• Structural Engineering and Mechanics
• /
• 제32권3호
• /
• pp.447-457
• /
• 2009

A general analytical method for computing the joint stiffness from the sectional properties of the members that form the joint is derived using Vlasov's thin-walled beam theory. The analytical model of box T-joint under out-of-plane loading is investigated and validated using shell finite element results and experimental data. The analytical model of the T-joint is implemented in a beam finite element model using a revolute joint element. The out-of-plane displacement computed using the beam-joint model is compared with the corresponding shell element model. The results show close correlation between the beam revolute joint model and shell element model.

• 해양환경안전학회지
• /
• 제21권6호
• /
• pp.778-783
• /
• 2015

본 연구는 해상에서의 안전사고의 경감과 국민의 생명을 보호하기 위한 목적으로 자체 연구를 수행하여 FRP의 수리공법인 Butt Joint, Lap Joint, V-Scarf Joint(12t, 16t, 20t), X-Scarf Joint(12t 16t, 20t)의 인장강도와 굽힘강도를 통해 이음방식에 따른 구조강도 특성을 실험하였다. 이음 방법에 따른 인장강도와 굽힘강도의 시험편을 종합 분석한 결과, 인장강도의 강도와 굽힘강도의 그래프 패턴은 비슷한 양상으로 증가와 감소를 하였으며, 인장강도와 굽힘강도 모두 X-Scarf-Butt Joint-V-Scarf-Lap Joint 순으로 강도가 우수하였다. 인장강도는 강도특성이 가장 우수한 X-Scarf라 하더라도 Basic Material의 57% 수준의 강도를 나타내었고 굽힘강도는 X-Scarf가 Basic Material의 77% 수준의 강도를 나타내었다. 종합적으로 Over-Lay 구분을 포함하여 X-Scarf 12t 이음이 인장강도, 굽힘강도 특성이 우수하였으며 Lap Joint가 가장 좋지 않았다. Scarf 이음시 Taper 길이에 따른 강도의 차이는 V-Scarf 이음은 Taper의 길이가 가장 큰 20t가 인장강도, 굽힘강도 특성이 우수한 반면 X-Scarf 이음은 Taper의 길이가 가장 짧은 12t가 인장강도, 굽힘강도 특성이 우수하여 상반되는 결과를 나타내었다. 선박에는 많은 Stress가 작용하여 시험편만을 가지고 실험한 본 연구와 직접적인 비교는 힘들지만, 재료의 가장 기본 특성을 인장강도와 굽힘강도 시험을 통해 확인할 수 있다. FRP 국부적인 수리 방법인 Butt Joint, Lap Joint, V-Scarf, X-Scarf 4가지의 이음방법에 따른 시험값과 모재 대비 감소되는 비율을 제시하였고 추가적으로 V-Scarf와 X-Scarf의 Taper 길이별 특성을 12t, 16t, 20t로 구분한 결과값을 제시함으로써 수리 현장에서의 위치별 특성에 맞는 수리 방법의 응용이 가능하도록 하였다.

• 한국군사과학기술학회지
• /
• 제11권4호
• /
• pp.149-158
• /
• 2008

This article provides strength estimation of T-joint area which made of composite material. Inner and outer structures of medium range surveillance radar are all made of sandwich structure which is made with composite material(CFRP) and aluminum honeycomb core. Since the radar is voluminous and has very complex inner structure, the whole structure cannot be made as one piece. Therefore, usage of T-joints is inevitable. Since some of stress concentration areas were located around T-joint area, series of strength estimations were conducted. Three different configurations were tested to improve mechanical properties(primarily on strength). The results show an improvement on strength to meet calculated strength on stress concentrated T-joint area.

• 한국해양공학회지
• /
• 제13권2호통권32호
• /
• pp.51-57
• /
• 1999

In this study, one side fillet welded T-joint, used in box type girder and other welding structure, was investigated by stress analysis and bending fatigue test without edge preparation, with variation of joint shape. The purpose of this study is to give the welding condiltion and design standard on manufacturing one side fillet welded T-joint. As a result, the following conclusions were obtained. 1) In one side fillet welded T-joint, the larger the leg length and the penetration depth, the greater the bending fatigue strength because reduction of stress and strain on toe and root. The increase of the longitudinal leg length rather than vertical leg length contributed to the increase in bending fatigue strength. 2) In one side fillet welded T-joint without edge preparation, both general manual welding and general automatic welding were carried out with same condition. In this case, automatic welding showed deeper penetration and more increased longitudinal leg length than manual welding, so that automatic welding offers greater bending fatigue strength. 3) For one side fillet welded T-joint without edge preparation with automatic welding, the ratio(h/t) of the leg length(h) and the main plate thickness(t) in which toe crake can occur was 1.0 over.

• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.134-141
• /
• 1998

In this study, a fillet size for bending fatigue strength of one side fillet welded T-joint, used in box type girder and other welding structure, was investigated by bending fatigue test with or without edge preparation and burn through, with variation of joint shape. As a result, the following conclusions were obtained. (1) In one side fillet welded T-joint, the larger the leg length, the greater the bending fatigue strength. The increase in bending fatigue strength. (2) One side filet welded T-joint with edge preparation showed higher bending fatigue strength than that with twofold-large leg length and without edge preparation. (3) In one side fillet welded T-joint without edge preparation, both manual welding and automatic welding were carried out with same condition. In this case, automatic welding shoed deeper penetration and more increased horizontal leg length than manual welding, so that automatic welding offers grater bending fatigue strength. (4) For one side fillet welded T-joint without edge preparation, the ratio(h/t) of the leg length (h) and the main plate thickness (t) in which toe crack can occur was 1.2 over. (5) In one side fillet welded T-joint with edge preparation, the burn through led to reduced bending fatigue strength. However, this bending fatigue strength was higher than that of one side fillet welded T-joint without edge preparation and with a larger leg length.

• Composites Research
• /
• 제31권5호
• /
• pp.238-245
• /
• 2018

수압램 현상은 전투용 항공기의 주요 전투 손상 중 하나이며, 항공기 기체 생존성 평가에 중요한 영향을 미친다. 수압램 효과는 유체-구조물간의 상호관계를 통하여 나타나며, 구조물의 동적 변형률을 측정하여 파손 거동 및 파손 여부를 확인할 수 있다. 본 논문에서는 수압램 현상을 모사할 수 있는 수압램 시험 장치를 이용하여 수압램에 의한 복합재 T-Joint의 파손 시험을 수행하였다. 또한 계측기기의 입력 정전용량과 시간 상수 확인을 위해 PVDF 센서 보정 시험을 수행하였다. 복합재 T-Joint에 스트레인 게이지와 전하증폭기를 사용하지 않은 PVDF 센서를 부착하여 수압램 현상에 의한 복합재 T-Joint의 동적 변형률을 측정하였다. PVDF 센서와 스트레인 게이지의 동적 변형률을 이용하여 복합재 T-Joint의 파손 거동 및 파손 여부를 확인하였다.

• Journal of Welding and Joining
• /
• 제19권2호
• /
• pp.215-220
• /
• 2001

In the T-joint welding, the complete penetration joint which is obtained by groove welding with edge preparation is generally required thor the safety and reliability of structures but this way have the some defects such as increase of working time, consumed welding electrode quantity and large welding deformation. If there is no probrem, in the strength, T-joint welding without edge preparation will be profitably understood in the economical and welding deformation side. In this paper, we performed the finite element analysis to understand the characteristics of welding residual stresses on two models, complete penetration joint have the edge preparation and incomplete penetration joint without edge preparation, respectively. Especially, we observed the relation between welding residual stress distributed on the notch of gap in the root and external force in the incomplete penetration joint without edge preparation.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2334-2343
• /
• 2000

This paper proposes an efficient beam-shell modeling technique for the free vibration analysis of a T-joint thin-walled beam structure. Except a small portion of a T-joint which is modeled by shell elements, the structure is modeled by thin-walled beam elements that can describe warping and distortion. In order to match the shell and thin-walled beam elements at the interface of the dissimilar elements, a technique based on a pseudo inverse matrix is formulated. This paper also examines the role of the thin-walled element taking into account the distortion and warping deformation degrees of freedom in predicting accurately the dynamic characteristics of a T-joint thin-walled structure.

• 한국응용과학기술학회지
• /
• 제37권2호
• /
• pp.224-231
• /
• 2020

본 연구의 목적은 유도 허벅다리걸기 기술 발휘 시 발목 관절의 테이핑 처치가 하지 관절과 압력중심(COP, center of pressure)에 미치는 영향을 분석하는데 있었다. 대학 유도 선수 20명(연령, 20.9±0.8세; 신장, 168.6±7.4cm; 체중, 73.5±11.6kg; 신체질량지수, 25.7±2.6kg/㎡)이 참여하였으며, 발목 관절 테이핑 처치 전과 후의 2가지 조건에서 허벅다리걸기 기술 발휘 시 지지다리 관절의 각도와 압력중심 요인을 분석하여 다음의 결과를 도출하였다. E2(t=2.411, p=.027) E4(t=2.388, p=.029)시점에서 발목 관절의 각도는 테이핑 처지 전에 비해 처치 후 발목의 각도가 통계적으로 적은 수치를 나타내었고, E2(t=-2.343, p=.032) E3(t=-4.531, p=.000)시점에서 힙 관절의 각도는 통계적으로 크게 나타났다. 그리고 발목 관절 테이핑 처치 후 좌·우의 COP 이동은 상대를 메치는 P3 국면에서 통계적으로 크게 나타났으며(t=2.670, p=.016), 전·후의 COP 이동은 상대의 무게 중심을 기울이는 P1 국면에서 통계적으로 적은 수치를 나타내었다(t=2.846, p=.011). 그러므로 허벅다리걸기를 특기로 사용하는 유도 선수들은 발목 관절 테이핑으로 인해 발생하는 지지관절의 운동 기능과 COP의 이동범위를 고려하여 사용하는 것에 대하여 제안하고자 한다.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.56-65
• /
• 1998

The bonding strength evaluation of the light weight materials for an electrical vehicle has been performed through the T-peel joint test in which the design paramete- rs such as joint style, adherend type, adherend thickness, adhesive thickness, and adhesive type are considered. It is experimentally observed that the peel strength of joint increases with the increase of the adherend thickness. With the increase of the adhesive thickness, however, the peel strength of joint increases a little. Aluminum-FRP adherend combination shows such higher peel strength than that of Aluminum-Aluminum adherend combination. For the adhesive bonded joint, the results of FEM analysis agree with those of experiment. The adhesive bonded joint reinfored with a rivet gives higher peel strength than that of the joint without rivet.