• Journal of the Korean Geosynthetics Society
• /
• v.16 no.1
• /
• pp.19-29
• /
• 2017

The effects of synthetic fibers, cement content, and sand content on the flexural performance of cement-clay-sand mixtures has been evaluated through a flexural performance test with a third-point loading. Beam specimens for the flexural performance test were fabricated with a various amount of cement, sand, and synthetic fibers. Two types of fibers, PVA (Polyvinyl alcohol) and PP (Polypropylene) fibers, were employed in the test. The test results have exhibited that the factors considered in the test have significant effects on the flexural performance of the mixtures in several aspects. The flexural performance of the mixtures has been improved if the mixtures were reinforced with synthetic fibers. The flexural strength and the flexural toughness of the mixtures has been increased as the fiber content was increased. A multiple linear regression analysis has been performed to evaluate the effect of fiber content, cement dosage, and sand content on the flexural performance of the mixtures in terms of flexural strength and flexural toughness. Cement content and sand content were estimated as important factors to have an influence on the first-crack strength and the peak strength whereas the fiber content has the most significant influence on the post-crack behavior. The first-crack strength and the ultimate strength were increased as the cement content and the sand content were increased. As the fiber content was increased, the flexural toughness was increased.

• Korean Journal of Human Ecology
• /
• v.8 no.1
• /
• pp.19-24
• /
• 2005

This paper is to know the possibility of coloration of synthetic fibers with loess. Fabrics woven with polyester, nylon, and acrylic fibers were dyed by a dip-pad operation with a laboratory mangle. Drying, curing at 180$^{\circ}C$ for 10 minutes and washing were followed. Effect of curing after drying were investigated in terms of K/S values and SEM microphotographes. Reddish-yellow(a:75.13, B:15.14, ${\Delta}$E:45.31) colored fabric ascertain possibility of coloration of synthetic fibers with loess. Acrylic fiber shows highest dye uptake of the three kinds of fibers and fastness increases by curing after drying.

• Proceedings of the Korean Fiber Society Conference
• /
• 1995.10a
• /
• pp.160-161
• /
• 1995

• International Commerce and Information Review
• /
• v.10 no.1
• /
• pp.175-191
• /
• 2008

Materials Industry has a very large ripple effect on national economic development. Nevertheless, Korea has been passing over importance of this Industry. So, this study examined competitiveness on ten chief exporting items to U.S.A market based on the understanding of vital role of materials industry in the national economy. Analyzing methods were Market Share, Trade Specialization Index(TSI), and Market Comparative Advantage(MCA) and the data were collected through parts and materials statistical data which produced by Korean Commerce and Industry Minister. From this study, following results were found. i) Highly ranked items of U.S.A market share were chemical fiber drapery weaving, synthetic fiber. These items commanded over 10% share of the same market and tire, steel wire occupied 9.05%, 8.65% respectively. ii) In searching trade balance aspects through TSI, tire and steel wire secured very powerful competitiveness among examined items in trading with U.S.A. while synthetic resins and other plastic material were very weak competitiveness in the same market. iii) Analysis results of market competitiveness by MCA, indicated that chemical fiber drapery weaving, synthetic fiber and tire ensured high-powered competitiveness in U.S.A Market. Therefore, these items would be positioned as main items in the market.

• Journal of Power System Engineering
• /
• v.6 no.4
• /
• pp.30-35
• /
• 2002

This study represents the effects of the material of the air cleaner on the performance in a 4-stroke spark-ignition engine for motorcycles. This study is mainly focused on the possibility of the adopting the STS wire mesh air cleaner of a S.I engine. For investigating the possibility of that, the engine power, the fuel consumption and the exhaust gas analysis were carried out for the synthetic fiber air cleaner and the different size of 200 mesh, 250 mesh, 300 mesh of STS wire mash air cleaner. As the results of this study, the performance of STS wire air cleaner was similar to the fiber air cleaner at 9000 rpm but 300 mesh of STS air cleaner had a high engine power and torque at 9500 rpm. In the case of the synthetic fiber air cleaner the concentration of CO was low at 6500 rpm and in the case of the 300 mesh in STS wire mesh air cleaner the concentration of HC was lowest at all experimental regions.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.469-483
• /
• 2018

Steel bars have been widely used as the primary reinforcement for Precast Segmental Concrete Lining for TBM Tunnels. Previously, studies have been carried out to gauge the potential for steel fiber reinforcement to replace the use of steel bar reinforcements in the segmental lining to reduce the amount of the steel bar reinforcement. Steel fiber reinforcements have been investigated and widely applied to SFRC TBM linings to improve the constructability of SFRC TBM linings worldwide. However, the steel fiber reinforcement often caused punctures to the water membranes inside tunnel lining and had long-term durability deterioration issues caused by steel corrosion, as well as cosmetic problems. Therefore, this paper sought to gauge the potential of synthetic fiber reinforcements, which have proven to be very attractive substitutes for steel fiber reinforcements. This study analyzed the performance of both steel and synthetic fiber reinforcements in segmental linings and evaluated the applicability of the fiber reinforcements to the TBM Precast Concrete Segmental Linings of TBM tunnels. As a conclusion, this study demonstrates that the potential use of steel and synthetic fibers in various combination, can substitute the rebar reinforcement in the concrete mix for segmental concrete linings.

• Journal of the Society of Naval Architects of Korea
• /
• v.54 no.2
• /
• pp.151-160
• /
• 2017

Growing demand and rapid development of the synthetic fiber rope in mooring system have taken place since it has been used in deep water platform lately. Unlike a chain mooring, synthetic fiber rope composed of lightweight materials such as Polyester(polyethylene terephthalate), HMPE(high modulus polyethylene) and Aramid(aromatic polyamide). Non-linear stiffness and another failure mode are distinct characteristics of synthetic fiber rope when compared to mooring chain. When these ropes are exposed to environmental load for a long time, the length of rope will be increased permanently. This is called 'the creep phenomenon'. Due to the phenomenon, The initial characteristics of mooring systems would be changed because the length and stiffness of the rope have been changed as time goes on. The changed characteristics of fiber rope cause different mooring tension and vessel offset compared to the initial design condition. Commercial mooring analysis software that widely used in industries is unable to take into account this phenomenon automatically. Even though the American Petroleum Institute (API) or other classification rules present some standard or criteria with respect to length and stiffness of a mooring line, simulation guide considers the mechanical properties that is not mentioned in such rules. In this paper, the effect of creep phenomenon in the fiber rope mooring system under specific environment condition is investigated. Desiged mooring system for a Mobile Offshore Drilling Unit(MODU) with HMPE rope which has the highest creep is analyzed in a time domain in order to investigate the effects creep phenomenon to vessel offset and mooring tension. We have developed a new procedure to an analysis of mooring system reflecting the creep phenomenon and it is validated through a time domain simulation using non-linear mooring analysis software, OrcaFlex. The result shows that the creep phenomenon should be considered in analysis procedure because it affects the length and stiffness of synthetic fiber rope in case of high water temperature and permanent mooring system.

• Journal of Environmental Health Sciences
• /
• v.27 no.3
• /
• pp.107-112
• /
• 2001

This work reports the application of a hollow fiber module(HFM) for Cr(VI) extraction from heavy metal salts mixed solution by using microporous hydrophobic hollow fiber module. In HFM configuration, the organic extraction used for the extraction of Cr(VI) was di-(2-ethyl hexyl) phosphoric acid(D2EHPA) diluted with n-heptane. The study of HFM includes the influence of hydrodynamic and chemical condition, i.e., the flow rate of feed solution, the time of reactive extraction, the concentration of feed solution, and the pH of aqueous phase solutions. Several experiments with synthetic solution of different mixed components system of Cr(VI) solutions established optimum condition to achieve a clean separation of Cr(VI). It was possible to separate Cr(VI) in the presence of metal salts mixed solution, such as Zn(II), Ni(II), Cu(II), and Cd(II) using the HFM technique.

• Polymer Science and Technology
• /
• v.7 no.1
• /
• pp.59-67
• /
• 1996

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.234-242
• /
• 2002

A shape optimal design of synthetic intervertebral disc prosthesis is performed using a three-dimensional finite element method. Geometric parameters are introduced to model the cross-sectional geometry of the intervertebral disc. It is assumed that the total strain energy in the intact intervertebral disc is minimized under the normal load conditions, as often cited in other references. To calculate the stain energy density, both the nonlinear material properties and the large deformations are taken into account. The design variables of the annulus fiber angle and the area ratio of the nucleus pulposus are calculated as 31°and 30%, respectively, which complies well with the intact disc. Thus, the same optimization procedure is applied to the design of the synthetic intervertebral disc prosthesis whose material properties are different from the intact disc. For the given synthetic material properties, the values of 67°and 24% for the fiber angle and the area ratio are obtained.