• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.3
• /
• pp.133-142
• /
• 2014

Recently, more focus is shift to imbalances in aggregate market supply and demand and an exhaustion of natural resources. In this situation, Electric arc furnace oxidizing slag (EAF Slag) has high application possibility as aggregate for concrete due to similar property with general aggregate. In this study, We've got the plan to assure the chemical stability of EAF Slag, and then experimentally tested the mechanical performance and durability for the fine aggregate used EAF Slag. On this test result, we suggest the application plan. At the result of this study, it shows that EAF slag would reduce the surface defect such as pop-out due to natural aging for the fixed hour and adjustment the grain size of EAF Slag. And mechanical performance and durability according to the replacement rate of concrete service, were revealed more than equal or equal compare to general aggregate. Hereafter, quality control must precede not to impede the beauty of concrete surface as assure the safety for aging and processing. And, to establish the environmental resource recycling system for by-products of steel, it should be made development of various application and guideline of quality control for the EAF slag aggregate. Moreover, it must be constantly studied all kind of engineering performance and durability for related to this study.

• Journal of Wetlands Research
• /
• v.22 no.4
• /
• pp.295-301
• /
• 2020

This research analyzed the relationship between environmental factors and the density of Sycios angulatus in the Miho Stream, Geum River water system in order to secure basic data for the control of the ecosystem-distrubing plant Sycios angulatus. As a result of the soil particle size analysis of Sycios angulatus habitat, it was found that the density of Sycios angulatus decreased as the silty and clay contents increased. Most of the Sycios angulatus habitats had high sandy and silt content, and low clay content of less than 2%. The increased flow rate reduced the density of Sicyos angulatus. This is because when the flow rate is increased, the Sicyos angulatus cannot grow due to the change in soil characteristics. Water quality plays a role in supplying nutrients when Sicyos angulatus are submerged. However, due to the change in soil characteristics during flooding, the density of Sicyos angulatus tended to decrease due to impaired growth. The Sicyos angulatus can be managed through artificial and natural techniques. The appropriate natural control technique is the creation of a natural waterway in the habitats to change the water contents.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5D
• /
• pp.437-444
• /
• 2012

This study intended to improve traffic safety in work zones using fluorescent orange color traffic signs. For this end, the current problems of existing traffic signs and facilities in work zones were analyzed and some good examples of foreign countries were compared. More specifically, in order to identify current problems, the basic shape and color of traffic signs in use were examined through literature review, surveys and field studies. It was found that the fluorescent color worked more effectively than other colors in terms of visibility and conspicuity in work zone sign system. For evaluation, both Conspicuity surveys and in-door simulator experiments were conducted to effectively assess the merits and demerits of different types of traffic signs for work zones. The results of evaluations showed that black lettering on a fluorescent orange background outperformed more than 70% in terms of visibility and ability to call drivers' attention compared with those from black/red lettering on yellow/white backgrounds currently used at work zones on expressways and national highways. In addition, simulated driving experiment disclosed that drivers recognized the fluorescent orange background sign 15m ahead compared with the yellow background sign and 25m ahead compared with the white background sign, respectively. As for the diamond-shaped "Under Construction" sign, drivers recognized fluorescent orange background 11m ahead compared with the yellow background sign and 19m ahead compared with the white background sign, respectively.

• KIPS Transactions on Software and Data Engineering
• /
• v.2 no.8
• /
• pp.571-578
• /
• 2013

The IHO S-100 is a standard on the universal hydorgraphic data model for supporting information services that integrate various data in maritime and provide proper information for safety of vessels. The S-100 is used to develop S-10x product specifications which are standards on guideline for creation and delivery of specific data set in maritime. The product specification for feature-based data such as ENC(Electronic Navigational Chart) data includes a feature catalogue that describes characteristics of features in that feature-based data. The feature catalogue is developed by domain experts with knowledge on data of the target domain. However, it is not feasible to develop a feature catalogue according to the XML schema by manual. In the IHO TSMAD committee meeting, needs of developing technology on building feature catalogue has been discussed. Therefore, we present a feature catalogue builder that is a GUI(Graphic User Interface) system supporting domain experts to build feature catalogues in XML. The feature catalogue builder is developed to connect with the FCD(Feature Concept Dictionary) register in the IHO(International Hydrographic Organization) GI(Geographic Information) registry. Also, it supports domain experts to select proper feature items based on the relationships between register items.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.05a
• /
• pp.147-154
• /
• 2005

The ship plating is generally subjected to combined in-plane load and lateral pressure loads. In-plane loads include axial load and edge shear, which are mainly induced by overall hull girder bending and torsion of the vessel. Lateral pressure is due to water pressure and cargo. These load components are not always applied simultaneously, but more than one can normally exist and interact Hence, for more rational and safe design of ship structures, it is of crucial importance to better understand the interaction relationship of the buckling and ultimate strength for ship plating under combined loads. Actual ship plates are subjected to relatively small water pressure except for the impact load due to slamming and panting etc. The present paper describes an accurate and fast procedure for analyzing the elastic-plastic large deflection behavior up to the ultimate limit state of ship plates under combined loads. In this paper, the ultimate strength characteristics of plates under axial compressive loads and lateral pressure loads are investigated through ANSYS elastic-plastic large deflection finite element analysis with varying lateral pressure load level.

• Proceedings of KOSOMES biannual meeting
• /
• 2005.05a
• /
• pp.141-146
• /
• 2005

Ship have cutout inner bottom and girder and floor etc. Ship's structure is used much, and structure strength must be situated, but establish new concept when high stress interacts sometimes fatally the area. There is no big problem usually by aim of weight reduction, a person and change of freight, piping etc. Because cutout's existence grow up in this place, and, elastic buckling strength by load causes large effect in ultimate strength. Therefore, stiffened perforated plate considering buckling strength and ultimate strength is one of important design criteria which must examine when decide structural concept at initial design. Therefore, and, reasonable buckling strength about perforated stiffened plate need to ultimate strength limited design . Calculated ultimate strength varied several web height and cutout's dimension, and thickness in this investigated data. Used program(ANSYS) applied F.E.A code based on finite element method.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.05a
• /
• pp.15-20
• /
• 2007

In this study, the authors investigated the change of marine environment by dumping dredged materials generated by construction of Busan New Port. There are lots of possibilities to impact an ocean ecosystem by toxic materials in the dredged material dumped in the open seas. As a result of analysis of environmental monitoring in the study areas 12 times a year, COD is II grade, T-N is I grade, T-P is between II and III grade. This result is same as another results of offshore in Korea. It seems unclear that it results from the change of water quality by dumping dredged material. However, according to the result of this investigation, it is not effected extensively to the marine environment by dumping dredged materials. We need further environmental monitoring in the interest sea areas, also need to keep on investigating the impact on the marine ecosystem by dumping dredged materials.

• Journal of Navigation and Port Research
• /
• v.31 no.1 s.117
• /
• pp.1-6
• /
• 2007

The evaluation of safety of simulated maneuvers is frequently analysed by so called goal-line or point of interest in Korea. For the purpose of warning the risk in the proximity measure composed of only the goal-line analysis, this paper utilized Korea Institute of Maritime and Fisheries Technology(KIMFT) which houses a real-time, full-mission shiphandling simulator to examine the goal-line and in-length analyses in the outbound channel of Kwangyang port as an example. It used a 15,000 TEU container ship as a model under environmental conditions of the northwestly 26-knot wind and 2.2-knot ebb current. The result of two analyses showed the probability invading the channel boundary obtained by the goal-line analysis is a little greater than that of the in-length analysis. Therefore it was acknowledged that the proximity measure by the goal-line analysis alone may be followed by some risk. In addition, this paper was to suggest the closest distance to channel boundary from the ship's edge as one of proximity measures, instead of using the ship's deviation from the centerline of channel.

• Journal of Navigation and Port Research
• /
• v.41 no.6
• /
• pp.373-380
• /
• 2017

Operational errors caused by human factors, which is the major cause of marine accidents, include lack of knowledge, misunderstanding knowledge, and inadequate procedures. Recently, the type of propulsion mounted on KCG cutters has been diversified. In particular, the water jet propulsion unit, which was mainly installed in small boats, have been gradually expanded to medium and large size Coast Guard cutters, reaching 50% of the total. Axes types are divided into 2 to 4, and the bucket types are divided into Double Reverse Bucket(DRB) and Single Reverse Bucket(SRB); in these, the backward and steering control methods are completely different. Diversification of these operating systems can increase factors causing human error by the ships' operators. However, there is a lack of research on the maneuvering methods, considering the inherent active characteristics of each type of water jet. In this paper, we analyze the sideway method suitable for the condition of Coast Guard Exclusive wharf without assistance, based on the astern performance of each type. Then, a ship handling simulator was used for the experiment; they compared and verified through interviews of captains.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.6
• /
• pp.609-616
• /
• 2017

In this paper, we propose an algorithm to obtain more stable and high recognition rate by using left and right rotation information of input image in order to obtain a stable recognition rate in face recognition. The proposed algorithm uses the facial image as the input information in the web camera environment to reduce the size of the image and normalize the information about the brightness and color to obtain the improved recognition rate. We apply Principal Component Analysis (PCA) to the detected candidate regions to obtain feature vectors and classify faces. Also, In order to reduce the error rate range of the recognition rate, a set of data with the left and right $45^{\circ}$ rotation information is constructed considering the directionality of the input face image, and each feature vector is obtained with PCA. In order to obtain a stable recognition rate with the obtained feature vector, it is after scattered in the eigenspace and the final face is recognized by comparing euclidean distant distances to each feature. The PCA-based feature vector is low-dimensional data, but there is no problem in expressing the face, and the recognition speed can be fast because of the small amount of calculation. The method proposed in this paper can improve the safety and accuracy of recognition and recognition rate faster than other algorithms, and can be used for real-time recognition system.