• Journal of the Korean Society of Combustion
• /
• v.21 no.2
• /
• pp.15-21
• /
• 2016

Flame characteristics and combustion stability of a swirl coaxial injector are studied experimentally. Characteristics of flame and combustion instability are analyzed with the parameter of MFR (momentum flux ratio) using hexane instead of kerosene. Flame patterns of blue and yellow are changed with variable MFR. Combustion instabilities are measured and analyzed by adopting a model chamber. Combustion instability mapping is made by evaluating damping factor at the 2 L (second longitudinal) mode with variable MFR in 63 cases for operating condition.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.7
• /
• pp.619-625
• /
• 2015

Swirl injectors are widely used for Liquid Rocket Engine(LRE) as fuel injection system and following researches are also being carried out throughout the world. Especially, solving combustion instability problem is essential for every type of LREs. In this study, cold test was carried out for open type swirl injector as a fundamental research to solve combustion instability problem. Pressure fluctuation was applied to the inlet flow coming into the injector and the following response characteristics were observed. The effect of swirl chamber geometry was also studied by changing both swirl chamber length and diameter.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.6
• /
• pp.485-496
• /
• 2015

The present study presents experimental results on the characteristics of emission spectra of kerosene/air swirl flames. The aviation fuel Jet A-1, which is used for the liquid rocket engines of the Korea Space Launch Vehicle, is used with three different swirlers to investigate the swirl strength effects. The emission spectra from the flames are measured with a spectrometer as the swirl strength and combustion air temperature are varied. Chemiluminescence intensities of $OH^*$, $CH^*$ and $C_2{^*}$ are identified from the spectra. The chemiluminescence intensities from the kerosene flames show sensitivity to the swirl strength and are affected by changes in the combustion air temperature. Among the three radicals of interest, $C_2{^*}$ show the most significant changes in chemiluminescence intensity with the swirl strength and equivalence ratio. The intensity ratios $I_{OH^*}/I_{CH^*}$ and $I_{C_2{^*}}/I_{CH^*}$ are adequate for indicating changes in the equivalence ratio with the air and fuel mass flow rates, respectively.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.852-857
• /
• 2001

This paper discusses the combustion characteristics of water emulsified fuel produced by swirl impinging mixer. The experiments are given in a test boiler and a commercial boiler. Flame temperatures, flame shapes and exhaust emissions are measured in the test boiler, and thermal efficiency is tested in the commercial boiler. The test data show the water in oil makes the flame wider and shorter, the flame temperature lower and the NOx and smoke lower. Also, the commercial boiler test shows the thermal efficiency increases as well as the emissions decrease.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.5
• /
• pp.37-44
• /
• 1998

Lean burn combustion is an important concept for improving the fuel consumption and exhaust emissions. However, the lean burning is associated with increased cycle-to-cycle combustion variations due to the ignition instabilities and redu- ced flame propagation rates. Engine stability under lean mixture conditions could be improved by increasing flame speed through enhanced flow characteristics and by securing ignitability with improvement of ignition systems. The effects of flow motion and ignition characteristics on the combustion performances were investigated in a 4-valve SI engine. Flow motions of tumble-swirl were varied with a swirl control valve attached at the inlet ports, while ignition energy and its distribution were controlled in a high -frequency ignition system by changing spark duration and spark frequency. The improvement of lean burn performance by the optimum flow motion and ignition characteristics is discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.37-43
• /
• 2003

The objective of this work is to investigate the effect of swirl, injection pressure and pilot injection on D.I. diesel combustion by using a transparent engine system. The test engine is equipped with common rail injection system to obtain high pressure and to control injection timing and duration. In this study, the combustion analysis and steady flow test were conducted to estimate the heat release rate from in-cylinder pressure. Soot distribution in diffusion flame according to swirl ratio, injection pressure and pilot injection was investigated by using LII technique. As the results, high injection pressure was found to shorten ignition delay as well as enhance peak pressure and heat release rate was greatly affected by injection timing and pilot injection. In addition, the results showed that the period of soot formation corresponded to the diffusion flame.

• 한국연소학회:학술대회논문집
• /
• 2000.05a
• /
• pp.162-168
• /
• 2000

This paper conducted experimental study of turbulent diffusion flame, equipped with a unique double swirler combustor for gas fuel. The burner has two vane swirlers which are fitted to primary, secondary air channel. Temperature, and NOx emission concentrations are measured in combustion flame region and velocity in cold flow for various primary/secondary air ratio conditions. The results showed the characteristics of swirl flame and decreasing NOx concentrations with increasing primary/secondary air ratio.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.686-691
• /
• 2000

The flat flame made by swirling air has lots of the different characteristics according to the swirl numbers in the burner throat. Its combustion characteristics are also affected by them. In this study, the flow patterns in the flat flame burner which is no firing condition were investigated experimentally with using smoke in terms of each swirl number. Also the blow off, flame structure, temperature distribution and NO emission in the firing condition were measured at the atmosphere and combustion furnace.

• 한국연소학회:학술대회논문집
• /
• 2002.11a
• /
• pp.149-155
• /
• 2002

A promising new approach to achieve low pollutants emission and improvement of flame stabilities is tested experimentally using a hybrid cyclone jet combustor employing both premixed and diffusion combustion mode, Three kind of nozzles are used for LNG(Liquified Natural Gas) as a fuel. The combustor is operated by two method, One is ATI(Air Tangential Injection) mode, generated swirl flow by air as general swirl combustor, and the other is PTI(Premixed gas Tangential Injection) mode, The PTI mode consists of diffusion flame of axial direction and premixed cyclone flame of tangential direction in order to stabilized the diffusion flame. The results showed that the stable region of the PTI mode is more larger than the ATI mode. In addition, the reduction of NOx emission in PTI mode, as compared with that for the ATI mode is at least 50% in stable region. Also, even using the low calorific fuel as $CO_2$-blended gas, the cyclone jet combustor has high performance of flame stability.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.8
• /
• pp.79-86
• /
• 2006

Swirl injector with adjustable backhole length was analyzed to suppress high-frequency combustion instability in Liquid Rocket Engines. In order to analyze the effect of variable backhole injector as an acoustic absorber, backhole injector was regarded as a quarter-wave resonator. As a result of theoretical approaches and acoustic tests, backhole injector with adjustable length could decrease the unstable modes of combustion chamber. And the damping efficiency was estimated by measuring damping rates experimentally.