• 항공우주시스템공학회지
• /
• 제13권6호
• /
• pp.1-8
• /
• 2019

아음속 유동이 흐르는 후향 계단에서, 입구 경계면에서의 난류를 모사하는 3가지 기법을 조사하였다. 입구 경계면으로 유입되는 평균 유동장과 레이놀즈 응력 프로파일은 실험에서 측정된 결과를 사용하였으며, 입구 경계면의 난류 유동 모사기법으로 synthetic eddy method(SEM), 무작위 변동(random noise) 그리고 균일한 유동 조건(uniform)을 사용하였다. 3차원 유동장의 난류 유동의 모사를 위해 대와동모사(Large Eddy Simulation, LES)를 적용하였다. 3가지 기법에 대한 입구 경계면으로 유입된 유동의 난류 특성과 유동의 재 부착(reattachment) 거리와 속도, 레이놀즈 응력(Reynolds stress)을 비교하였다.

• 한국소음진동공학회논문집
• /
• 제21권12호
• /
• pp.1138-1145
• /
• 2011

The internal broadband noise of a centrifugal fan in a household refrigerator is predicted using hybrid CAA techniques based on stochastic turbulent synthetic model. First, the unsteady flow field around the centrifugal fan is predicted using computational fluid dynamics(CFD) method. Then, the turbulent flow field is synthesized by applying the stochastic turbulent synthetic technique to the predicted flow field. The aerodynamic noise sources of the centrifugal fan are modeled on a basis of the synthesized turbulent field. Finally, the internal broadband noise of the centrifugal fan is predicted using the boundary element method(BEM) and the modeled sources. The predicted noise spectrum is compared with the experimental data. It is found that the predicted result closely follows the experimental data. The proposed method can be used as an effective tool for designing low-noise fans without expensive computational cost required generally for the LES and DNS simulations to resolve the turbulence flow field responsible for the broadband noise.

• 한국전산유체공학회지
• /
• 제20권1호
• /
• pp.77-83
• /
• 2015

Flow characteristics of synthetic jet based flow supplying devices have been computationally investigated for different device shapes. Jet momentum was produced by the volume change of a cavity by two piezoelectric-driven diaphragms. The devices have additional flow path compared with the original synthetic jet actuator, and these flow path changes the flow characteristics of synthetic jet actuator. Four non-dimensional parameters, which were functions of the shapes of the additional flow path, were considered as the most critical parameters in jet performance. Comparative studies were conducted to compare volume flow rate and jet velocity. Computed results were solved by 2-D incompressible Navier-Stokes solver with k-w SST turbulence model. Detailed computations revealed that the additional flow path diminishes suction strength of the synthetic jet actuator. In addition, the cross section area of the flow path has more influence over the jet performances than the length of the flow path. Based on the computational results, the synthetic jet based flow supplying devices could be improved by applying suitable shape of the flow path.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.627-632
• /
• 2011

The internal broadband noise of a centrifugal fan in a household refrigerator is predicted by using hybrid CAA technique based on stochastic turbulent synthetic model. First, the unsteady flow field around the centrifugal fan is predicted using Computational Fluid Dynamics (CFD) method. Then, the turbulent flow field is synthesized by applying the stochastic turbulent synthetic technique to the predicted flow field. The aerodynamic noise sources of the centrifugal fan are modeled on a basis of the synthesized turbulent field. Finally, the broadband noise of the centrifugal fan is predicted using Boundary Element Method (BEM) and the modeled sources. The predicted result is compared with the experimental data. It is found that the predicted result closely follows the experimental data. The proposed method can be used as an effective tool for designing low-noise fans without expensive computational cost required generally for the LES and DNS simulations to resolve the turbulence flow field responsible for the broadband noise.

• Wind and Structures
• /
• 제18권5호
• /
• pp.567-598
• /
• 2014

In this paper, wind induced aerodynamic loads on a standard tall building have been evaluated through large-eddy simulation (LES) technique. The flow parameters of an open terrain were recorded from the downstream of an empty boundary layer wind tunnel (BLWT) and used to prescribe the transient inlet boundary of the LES simulations. Three different numerically generated inflow boundary conditions have been investigated to assess their suitability for LES. A high frequency pressure integration (HFPI) approach has been employed to obtain the wind load. A total of 280 pressure monitoring points have been systematically distributed on the surfaces of the LES model building. Similar BLWT experiments were also done to validate the numerical results. In addition, the effects of adjacent buildings were studied. Among the three wind field generation methods (synthetic, Simirnov's, and Lund's recycling method), LES with perturbation from the synthetic random flow approach showed better agreement with the BLWT data. In general, LES predicted peak wind loads comparable with the BLWT data, with a maximum difference of 15% and an average difference of 5%, for an isolated building case and however higher estimation errors were observed for cases where adjacent buildings were placed in the vicinity of the study building.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 추계학술대회 논문집
• /
• pp.291-291
• /
• 2013

The interior vehicle noise due to the exterior aerodynamic field is an important topic in the acoustic design of a car. The air flow detached from the A-pillar and impacting the side windows are of particular interest as they are located close to the driver / passenger and provides a lower insulation index than the trimmed car body parts. HMC is interested in the numerical prediction of this aerodynamic noise generated by the car windows with the final objective of improving the products design and reducing this noise. The methodology proposed in this paper relies on two steps: the first step involves the computation of the exterior flow and turbulence induced non-linear acoustic field using the CAA(Computational aeroacoustics) solver CAA++. The second step consists in the computation of the vibro-acoustic transmission through the side window using the finite element vibro-acoustic solver Actran. The internal air cavity including trim component are included in the simulation. In order to validate the numerical process, an experimental set-up has been created based on a generic car shape. The car body includes the windshield and two side windows. The body is made of aluminum and trimmed with porous layers. First, this paper describes the method including the CAA and the vibro-acoustic models, from the boundary conditions to the different components involved, like the windows, the trims and the car cavity is detailed. In a second step, the experimental set-up is described. In the last part, the vibration of the windshield and windows, the total wind noise level results and the relative contributions of the different windows are then presented and compared to measurements. The influence of the flow yaw angle (different wind orientation) is also assessed.

• 한국소음진동공학회논문집
• /
• 제24권3호
• /
• pp.205-212
• /
• 2014

이 연구에서 현대자동차의 단순실험모델(HSM)에 대한 썬루프 버페팅에 대한 수치해석이 수행되었다. 검증을 위하여 HSM 목부위의 경계층에 대한 속도분포 해석결과를 실험결과와 비교하였다. 썬루프 해석은 두 단계로 이루어졌다. 첫 번째로 난류 RANS 모델을 이용하여 정상상태 해석이 수행되었으며, 해석결과는 CAA++의 입력값으로 사용된다. 두 번째 단계는 유동속도에 대한 1차 최대 압력피크와 버페팅 주파수 해석을 위한 비정상상태 해석이 CAA++에서 이루어졌다. 주파수와 음향압력의 수치해석 결과는 타당한 물리적 현상을 보여주고 있으며, 현대 자동차의 실험결과와 잘 일치하는 결과를 보여주었다.