position, and MDCT was taken in standard position and two rotated position ($10^{\circ}$ left rotation and $10^{\circ}$ right tilting). MDCT data were imported in $OnDemand^{(R)}$ and lateral cephalometric radiograph were synthesized from 3D virtual models. Two types of rotated MDCT data were synthesized with default mode and with corrected mode using both ear rods. For all six images, sixteen angular and eleven linear measurements were made in V-$Ceph^{(R)}$ three times. Reproducibility of measurements was assessed using repeated measures ANOV A and ICC. Linear and angular measurements were compared between digital and five MDCT-synthesized images by Student t-test. Results : All measurements in six types of cephalometric radiograph were not statistically different under ICC examination. Measurements were not different between digital and MDCT-synthesized images (P>.05). Measurements in MDCT-synthesized image in $10^{\circ}$ left rotation or $10^{\circ}$ right tilting position showed possibility of difference from digital image in some measurements, and possibility of improvement via realignment of head position using both ear rods. Conclusion : MDCT-synthesized cephalometric radiograph can substitute conventional cephalometric radiograph. The error on head position during imaging with MDCT have possibility that can produce measurement errors with MDCT-synthesized image, and these position error can be corrected by realignment of the head position using both ear rods.

• Journal of Adhesion and Interface
• /
• v.2 no.2
• /
• pp.1-10
• /
• 2001

Silica for Epoxy Molding Compound (EMC) was coated via plasma-polymerization with RF plasma (13.56 MHz) as a function of treatment time, power and pressure. 1,3-diaminopropane, allylamine, pyrrole, 1,2-epoxy-5-hexene, allylmercaptan or allylalcohol were utilized for plasma polymerization coating and adhesion of coated silica was evaluated by measuring flexural strength. CTE and water absorption of EMC were also measured, and fracture surface of flexural specimen was analyzed by SEM in order to elucidate the failure mode. The plasma polymer coated silica was analyzed by FT-IR and reactivity of plasma polymer coating with epoxy resin was evaluated with DSC in order to investigate the adhesion mechanism. The EMC prepared from the silica coated with 1,3-diaminopropane or allylamine exhibited high flexural strength, low CTE, and low water absorption compared with the control sample, and also exhibited 100% cohesive failure mode. These results can be attributed to the chemical reaction between the functional groups in the plasma polymer coating and epoxy resin, and also consistent with the results from FT-IR and DSC analysis.

• Journal of Broadcast Engineering
• /
• v.13 no.2
• /
• pp.222-235
• /
• 2008

Recently, as growing of high definition media services like HDTV and IPTV, fast moving picture manipulation techniques need to meet what those services require. Especially, a fast reduced-size image extracting method is required in the areas of video indexing and video summary Conventional DC image extracting methods, however, can't be applied to H.264/AVC streams since a spatial domain prediction scheme is adopted in H.264/AVC intra mode. In this paper, we propose a theoretical method for extracting a thumbnail image from an H.264/AVC intra frame in the frequency domain. Furthermore, the proposed scheme can extract the thumbnail very fast since all operations are applied to transform coefficients directly, after a general equation for the thumbnail extraction in nine H.264/AVC intra prediction modes is introduced, an LUT(Look Up Table) for each mode is designed. Through the implementation and performance evaluation, while the subject quality difference between the output of our scheme and a conventional output is negligible, the former can extract the thumbnail faster then the latter by up to 63%.