• Journal of Powder Materials
• /
• v.15 no.6
• /
• pp.509-513
• /
• 2008

High-pressure abrasive entrained jet have rapidly become important machining technology over the last two decades. However, suspension jet by high-pressure has been recently developed for packaging sawing. Ideally, diamond materials should be used for components in abrasive water-jet systems that are subject to high erosive conditions. Using the diamond orifices improve maintenance and extend wear part life. This paper gives insights to using an abrasive suspension jet with diamond orifice. The influences of orifice material and orifice design are evaluated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.147-148
• /
• 2012

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.201-202
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.145-146
• /
• 2012

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.641-646
• /
• 2016

The effects of water addition on $Y_2O_3$ coatings or thick films prepared by plasma suspension spray (SPS) have been investigated. Water addition in suspension media was found to be effective to control the color of a $Y_2O_3$ coating prepared by SPS. The color changed with water addition at the shortest stand-off distance of 50 mm even if samples had the same crystalline phase. Change was not correlated with fragmentation behavior of liquid suspension inside the plasma jet. Water content over 50 vol% was found to produce unmelted particles, indicating that water suppressed heat transfer to the particles. However, plasma jet temperature was not affected. Instead, the coating fabricated with water addition has higher oxygen and lower carbon content compared to these characteristics of the coating without water addition. This was attributed to the retarded complete evaporation of liquid media from the suspension droplet, resulting in inhibition of excessive heating and evaporation of the molten $Y_2O_3$ droplet. In this regard, crystalline phase development with respect to stand-off distance and water addition was discussed.

• Journal of Forest and Environmental Science
• /
• v.34 no.5
• /
• pp.376-381
• /
• 2018

For the control of oak wilt caused by Raffaelea quercus-mongolicae, an antifungal microorganism, Streptomyces blastmyceticus, was used as a potential agent. Culture suspension of S. blastmyceticus was injected into Quercus mongolicae in the research forest of Kangwon National University by $ChemJet^{(R)}$ trunk injection and Macro-infusion at root flare injection. $Alamo^{(R)}$ (a.i., propiconazole 14.5%), a fungicide currently used for the control of oak wilt in USA, was also treated by both methods to compare the efficacy. For preventive efficacy, culture suspension of the pathogen was inoculated at 1 month after injection of either agent. Tested trees were cut at 3 months after treatment, stained with 1% Fuchsin acid, and then non-conductive area (NCA) and re-isolation frequency (RIF) of oak wilt fungus were compared among treatments. While NCA was the highest as 47.3% in pathogen only treatment, it was the lowest as 16.0% in sterilized water treatment by Macro-infusion. NCAs of Alamo treatment by Macro-infusion and ChemJet injection were 25.3% and 32.1%, respectively. NCA of S.blastmyceticus treatment by ChemJet injection was 32.3%, similar with Alamo treatment's by ChemJet injection. All treatments by either injection method showed significantly lower NCA compared to the pathogen only treatment. These results indicate that S. blastmyceticus injection shows the preventive efficacy against oak wilt disease by suppressing the growth of pathogen injected. NCA of Macro-infusion injection of sterilized water was lower as 16.0%, compared to 21.3% of ChemJet injection. It means that Macro-infusion is more effective in translocation of sterilized water than ChemJet injection by even distribution. RIF from wood discs of treated trees showed high in pathogen only treatment, but relatively low in S. blastmyceticus treatment. RIF results were correlated with NCA results. From the above results, it was confirmed that S. blastmyceticus showed preventive efficacy against oak wilt disease by ChemJet trunk or Macro-infusion at root flare injection.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.108-114
• /
• 2005

The generation of fine relics of suspensions is a significant interest as it holds the key to the fabrication of electronic devices. These processes offer opportunities for miniaturization of multilayer circuits, for production of functionally graded materials, ordered composites and far small complex-shaped components. Some novel printing methods of depositing ceramic and metal droplets were suggested in recent years. In an electro-hydrodynamic printing, the metallic capillary nozzle can be raised to several kilovolts with respect to the infinite ground plate or pin-type electrode positioned a few millimeters from the nozzle tip. Depending on the electrical and physical properties of the liquid, for a given geometry, it Is possible to generate droplets in any one of three modes, dripping, cone-jet and multi-jet. In this experiment, an alumina suspension flowing through a nozzle was subjected to electro-hydrodynamic printing using pin-type electrodes in the cone-jet mode at different applied voltages. The pin-type electrodes of 1, 100, 1000${\mu}m$ in diameter were used to form fine ceramic patterns onto the substrates. Various feature sizes with applied voltages and electrode diameters were measured. The feature sizes increased with the electrode diameter and applied voltages. The feature size was as fine as $30 {\mu}m$.

• Korean Journal of Materials Research
• /
• v.17 no.9
• /
• pp.453-457
• /
• 2007

Interest in use of ink-jet printing for pattern-on-demand fabrication of metal interconnects without complicated and wasteful etching process has been on rapid increase. However, ink-jet printing is a wet process and needs an additional thermal treatment such as an annealing process. Since a metal ink is a suspension containing metal nanoparticles and organic capping molecules to prevent aggregation of them, the microstructure of an ink-jet printed metal interconnect 'as dried' can be characterized as a stack of loosely packed nanoparticles. Therefore, during being treated thermally, an inkjet-printed interconnect is likely to evolve a characteristic microstructure, different from that of the conventionally vacuum-deposited metal films. Microstructure characteristics can significantly affect the corresponding electrical and mechanical properties. The characteristics of change in microstructure and electrical resistivity of inkjet-printed silver (Ag) films when annealed isothermally at a temperature between 170 and $240^{\circ}C$ were analyzed. The change in electrical resistivity was described using the first-order exponential decay kinetics. The corresponding activation energy of 0.44 eV was explained in terms of a thermally-activated mechanism, i.e., migration of point defects such as vacancy-oxygen pairs, rather than microstructure evolution such as grain growth or change in porosity.

• Journal of Aquaculture
• /
• v.14 no.1
• /
• pp.43-50
• /
• 2001

To study the effect of paddle wheel on water circulation, velocity components were measured in shrimp ponds both along the longitudinal direction from a single paddle wheel and at 25 grid points of two ponds, which have mean water depth of 1.2m and aspect ratio (length/width) 1.05 and 0.68, respectively. An analysis of factors related to water quality and circulation showed that I) a single paddle wheel has an effective distance of 33m for de-stratification, 16m for particulate suspension and 25m for removal of organic material, dispersion of DO and prevention of bed sediment disturbance and ii) with doubling the number of paddle wheels at the pond corners, the flow speed increased by 13% over the ponds, while it reduced by 8.5% around the pond centres. Contrary to expectation, increasing the number of paddle wheel did not generate strong circulation around the pond centre and improve water quality.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.559-560
• /
• 2006

Inkjet Printing is very attractive method for direct patterns with no masks, In order to Achieve direct printing with nano metal, It is often necessary to print them with highly concentrated Ink We research the High Concentrated silver nano ink. Formulation which has a good thermal stability and storage stability and jet stability using a ethylene glycol ether. Normally Alcohol-based inks can be sensitive But High boiling point ethylene glycol ether base Ink is creating a stable meniscus and minimum maintenance issues. We are reaching a 50~60wt% high Silver Ink using a Hydrophilic Ag Nano powder. (30~50nm)