• Journal of Sensor Science and Technology
• /
• v.29 no.6
• /
• pp.412-419
• /
• 2020

In this study, a PID control method for sweeping automatic linearization of a wavelength swept laser is proposed. First, the closedloop transfer function embodying the PID control is derived. Through the simulation of the function, K_p = 0.022, K_i = 0.008, K_d = 0.002 were obtained as the best PID coefficients for fast linear sweeping. The performance test using the PID coefficients showed that linear sweeping was held up well with a 98.7% decrement in nonlinearity after the 10th feedback, and 45 nm sweeping range, 1 kHz sweeping frequency, and 8.8 mW average optical power were obtained. The equipment consists of a fiber Bragg grating array, an optical-electronic conversion circuit, and a LabVIEW FPGA program. Every 5s, automatic feedback and PID control generate a new compensated waveform and produce a better linear sweeping than before. Compared with nonlinear sweeping, linear sweeping can reduce the cumbersome and time-consuming recalibration processes and produce more accurate measurement results.

• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.420-428
• /
• 2021

In this study, linearized sweeping of a wavelength sweeping laser was realized. This technique was used to measure the strain on a fiber Bragg grating(FBG) sensor. For linear sweeping, PID control over the wavelength difference between linear and nonlinear sweeping was employed. The performance test showed that linear sweeping with a 46 nm range and a 1 kHz frequency held up well with a 99.5 % decrement in nonlinearity after the 120th feedback. When attached to a strain gage, the FBG sensor registered strain that matched the data sheet within a difference of 4.5[με]. Altogether, linear sweeping can play a leading role in monitoring a safety of large SOC structures as well as in other wavelength sweeping laser related fields.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.293-296
• /
• 2005

This paper is concerned with the sweeping damping controller for beam. The active damping characteristics can be enhanced by moving the damper along the longitudinal axis. In this paper, the equation of motion for a beam including a sweeping damping controller is derived and its stability is proved by using Lyapunov stability theorem. It is found from the theoretical study that the sweeping damping controller can enhance the active damping characteristics, so that a single damper can suppress all the vibration modes of the beam. To demonstrate the concept of the sweeping damping control, the eddy current damper was applied to a cantilever, where the eddy current damping can move along the axis. The experimental result shows that the sweeping eddy current damper Is an effective device for vibration suppression.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.606-613
• /
• 2019

In this paper, a new method for flat sweeping automatic hold of wavelength swept laser has proposed. Through the performance test on the implemented laser, even 5 hours passed, the flat sweeping has held up well, and 56nm flat sweeping range, 1kHz sweeping frequency, and 8.8mW average optical power were obtained. This showes that the proposed can eliminate the necessity of hand-operated polarization control required for previous swept lasers in case of long time operation and also optical spectrum analyzer needed to monitor the sweeping spectrum status.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.1
• /
• pp.1187-1195
• /
• 2001

This paper presents a sweeping path planning algorithm for an autonomous smearing robot. An automatic planner generates a sweeping path pattern by proposed five basic procedures. This algorithm rocog-nizes obstacle on the architectural CAD draft and generates subgoals as tracking points which executes the area filling task based on heuristic approach. A sweeping path is planned by sequentially connecting the track-ing points in such a way that(1) the connected line segments should not be crossed, (2) the total tracking points should be as short as possible, and (3) the tracking line should not pass through the obstacle, Feasibility of the developed techniques has been demonstrated on a real architectural CAD draft.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.3
• /
• pp.521-528
• /
• 2009

This study verify the conveying characteristic and adaptability of Straight Type Seeping Auger(STSA) which is built in Combined Grain Drying and Storage System(CGDSS). It is very important to design sweeping auger which makes Combined Grain Drying and Storage System having First-In-First-Out. In order to suggest desirable idea for sweeping auger of Combined Grain Drying and Storage System, an experiment that behavior of grain on the boundary surface which is made by rotation of STSA is executed and causalities to be given problem of STSA are pointed out.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.12
• /
• pp.1210-1218
• /
• 2011

GA (Genetic Algorithms) are efficient for searching for global optima but may have some problems such as premature convergence, convergence to local extremum and divergence. These phenomena are related to the evolutionary operators. As population diversity converges to low value, the search ability of a GA decreases and premature convergence or converging to local extremum may occur but population diversity converges to high value, then genetic algorithm may diverge. To guarantee that genetic algorithms converge to the global optima, the genetic operators should be chosen properly. In this paper, we analyze the effects of the selection operator, crossover operator, and mutation operator on convergence properties, and propose the sweeping method of mutation probability and elitist propagation rate to maintain the diversity of the GA's population for getting out of the premature convergence. Results of simulation studies verify the feasibility of using these sweeping operators to avoid premature convergence and convergence to local extrema.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.173-176
• /
• 1996

The transient behavior of the complex-LMS adaptive filter is studied when the adaptive filter is operating on a fixed or sweeping complex frequency sine-wave signal. The first-order difference equation is derived for the mean weights and its closed form solution is obtained. The transient response is represented as a function of the eigenvectors and eigenvalues of input correlation matrix. The mean-square error of the algorithm is evaluated as well. An optimal convergence parameter and filter length can be determined for sweeping frequency sine-wave signals as a function of frequency change rate and signal and noise powers.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.276-281
• /
• 2014

In this research, we describe a force feedback control for industrial robots has been proposed as a system which is suitable to work utilizing pressure sensitive alternative to human. Conventionally, polished surface of the workpiece are recognized, chamfer ridge, machining processes such as deburring, and it is most difficult to automate because of its complexity, has been largely dependent on the human. To aim to build automatic vacuum system robotic force control was gripping the grinding tool, the present study we examined the adaptability to the polishing process to understand the characteristics of the control system feedback signal obtained from the force sensor mainly. Furthermore, as a field, which holds the key to the commercialization, I went ahead with the application to robotic sweeping machine. As a result, the final sweeping utilizing a robot machine to obtain a very good grinded surface was revealed.

• Journal of Sensor Science and Technology
• /
• v.26 no.1
• /
• pp.44-49
• /
• 2017

In this paper, the automatic sweep flattening for wavelength swept laser of SS-OCT has implemented. Through its performance test applied to the laser, 50 nm flat sweeping range, ${\pm}0.5dB$ fluctuation range, 22 sec the time required, and 10 mW average optical power were obtained. This shows that the realized automatic process can replace the inconvenient manual operation used for polarization control of current sweeping laser. Additionally it cuts costs for optical spectrum analyzer necessary to sweep monitoring.