• 산업경영시스템학회지
• /
• 제20권41호
• /
• pp.103-112
• /
• 1997

In this paper, a nonhierarchial integrated information network with circuit switched and packet switched traffic is considered. It is assumed that circuit switched traffic is allowed to attempt an alternate path if the direct path is blocked, whereas packet switched traffic is not. The network uses a movable boundary scheme to allocate bandwidth dynamically. To analyze the performance of this type of network, EEBP(End to End Blocking Probability) is selected as a measure for circuit switched traffic and average time delay for packet switched traffic, respectively. EEBP and average time delay are derived analytically. Using the two proposed measure, the performance of the network under various bandwidth allocations and arrival patterns are observed. Moreover, the arrival rate of one link for circuit switched traffic is obtained from an approximation formula. Simulation results reveal the validity of the proposed approximation method.

• 전자공학회논문지A
• /
• 제32A권8호
• /
• pp.1-10
• /
• 1995

We have analyzed the reliability of failure models in circuit-switched networks. These models are grid topology circuit-switched networks, and each node transmits a packet to a destination node using a Flooding routing method. We have assumed that the failure of each link and node is independent. We have considered two method to analyze reliability in these models : The Karnaugh Map method and joint probability method. In this two method, we have analyzed the reliability in a small grid topology circuit switched network by a joint probability method, and comared analytic results with simulated ones. For a large grid enormous. So, we have evaluated the reliability of the network by computer simulation techniques. As results, we have found that the analytic results are very close to simulated ones in a small grid topology circuit switched network. And, we have found that network reliability decreases exponentially, according to increment of link or node failure, and network reliability is almost linearly decreased according to increment of the number of links, by which call has passed. Finally, we have found an interesting result that nodes in a center of the network are superior to the other nodes from the reliability point of view.

• 제어로봇시스템학회논문지
• /
• 제9권1호
• /
• pp.90-98
• /
• 2003

The real-time industrial network, often referred to as fieldbus, is an important element for building automated manufacturing systems. Thus, in order to satisfy the real-time requirements of field devices, numerous fieldbus protocols have been announced. But the application of fieldbus has been limited due to the high cost of hardware and the difficulty in interfacing with multi-vendor products. Therefore, as an alternative to fieldbus, the computer network technology, especially Ethernet (IEEE 802.3), is being adapted to the industrial environment. However, the crucial technical obstacle for Ethernet is its non-deterministic behavior that makes it inadequate for industrial applications where real-time data have to be delivered within a certain time limit. Recently, the development of switched Ethernet shows a very promising prospect for industrial application due to the elimination of uncertainties in the network operation resulting in much improved performance. This paper focuses on the application of the switched Ethernet for industrial communications. More specifically, this paper presents an analytical and experimental performance evaluation of the switched Ethernet and a case study about networked control system.

• 제어로봇시스템학회논문지
• /
• 제16권4호
• /
• pp.403-410
• /
• 2010

The switched Ethernet has many features for real-time communications such as providing traffic isolation, large bandwidth, and full-duplex links, and so on. The switched Ethernet, however, cannot guarantee the timely delivery of a real-time message because message delay increases when collisions occurs at the output ports and message loss can even occur due to the overflow at the output buffer. Recently, many research efforts have been done to use the switched Ethernet as an industrial control network. In the industrial control network, sensors periodically sense the physical environment and transmit the sensed data to an actuator, and the periodic messages from sensors to actuators have typically real-time requirements such that those messages must be transmitted within their deadlines. This paper first suggests a feasible condition for EDF (Earliest Deadline First)-based scheduling of periodic messages on a synchronized switched Ethernet and a message scheduling algorithm which satisfies the proposed feasible condition. Pedreiras, et al. [10] suggested a feasible condition for message scheduling on the Ethernet (shared media Ethernet), but there has been no research result on the scheduling condition on the switched Ethernet until now. We compared the real-time message scheduling capacity between the Ethernet and the switched Ethernet by simulation. The simulation result shows that the message scheduling capacity of the Ethernet has almost remained constant as the number of nodes on the network increases, but, in the case of the switched Ethernet, the message scheduling capacity has increased linearly according to the number of nodes on the network.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 Proceedings ICPE 98 1998 International Conference on Power Electronics
• /
• pp.197-200
• /
• 1998

Three switched-capacitor(SC) networks are presented including series-parallel capacitor set, reversed-switched-capacitor network and push-pull switched-capacitor network, the performances of which are discussed. Combining the SC networks with traditional DC-DC converters, we form several new topologies. Experiment and analyzed results show that the behavior of a DC-DC converter with large voltage ratio can be improved. A wider voltage conversion range is also obtained.

• 제어로봇시스템학회논문지
• /
• 제10권8호
• /
• pp.718-725
• /
• 2004

The real-time industrial network, often referred to as fieldbus, is an important element for intelligent manufacturing systems. Thus, in order to satisfy the real-time requirements of field devices, numerous fieldbus protocols have been announced. But, the application of fieldbus has been limited due to the high cost of hardware and the difficulty in interfacing with multi-vendor products. Therefore, as an alternative to fieldbus, the computer network technology, especially Ethernet (IEEE 802.3), is being adapted to the industrial environment. However, the crucial technical obstacle for Ethernet is its non-deterministic behavior that makes it inadequate for industrial applications where real-time data have to be delivered within a certain time limit. Recently, the development of switched Ethernet shows a very promising prospect for industrial application due to the elimination of uncertainties in the network operation resulting in much improved performance. This paper focuses on the application of the switched Ethernet with cascade structure for industrial communications. More specifically, this paper presents an analytical performance evaluation of switched Ethernet with cascade structure, and a case study about networked control system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.491-494
• /
• 2002

The real-time industrial network often referred to as fieldbus, is an important element for building automated manufacturing systems. Thus, in order to satisfy the real-time requirements of field devices such as sensors, actuators, and controllers. numerous standard organizations and vendors have developed various fieldbus protocols such as Profibus, WorldFIP and Foundation Fieldbus. However, the application of fieldbus has been limited due to the high cost of hardware and the difficulty in interfacing with multi-vendor products. In order to solve these problems, the computer network technology, especially Ethernet (IEEE 802.3), is being adopted lo the industrial environment. The crucial technical obstacle for Ethernet is that its non-deterministic behavior makes it inadequate for industrial applications where real-time data such as control command and alarm signal hale to be delivered within a certain time limit. Recently, the development of switched Ethernet shows a very promising prospect for industrial application due to the elimination of uncertainties in the network operation resulting in much improved performance. This paper focuses on the application of the switched Ethernet for industrial comm unications.

• 제어로봇시스템학회논문지
• /
• 제12권12호
• /
• pp.1241-1248
• /
• 2006

In high reliability systems for industrial network such as railway signal system, fieldbus protocols have been known to satisfy the real-time and fault tolerant requirements. But, the application of fieldbus has been limited due to the high cost of hardware and software, and the difficulty in interfacing with multi-vendor products. Therefore, as an alternative to fieldbus, the computer network technology, especially Ethernet(IEEE 802.3), is being adapted to the industrial network. In this paper, we propose a switched Ethernet based railway signal system because of its very promising prospect for industrial application due to the elimination of uncertainties in the network operation. In addition, we propose the redundancy architecture for the reliability of network components. More specifically, this paper presents an analytical performance evaluation of switched Ethernet for railway signal system, and shows experimental evaluation of redundancy architecture.

• 한국통신학회논문지
• /
• 제21권2호
• /
• pp.447-460
• /
• 1996

Network optimization and design procedures often separate quality of service (QOS) performance measures from reliability issues. This paper considers channel allocation and flow assignment (routing) in a network subject to link failures. Fault-tolerant channel allocation and flow assingments are determined which minimize network cost while maintaining QOS performance requirements. this approach is shown to yield significant network cost reductions compared to previous heuristic methods used in the design of packet switched network with unreliable links.

• 산업경영시스템학회지
• /
• 제16권28호
• /
• pp.181-186
• /
• 1993

The objective of this paper is to present a method for synthetic performance and quality evaluation of dial up network modem in users place. In the past, universally recognized criteria have not been available to model switched network modem performance. Reasonable assurance of modem performance on the public switched telephone network by standardized test channel which is suggested by ELA(Electronic Industries Association). These tests of modem from a variety manufacturers more reflective of actual performance on the network.