• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.271-275
• /
• 2014

A New Single Phase Active Power Filter Controller is proposed using Rotating Synchronous Frame d-q transformation. Instantaneous Active Power is calculated using d-q transformation. Average Value of Instantaneous Active Power is obtained using Low Pass Filter. Because power factor is corrected, source current is in phase with source voltage. Amplitude of source current is calculated using single phase power formula. Reference signal of compensated current of Active power filter is obtained from source current reference signal minus load current. Simulation is performed using hysteresis current controller in proposed new controller. Simulation result shows that because active power filter compensates load current, source current is in phase with source voltage and source current is sinusoidal. And Hilbert transformer is builded using all pass filter.

• Journal of Power Electronics
• /
• v.3 no.1
• /
• pp.49-54
• /
• 2003

A novel control scheme of using a single electronic drive to synchronize two synchronous motors is investigated analytically. The developed control strategy extends the conventional vector control technology, Specifically, it utilizes the property that the motion of two motors can be independently controlled by the q-axis currents provided the desired q-axis currents can be achieved by adjusting physical armature currents. The latter part is indeed guaranteed by adding a position offset to one of the motors. This work has a potential of cost saving in practice where the cost of drive is a major concern.

• Journal of Power Electronics
• /
• v.11 no.3
• /
• pp.375-380
• /
• 2011

A STATic synchronous COMpensator (STATCOM) is a shunt connected voltage source converter (VSC) based FACTS controller using Gate Turn Off (GTO) power semiconductor devices employed for reactive power control. The operation principal is similar to that of a synchronous condenser. A typical application of a STATCOM is voltage regulation at the midpoint of a long transmission line for the enhancement of power transfer capability and/or reactive power control at the load centre. This paper presents the modeling of STATCOM with twenty four pulse three level VSC and Type-1 controller to regulate the reactive current or the bus voltage. The performance is evaluated by transient simulation. It is observed that, the STATCOM shows excellent transient response to step change in the reactive current reference. While the eigenvalue analysis is based on D-Q model, the transient simulation is based on both D-Q and 3 phase models of STATCOM (which considers switching action of VSC).

• Journal of Power Electronics
• /
• v.3 no.1
• /
• pp.33-39
• /
• 2003

This paper presents the self-commissioning for surface-mounted permanent magnet synchronous motor. The proposed strategy executes three tests with a vector controlled inverter drive system. To do this, synchronous d-q axes currents are appropriately controlled for each test. From the three tests, armature resistance, armature inductance, equivalent iron loss resistance, and emf coefficient are identified automatically. The validity of the proposed strategy is confirmed by experimental results.

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.51-56
• /
• 2001

This paper is proposed an efficiency optimization control algorithm for a synchronous reluctance motor (SynRM) which minimizes the copper and iron losses. fen exists a variety of combinations of d and q-axis current which provide a specific motor torque. The objective of the efficiency optimization controller is to seek a combination of d and q-axis current components, which provides minimum losses at a certain operating point in steady state. It is shown that the current components which directly govern the torque production have been very well regulated by the efficiency optimization control scheme. The proposed algorithm allows the electromagnetic losses in variable speed and torque drives to be reduced while keeping good torque control dynamics. Simulation results are presented to show the validity of the proposed algorithm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.9
• /
• pp.89-95
• /
• 2015

This paper presents a current sensorless maximum torque control of a synchronous reluctance motor drive. Stator current and current angle vs. maximum torque are obtained using measured d-axis and q-axis inductances. Then, d and q-axis stator voltage references for current sensorless maximum torque control are calculated from stator voltage equations. The proposed method is verified by simulation results comparing with conventional method.

• Journal of Magnetics
• /
• v.19 no.4
• /
• pp.411-417
• /
• 2014

This paper presents the shape optimization of a permanent magnet synchronous motor to reduce the torque ripple and iron loss. Specifically, the harmonics of the electromotive force and cogging torque are decreased by adjusting the permanent magnet arrangement and non-uniform air gap length. In addition, an additional flux path along the q-axis is proposed with a unique rotor shape to increase the q-axis inductance and reluctance torque. The improvement in the performance of the proposed model is verified with simulated and experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.3
• /
• pp.211-220
• /
• 2003

This paper presents an implementation of direct torque control (DTC) of Reluctance Synchronous Motor (RSM) with an efficiency optimization. The equipment circuit in Reluctance Synchronous Motor which consider with iron losses is theoretically analyzed and the optimal current ration between torque current and exiting current analytically derived to drive RSM at maximum efficiency. For RSM, torque dynamics can be maintained even with controlling the flux level because a torque is directly proportional to the stator current unlike induction motor. The experimental results are presented to validate the applicability of the proposed method. The developed control system show high efficiency features with 1.0 Kw RSM having 2.57 ratio of d/q reluctance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.3
• /
• pp.349-357
• /
• 2014

The performance of a Synchronous Reluctance Motor (SynRM) in terms of torque and power factor depends on the two-axis inductances $L_d$ and $L_q$ of the machine. The Axially Laminated Anisotropic (ALA) rotor should be proposed in an effort to increase the $L_d/L_q$ ratio and the $L_d-L_q$ difference to secure high torque density and high power factor. So, ALA rotor is suitable for high speed instruments. This paper deals with optimum design of Axially Laminated Anisotropic Synchronous Reluctance Motor (ALA-SynRM) and comparison of characteristics with induction motor. Coupled Finite Element Methodology (FEM) & Response Surface Methodology (RSM) have been used to evaluate optimum design solutions. Comparisons are given with characteristics of a same rated wattage induction motor and those of ALA-SynRM respectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.12
• /
• pp.83-87
• /
• 2015

This paper presents a simple notch filter, which is so suitable for three-phase unbalanced and distorted power line. In the d-q synchronous transformation, three-phase unbalanced and distorted voltages generate lots of ripple voltages on d-q axes. The ripples make disturbances on controllers such as PLL of phase tracking. Unbalanced state makes ripple of double the frequency of power line. Odd harmonics 5th and 7th on the line make even 4th and 6th ripples on d-q axes due to the rotating reference frame, respectively. Cascaded two comb filters, delay lines 1/4T and 1/8T, are adopted for the ripple rejection. The filter rejects harmonics 2nd, 4th, 6th, 10th and so on. They are very effective to remove the ripples of both unbalance and distortion. The filter, implemented by two FIFOs on an experimental system, is adopted on a PLL controller of power line phase tracking. Through the simulation and experimental results, performance of the proposed comb filter has been validated.