• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04c
• /
• pp.115-118
• /
• 2008

A field-oriented UHF system for on-line PD monitoring of transformers. is designed, which has been installed inside the oil tank of a transformer by two ways: on-line installing mode through the oil-valve and pre-installing mode through the man hole/hand hole cover. This system has successfully captured long intermittent discharge signals that hadn't been detected through conventional techniques, and solved the problem successfully. The results demonstrate that UHF technique has great advantages for on-line PD monitoring of transformers. By adopting the peak detection technique, it becomes easy and effective for the transplantation of the phase-resolved pattern recognition technique from conventional method to UHF method, and then to realize continuous on-line monitoring, source characterization and trending analysis.

• Journal of Korea Multimedia Society
• /
• v.9 no.12
• /
• pp.1628-1635
• /
• 2006

A new frequency-modulated m-sequence correlation technique was described. It has. been seen that the frequency modulation scheme leads to higher signal-to-noise ratio than direct sequencing and less hardware effort than PSK modulation scheme. The operating frequency of the correlation system was deduced. The optimal frequency for the frequency-modulated m-sequence correlation system should be 1.35 times of the center frequency of the transducer. The application of this correlation technique to electromagnetic ultrasonic system was computer-simulated.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1624-1627
• /
• 2005

We proposed a design technique for auto-landing guidance and control system. This technique utilizes linear controller and neural network. Main features of this technique is to use conventional linear controller and compensate for the error coming from the model uncertainties and/or reference model mismatch. In this study, the multi-perceptron neural network with single hidden layer is adopted to compensate for the errors. Glide-slope capture logic for auto-landing guidance and control system is designed in this technique. From the simulation results, it is observed that the responses of velocity and pitch angle to commands are fairly good, which are directly related to control inputs of throttle and elevator, respectively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.597-604
• /
• 1995

When a pipe bend is modelled with straight beam elements, its stiffness, particularly in bending behavior, is overestimated than its true value. In this paper, we propose a simple and practical beam-modelling technique to estimate its stiffness properly. When this technique, based on the strain energy concept, is employed to modify the beam sectional properties of the bend, quite satisfactory results can be obtained. To verify the validity of this method, we apply the present technique to the free vibration analysis of a center pipe with 2 bends, one of the three components of the automobile exhaust system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.413-419
• /
• 1998

A novel order-reduction technique for model predictive control(MPC) is proposed based on the singular value decomposition(SVD) of a pulse response circulant matrix(PRCM) of a concerned system. It is first investigated that the PRCM (in the limit) contains a complete information of the frequency response of a system and its SVD decomposes the information into the respective principal directions at each frequency. This enables us to isolate the significant modes of the system and to devise the proposed order-reduction technique. Though the primary purpose of the proposed technique is to diminish the required computation in MPC, the clear frequency decomposition of the SVD of the PRCM also enables us to improve the robustness through selective excitation of frequency modes. Performance of the proposed technique is illustrated through two numerical examples.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.3
• /
• pp.950-956
• /
• 2014

Special purpose sensor design using MEMS (Micro-Electro-Mechanical Systems) technique is commonly used in Nondestructive Testing (NDT) research for the evaluation of existing structures and for the safety control and requirements. Various sensors and network have been developed for general infrastructures as well as safety-critical applications, e.g., aerospace, defense, and nuclear system, etc. In this paper, one of sensor technique using Fiber Bragg Gratings (FBG) and Finite Element Method (FEM) evaluation is discussed. The experimental setup and data collection technique is also demonstrated. The factors influencing test result and the advantages/limitations of this technique are also reviewed using various methods.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.1016-1023
• /
• 2013

Predictive current control offers the potential for achieving more precise current control with a minimum of distortion and harmonic noise. However, the predictive method is difficult to implement and has a greater computational burden. This paper introduces a theoretical analysis and experimental verification for an improved predictive current control technique applied to single phase grid connected voltage source inverters (VSI). The proposed technique has simple calculations. An ATmega1280 microcontroller board is used to implement the proposed technique for a simpler and cheaper control system. To enhance the current performance and to obtain a minimum of current THD, an improved tri-level PWM switching strategy is proposed. The proposed switching strategy uses six operation modes instead of four as in the traditional strategy. Simulation results are presented to demonstrate the system performance with the improved switching strategy and its effect on current performance. The presented experimental results verify that the proposed technique can be implemented using fixed point 8-bit microcontroller to obtain excellent results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.1
• /
• pp.42-48
• /
• 2006

In this study, a repetitive response surface enhancement technique (RRSET) is proposed as a new system approximation method for the efficient multidisciplinary design and optimization (MDO). In order to represent the highly nonlinear behavior of the response with second order polynomials, RRSET introduces a design space transformation using stretching functions and repetitive response surface improvement. The tentative optimal point is repetitively included to the set of experimental points to better approximate the response surface of the system especially near the optimal point, hence a response surface with significantly improved accuracy can be generated with very small experimental points and system iterations. As a system optimizer, the simulated annealing, which generates a global design solution is utilized. The proposed technique is applied to several numerical examples, and demonstrates the validity and efficiency of the method. With its improved approximation accuracy, the RRSET can contribute to resolve large and complex system design problems under MDO environment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.50-56
• /
• 2010

This paper presents a new design algorithm for piece-removing dynamical system, based on 6-Sigma DMADOV technique using ARIZ and Brainstorming. Our design target is the piece-removing system installed on a mobile platform of bead-grinding equipment. The 6-Sigma DMADOV technique guides us design process according to 6 steps, i.e., Define - Measure - Analyze - Design - Optimize - Verify. A Design strategy to reduce the weight of piece-removing dynamical system will be explored by using ARIZ, i.e.,(the abbreviation of Algorithm for Inventive Problem Solving in Russian). The ARIZ will result in a final solution that the height and angle control parts for a cutting tool should be replaced by a kinematical approach, rather than complicated mechatronic approach(using motors). The Optimize step is composed of two sub-steps: (i) Generating process for obtaining several ideas of piece-removing system by using Brainstorming technique, satisfying the final solution derived from the Design step using ARIZ, and (ii) Optimizing process for selecting the most optimal idea of piece-removing system by using Pugh's matrix from the viewpoints of weight, cost and accuracy. The laststep of Verify has shown that the final design obtained by the 6-Sigma DMADOV technique with ARIZ & Brainstormingcan improve an initial design with design requirements satisfied. In this paper, we have shown that ARIZ and Brainstorming can be cooperatively merged into 6-Sigma DMADOV to give us both a formulatedproblem-solving approach and diverse candidate solutions(or ideas) without trial-and-error efforts.

• Proceedings of the IEEK Conference
• /
• 2000.11d
• /
• pp.207-210
• /
• 2000

We propose a content based watermarking technique in multimedia management system. In the proposed technique, a content description technique of MPEG-7 for the multimedia database is adopted into a watermarking technique. With multimedia features described by MPEG-7 standard, we propose a novel watermarking technique where MPEG-7 descriptors are regarded as perceptually significant portions. The watermark is embedded in cooperating with multimedia features such as MPEG-7 descriptor. To verify the feasibility and performance of proposed watermarking technique, experiments with the MPEG-7 database are performed.