• 한국초전도ㆍ저온공학회논문지
• /
• 제10권1호
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• 한국초전도ㆍ저온공학회논문지
• /
• 제8권1호
• /
• pp.65-70
• /
• 2006

Transient heat transfer caused by an impulsive heating in subcooled liquid nitrogen is investigated experimentally. This study is part of out ongoing efforts directed to a stable cryogenic cooling system lot superconducting fault current limiters (SFCL). A thin heater attached by epoxy on one surface of a GFRP plate is immersed in liquid-nitrogen bath at temperatures between 77 K and 55 K. A strong heat flux up to $150W/cm^2$ is generated lot 100 ms, and the temperature of the heater sulfate is measured as a function of time. The behavior of bubbles on the heating surface can be explained by comparing the measured temperature history for vertical and two horizontal (up and down) orientations. It is concluded that the subcooling of liquid nitrogen below 70 K is very effective in suppressing bubbles, resulting in better thermal protection and faster recovery from an impulsive heat.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.439-443
• /
• 2008

We investigate the mechanical behavior of a pre-heat treated steel of ESW95, which is being used for automotive parts including tie-rods to save manufacturing cost and enhance product quality. SCM435 is also investigated to reveal the characteristics of the pre-heat treated steel tested. AFDEX/MAT is used to extract the true stress-strain curve over the large strain with higher accuracy. It has been found that ESW95 has very week strain-hardening behavior which can be negligible compared with SCM435 and that the initial yield strength is quite high and the toughness of ESW95 reaches nearly 75% of SCM435. ESW95 is characterized by the weak strain-hardening behavior and high yield strength that can be lead to minimization of post-processing including heat treatment and straightening. ESW95 and SCM435 are also compared by applying them to ball-stud forging by computer simulation. It is expected that a great deal of change may take place in production as well as in service if the pre-heated steels are adopted.

• 한국수소및신에너지학회논문집
• /
• 제10권2호
• /
• pp.131-139
• /
• 1999

The objective of this works was to synthesize the$Mg_2Ni$ hydrogen storage materials economically and to eliminate the intial activation process. $Mg_2NiH_x$ was mechanically alloyed under purified hydrogen gas atmosphere using pure Mg and Ni chips. M.A(Mechanical Alloying) was carried out using planetary ball mill for times varying from 12h to 96h under 20bars of hydrogen gas pressure. $Mg_2NiH_x$ started to form after 48h and the homogeneous $Mg_2NiH_x$ composites was synthesized after 96h. From TG analysis, the dehydriding reaction of $Mg_2NiH_x$ started at around $200^{\circ}C$. The result of P-C-T at $300^{\circ}C$ revealed the hydrogen storage capacity of $Mg_2NiH_c$ reached 3.68 wt% and the effective hydrogen storage was 2.38 wt%. The enthalpy difference of absorption-desorption cycling for the hydride formation and the hysteresis were reduced and the plateau flatness and the sloping were improved according to M.A time.

• 한국강구조학회 논문집
• /
• 제9권2호통권31호
• /
• pp.249-257
• /
• 1997

본 연구에서는 호안의 안벽 및 방파제의 조성에 있어 기존의 타공법에 비해 경제성, 공사기간 및 시공장비 측면에서 유리한 거치식 강판셀 공법의 설계 기법 및 구조적 건전성 확보를 위해 실시한 실험 연구 결과를 제시하였다. 강판셀 구조는 다수의 보강재와 셀-아크 연결부 등이 존재하는 얇은 쉘 구조로서 그 거동이 복잡할 뿐만 아니라 설계 기준에서 셀 및 아크 내부의 속채움 토압의 크기가 다소 모호하게 규정되어 있다. 이러한 문제의 해결을 위해 실규모의 원통형 단면벽 강판셀 구조$(D11.0^m{\times}H14.0^m{\times}12t)$를 설계 제작하여 해상에 거치하고 속채움을 한 후 현장 응력계측을 수행하였으며, 그 결과를 상세 구조해석 결과와 비교 분석함으로써 당 공법의 설계 기술을 구축하고자 하였다.

• Computers and Concrete
• /
• 제10권4호
• /
• pp.419-434
• /
• 2012

This paper presents a finite element (FE) model for predicting the nonlinear response and behavior of a reinforced concrete T-beam deficient in shear under cyclic loading. Cracking loads, failure loads, response hysteresis envelopes and crack patterns were used as bench mark for comparison between experimental and FE results. A parametric study was carried out to predict the optimum combination of the open and close crack shear transfer coefficients (${\beta}_t$ and ${\beta}_c$) of the constitutive material model for concrete. It is concluded that when both shear transfer coefficients are equal to 0.2 the FE results gave the best correlation with the experimental results. The results were also verified on a rectangular shear deficient beam (R-beam) tested under cyclic loading and it is concluded that the variation of section geometry has no effect on the optimum choice of the values of shear transfer coefficients of 0.2. In addition, a parametric study based on the variation of concrete compressive strength, was carried out on the T-beam and it is observed that the variation of concrete compressive strength has little effect on the deflection. Further conclusions and observations were also drawn.

• 소성∙가공
• /
• 제17권7호
• /
• pp.507-510
• /
• 2008

Effect of V addition on the precipitation behavior and strength of Fe-36Ni based high strength Invar alloy for power transmission wire was investigated. Fe-36Ni Invar alloy plates were fabricated using conventional ingot casting followed by hot rolling. High strength can be obtained through precipitation hardening and strain hardening by cold rolling. Simulation using FactSage$^{(R)}$ revealed that equilibrium phases which can be formed are two kinds of MC-type precipitates, $Mo_{2}C$ and $M_{23}C_6$ carbide. The latter stoichiometric carbide was expected to be formed at relatively lower temperature of $800^{\circ}C$.

• 접착 및 계면
• /
• 제10권2호
• /
• pp.84-89
• /
• 2009

The objective of this research was to investigate the curing behavior and adhesion performance of urea-melamine-formaldehyde (UMF) resin for the four types of UMF-1, UMF-2, UMF-3, and UMF-4 which synthesized by the staged addition of melamine. Also, various network structures of these resin types were discussed based on their different curing behavior and adhesion performance. The curing behavior was evaluated by DMTA and thermal stability was checked by TGA. Adhesion performance was evaluated by dry and wet shear strengths and the pH value of each cured resin was checked to see its effect on the adhesion performance. The results indicated that the UMF-1 resin type by the addition of melamine initially with the urea and formaldehyde at the same F/(U+M) rate showed the lowest thermal stability, rigidity (${\Delta}E^{\prime}$), temperature of tan ${\delta}$ maximum ($T_{tan}\;_{\delta}$), and wet shear strength, and pH value of cured resin. In wet shear strength, however, the UMF-4 resin type appears to be slightly higher than UMF-1 resin type.

• 소성∙가공
• /
• 제28권2호
• /
• pp.98-104
• /
• 2019

The present study numerically simulates the deformation heterogeneity developed in AA1100 during multi-axial diagonal forging (MADF) using finite element analysis (FEA). Diagonal forging type consisting of diagonal forging (DF) and return-diagonal forging (R-DF) proved to be relatively beneficial compared to plane forging type which includes plane forging (PF) and return-plane forging (R-PF) for minimizing the non-uniformity of deformation developed in workpieces. Simulation of the effective strain generated in workpieces during the two types of forging was done using 3-D FEA. FEA shows the effect of friction coefficient on the deformation behavior on workpieces. The simulation of 2 types forging with different friction coefficients revealed that the magnitude of barreling effect and strain heterogeneity in workpieces increases with an increase in the friction coefficient.

• 소성∙가공
• /
• 제30권3호
• /
• pp.134-141
• /
• 2021

In order to improve excessive spring-back behavior as a result of the roll forming process using ultra high strength steel (UHSS) sheet, local softening in region of a partial area expected to be deformed on an initial blank is considered in this study. With SPFC1470 UHSS sheet with initial blank thickness of 1.20mm, the local softening is performed with the following conditions: temperatures of 500℃, 550℃, 600℃ and 650℃, and holding time of 20s, 40s, 80s and 160s. Mechanical properties, such as yield stress and tensile strength, as well as elongation, are evaluated through uniaxial tensile tests, while the microstructural characteristics as a result of local softening are also investigated using the heat-treated specimens. As a result, it is shown that the spring-back behavior of the roll-formed prototype was reduced about by 78.9%, when the local softening at about 500℃ was performed for 160s considering the practical manufacturing condition.