• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.2
• /
• pp.141-145
• /
• 2009

A C-to-SystemC synthesizer which processes the input behavior according to high-level synthesis, and then transforms the synthesis result into SystemC module code is implemented in this paper. In the synthesis process, the input behavioral description in C source code is scheduled using list scheduling algorithm and register allocation is performed using left-edge algorithm on the result of scheduling. In the SystemC process, the output from high-level synthesis process is transformed into SystemC module code by combining it with SystemC features such as channels and ports. The operation of the implemented C-to-SystemC synthesizer is validated through simulating the synthesis of elliptic wave filter in SystemC code. C-to-SystemC synthesizer can be used as a part of tool-chain which helps to implement SystemC design methodology covering from modeling to synthesis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.852-856
• /
• 2014

$BaTiO_3$ nano powder can be synthesized by hydrate salt method at $120^{\circ}C$ in air. Decreasing the thickness of thick film, the nano dielectric particle is needed in electronic ceramics. However, the synthesis of $BaTiO_3$ nano particle at low temperature in air and their mechanism were not reported enough. And ultrasonic treatment can be tried because of low temperature process in air. Therefore, in this study, the $BaTiO_3$ nano powder was synthesised with the synthesis time and ultrasonic treatment at $120^{\circ}C$ in air. In the synthesis process, the effects of process were evaluated. From the experimental observation, the synthesis mechanism was proposed. The homogeneous $BaTiO_3$ particle was synthesised by KOH salt solution at $120^{\circ}C$ for 1hour. It was conformed that the ultrasonic treatment effected on the increase of synthesis rate. After cutting the salt powder using FIB, $BaTiO_3$ nano particles observed homogeneously in the cross-section of the salt particle.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.774-777
• /
• 2002

A systematic synthesis process is described for the simulation of current-controllable inductors using operational transconductance amplifiers (OTAs). The process is used to obtain three circuits; two are believed to be novel. The process is also applied to design current-controllable frequency-dependent negative resistances (FDNRs). Operation principles of designed circuits are presented and experimental results are used to verify theoretical predictions. The results show close agreement between predicted behavior and experimental performance.

• IE interfaces
• /
• v.24 no.2
• /
• pp.156-163
• /
• 2011

The radiopharmaceutical synthesis for PET (positron emission tomography) is composed of chemical reactions using automated synthetical equipment. Due to the radioactive material, the automated equipment is being frequently developed to replace human operators who conduct dangerous, repetitive and dexterous operations. As to operation, the manipulating program is commonly coded using the spread sheet while the whole actuators are mapped in every step. The process map (program) is changed according to such parameters as temperature of reactor, keeping time, mixture sequence and amount of reagent. In cases of customizing the automated synthetical equipment or developing the new radiopharmaceuticals, lots of experiments should be conducted and the programming mistake is not allowed as it can lead abnormal control of the equipment to leak the radioactive materials. The exact process map has depended on trial and error manner. Thus, this study developed the methodology to tabulate the synthetical process to convert the process map automatically while the synthetical module formation is represented by a network model. The proposed method is validated using the actual radiopharmaceutical synthetical procedure.

• Textile Coloration and Finishing
• /
• v.27 no.4
• /
• pp.245-260
• /
• 2015

The effect of salt milling process on the crystal size, morphology, and color characteristics of C.I. Pigment Red 57:1 was studied. The primitive morphology and color properties of the pigment after synthesis were studied in the former series work. The size and morphology of primary particles and the second aggregation features should be considered because they are very important to determine pigment quality. We compared the primary morphology of pigment particles before drying with the secondary aggregated morphology of pigment particles after drying and salt milling process. Morphological properties were investigated by particle size analysis, X-ray diffraction, and scanning electron microscopy and color measurement was carried out. Significant reduction in particle size as well as enhanced crystallite size after salt milling process was observed. This result might give a difference in color of the pigment, turning into brighter and more blue-toned red color. It was revealed that synthesis condition affect the morphology and color of the pigment even after milling. Increase in HCl concentration in the synthesis process enhanced crystal size and quality forming bluer-red pigments but an increase in $CaCl_2$ concentration resulted in more amorphous crystals forming darker-red pigments after salt milling.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.151-163
• /
• 2000

A polymerized organic-inorganic complexation route is introduced for the synthesis of oxide ceramic powders. Polyvinyl alcohol was used as the organic carrier for precursor ceramic gel. Porous and soft powders, which have a high specific surface area, were obtained after calcinating the aerated precursors. The PVA content and its degree of polymerization had a significant influence on the homogeneity of the final powder. In particular, attrition milling process with the porous powder resulted in ultra-fine particles. In the case of the preparation of cordierite powder, nano-size powder, which has a high specific surface area of 181 ㎡/g, was obtained by the milling process. The complexation route was also applied to the synthesis of unstable phase in room temperature like beta-cristobalite, high temperature form of silica.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.554-557
• /
• 2001

In this work, we had synthesis the GaN powder by direct reaction between Ga and NH$_3$at the temperature range of 1000∼1150$^{\circ}C$, and investigated the reaction condition dependence of the GaN yield and some properties of GaN powder. The synthesized powder had Platelet and prismatic shape and showed hexagonal crystalline structure with the lattice constants of a= 3.1895 ${\AA}$, c= 5.18394 ${\AA}$, and the ratio of c/a = 1.6253. The GaN powder synthesis processes were examined based on the oxidation process of mater, and found as combined with mass transport process for the initial stage and diffusion-limited reaction for the extended reaction.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.831-832
• /
• 2006

Solid-state processing via the bulk mechanical alloying enables us to directly fabricate $Mg_2X$ semi-conductive material performs. Precise control of chemical composition leads to investigation on the dilution and enrichment of X in $Mg_2X$. Two types of solid-state reactivity are introduced: e.g. synthesis of $Mg_2Si$ from elemental mixture Mg-Si is nucleation-controlled process while synthesis of $Mg_2Sn$ from Mg-Sn, diffusion-controlled process. Thermoelectricity of these $Mg_2X$ is evaluated for discussion on the validity and effectiveness of this new PM route as a reliable tool for fabrication of thermoelectric compounds.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.3
• /
• pp.75-80
• /
• 2012

Gasification is a therm-chemical conversion process to convert various solid fuels into gaseous fuels under limited supply of oxygen in high temperature environment. Considering current availability of biomass resources in this country, the gasification is more attractive than any other technologies in that the process can accept various combustible solid fuels including plastic wastes. Mixed fuels of biomass and polyethylene pellets were used in gasification experiments in this study in order to assess their potential for synthesis gas production. The results showed that higher reaction temperatures were observed in mixed fuel compared to woodchip experiments. In addition, carbon monoxide, hydrogen, and methane concentrations were increased in the synthesis gas. Heating values of the synthesis gas were also higher than those from woodchip gasification. There are hundred thousand tons of agricultural plastic wastes generated in Korea every year. Co-gasification of biomass and agricultural plastic waste would provide affordable gaseous fuels in rural society.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.201-206
• /
• 2000

In this work transfer function synthesis method based on FRF data of each substructure is investigated for a complex structure composed of many substructures. Though the transfer function synthesis method has superiority to analyze the characteristics of interfaces among substructures effectively, many problems arise in the computation process, especially matrix inversion process. Due to computational problems, the error between the data obtained by test and the predictions through computations is inevitable. So in this paper, computational aspects in the transfer function synthesis method are examined through a steering system problem of passenger car. For the FBS method, frequency response functions of 3 substructures are measured experimentally. Effects of several parameters such as matrix inversion method, connection conditions between substructures and off-diagonal terms on system response are studied numerically.