• 산업기술연구
• /
• 제32권A호
• /
• pp.103-107
• /
• 2012

Due to improvement of the semiconductor technology, the LED replaces the conventional lighting source and LED drivers have been studied and developed. The LED is driven by the constant current control method according to its characteristics. For the constant current control method, the linear regulator and the switching regulator is used. The switching regulator is usually used to LED drivers because it has specific characteristics as the wide input dynamic range and the high efficiency. In this paper, we have described the principle and the implement of the switching regulator, using the drive IC and the low cost DSP chip. Also, both methods have been implemented and its electrical characteristics had almost same experimental results in the steady state and the transient state.

• 한국전기전자재료학회논문지
• /
• 제24권9호
• /
• pp.710-712
• /
• 2011

In this study, we fabricate resistive switching random access memory (ReRAM) devices constructed with a Al/$HfO_2$/ITO structure on glass substrates and investigate their memory characteristics. The hafnium oxide thin film used as a resistive switching layer is sputtered at room temperature in a sputtering system with a cooling unit. The Al/$HfO_2$/ITO device exhibits bipolar resistive switching characteristics, and the ratio of the high resistance (HRS) to low resistance states (LRS) is more than 60. In addition, the resistance ratio maintains even after $10^4$ seconds.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.301-302
• /
• 2014

This paper describes four switch three-phase Z-source rectifier with improved switching characteristics. This configuration has some advantages switching loss and optimal drive circuit. The rectifier has buck-boost function by shoot-through state. Also, the rectifier has the advantage of decreasing inrush current in start-up and transient states. In order to reduce harmonics PWM modulation technique with a variable index has been suggested. Four switch three-phase Z-source rectifier with improved switching characteristics can output stable DC voltage at the same time decreasing the system's harmonic current. And also the paper presents an application of DCC method in Z-source rectifier. Principles and dynamics of the system are discussed in detail. After having viewed the results we can confirm that the proposed method is eligible and efficient.

• 조명전기설비학회논문지
• /
• 제23권9호
• /
• pp.98-107
• /
• 2009

기존의 하드 스위칭 고주파 PWM DC-DC 컨버터는 펄스 변조 캐리어 주파수의 고주파화를 수반하고, 전력용 반도체 스위칭 소자의 스위칭 손실의 증대나 스위칭 과도현상이 수반된 전압 서지나 전류 서지에 의한 EMI 등의 문제점들이 있다. 이러한 문제를 효과적으로 해결하기 위해 본 논문에서는 새로운 소용량 승압형 PWM 쵸퍼 회로의 동작원리를 서술하고, 시뮬레이션과 실험을 통하여 특성을 도출하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.116-123
• /
• 1997

This paper was described about principle and form of proposed circuit made use of soft switching technology ZVS(Zero Voltages Switching) and ZCS(Zero Current Switching) to reduce turn on and off loss at switching. Also, the analysis of the proposed circuit is described generally by using normalized parameter and basic operating principle and driving characteristics have been evaluated as to switching frequency and load p arameter. Based on the characteristics value, a method of circuit design is proposed. In addition, Pspice's simulation and experimental waveforms are compared with theoretical ones. The experimental results shows that the proposed Inverter can be used practically such as power source system for induction cooker etc.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권2호
• /
• pp.75-82
• /
• 1994

The existence of peroodic impulse noises in distribution line carrier (DLC) communication system is known to be the most serious obstacle for improving DLC communication quality in reliability and capacity. From the spectral points, impulse noises can be divided into baseband type and modulation type the noise width of whichs are much different each other. With each nose type, this study presents the basic characteristics in relation to what they originate from and how their spectrum properties are revealed. The baseband type impulse noise is normally caused from thyristor circuit running with low switching speed and the modulation type noise from the circuit of switching power supply. The base wave of modulation noise is shown to be the pulsuatic charging current to primary condenser in switching power circuit. The study result indicates also that placing the DLC carrier frequency away the band predominated by modulated noise especially from RCC type switching power circuit is very important in DLC design.

• 한국전기전자재료학회논문지
• /
• 제17권5호
• /
• pp.530-535
• /
• 2004

We have studied 90$^{\circ}$ twisted nematic mode switching by fringe electric field(F-TN mode) using a liquid crystal (LC) with negative dielectric anisotropy. In the device, two polarizers are parallel each other, electrodes exist only on bottom substrate, and one of rubbing direction is coincident with polarizer axis. Therefore, the cell shows a black state before a voltage is applied. With a bias voltage generating fringe-electric field, the LC twists perpendicular to fringe electric field such that the LCs are almost homogeneously aligned except near the bottom surface since the negative type of the LC is used. Consequently, the new device exhibits much wider viewing angle than that of the conventional TN mode due to in-plane switching and relatively high transmittance since the LC director above whole electrode area aligns parallel to the polarizer axis.

• Applied Science and Convergence Technology
• /
• 제24권6호
• /
• pp.278-283
• /
• 2015

In this work, the electrical bistability of an organic CT complex is demonstrated and the possible switching mechanism is proposed. 2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) and tetracyanoquinodimethane (TCNQ) are used as an organic donor and acceptor, respectively, and poly-methamethylacrylate (PMMA) is used as a polymeric matrix for spin-coating. A device with the Al/($Al_2O_3$)/PMMA:BCP:TCNQ[1:1:0.5 wt%]/Al configuration demonstrated bistable and switching characteristics similar to Ovshinsky switching with a low threshold voltage and a high ON/OFF ratio. An analysis of the current-voltage curves of the device suggested that electrical switching took place due to the charge transfer mechanism.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1383-1386
• /
• 2005

Non-isolated OSAKA Converter, which removes a three-phase transformer, is described in this paper. The converter switches once in every half cycle of an AC commercial power source. Therefore, it can solve many problems caused by the high frequency operation. The proposed converter achieves the soft-switching operation and the EMI noise can be reduced. In this circuit, the resonant capacitor, which is used for the soft-switching operation, is utilized for the improvement of an input current waveform. To achieve low cost and compact structure, non-isolated OSAKA converter removes a three-phase transformer of the OSAKA converter. By removing the three-phase transformer, three phase currents occur the interferences each other. To avoid the interference, a new switching method for non-isolated OSAKA converter is preposed. The converter can be constructed by the low-speed large power devices. The converter generates the low distorted input current waveforms with high power factor.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.35-39
• /
• 1995

After making the light modulator using the BLN-PZT 9.0/65/35 specimen which has the slim-loop hysteresis characteristics and quadratic electro-optic characteristics, switching and spectral response characteristics were investigated. As the results of switching characteristics of the light modulator, it was found that the transmitted light intensity was modulated by both AC and pulse voltage. From the possibility of the selective transmission of the RGB(Red, Green, Blue) spectrum with electric field, the application for the light modulator, light shutter and color filter was expected.