• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.382-382
• /
• 2012

CIGS thin films have received great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films are deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. The deposition technique is one of the most important processes in preparing CIGS thin film solar cells. Among these methods, co-evaporation is one of the best technique for obtaining high quality and stoichiometric CIGS films. However, co-evaporation method is known to be unsuitable for commercialization. The sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have prepared by rf magnetron sputtering using a $Cu(In_{1-x}Ga_x)Se_2$ single quaternary target without post deposition selenization. This process has been examined by the effects of deposition parameters on the structural and compositional properties of the films. In addition, we will explore the influences of substrate temperature and additional annealing treatment after deposition on the characteristics of CIGS thin films. The thickness of CIGS films will be measured by Tencor-P1 profiler. The crystalline properties and surface morphology of the films will be analyzed using X-ray diffraction and scanning electron microscopy, respectively. The optical properties of the films will be determined by UV-Visible spectroscopy. Electrical properties of the films will be measured using van der Pauw geometry and Hall effect measurement at room temperature using indium ohmic contacts.

• Progress in Superconductivity
• /
• 제13권2호
• /
• pp.127-132
• /
• 2011

Many research groups have been manufacturing coated conductor by various processes such as PLD, MOD, and MOCVD, but the methods with production cost suitable for wide and massive application of coated conductor did not develop yet. Spray pyrolysis method adopting ultrasonic atomization was tried as one of the possible option. GdBCO precursor films have been deposited on IBAD substrate by spray pyrolysis method at low temperature and converted to GdBCO by post heat treatment. Ultrasonic atomization was used to generate fine droplets from precursor solution of Gd, Ba, and Cu nitrate dissolved in water. Primary GdBCO films were deposited at $500^{\circ}C$ and oxygen partial pressure of 1 torr. After that, the films were converted at various temperatures and low oxygen partial pressures. C-Axis oriented films were obtained IBAD substrates at conversion temperature of around $870^{\circ}C$ and oxygen partial pressures of 500 mtorr ~ 1 torr in a vacuum. Thick c-axis epitaxial film with the thickness of 0.4 ~ 0.5 ${\mu}m$ was obtained on IBAD substrate. C-axis epitaxial GdBCO films were successfully prepared by ex-situ methods using nitrate precursors on IBAD metal substrate. Converted GdBCO films have very dense microstructures with good grain connectivity. EDS composition analysis of the film showed a number of Cu-rich phase in surface. The precursor solution having high copper concent with the composition of Gd : Ba : Cu = 1 : 2 : 4 showed the better grain connectivity and electrical conductivity.

• 보존과학회지
• /
• 제36권3호
• /
• pp.213-224
• /
• 2020

본 연구에서는 여수 진남관 보수 정비 사업 중 발견된 상량문(1965년 기록)을 중심으로 재질의 성분분석 및 보존처리를 수행하였다. 상량문은 금속함에 말아 보관되어 있었으며, 결손, 변색, 경화, 이물질에 의한 손상 등이 확인되었다. X-선 형광분석(XRF) 결과 구리(Cu)로 제작된 금속함에서 기인한 녹이 상량문 표면에 고착되어 있었다. 상량문 표면에 대해 적외선분광법(FT-IR)과 열분해-GC/MS(Pyrolysis-GC/MS) 분석을 실시한 결과 카르보닐기와 지방산 화합물 등이 확인되어 상량문 표면 유기물은 기름 성분으로 확인되었다. 섬유 동정 결과 닥나무 인피섬유가 사용된 것으로 판단된다. 성분분석 및 상태조사, 접착제 예비 실험 등을 바탕으로 보존처리 재료를 선정하였으며, 닥섬유지와 메틸셀룰로오즈 등을 이용하여 보강 후 부분적으로 배접하였다.

• 마이크로전자및패키징학회지
• /
• 제23권3호
• /
• pp.69-75
• /
• 2016

무전해 Ni/전해Cr이중도금 구조에서 무전해 Ni의 결정화 열처리 조건이 Cr도금의 균열성장 및 Ni/Cr계면반응에 미치는 영향을 분석하였다. 비정질 무전해 Ni/전해 Cr 도금 후 $750^{\circ}C$에서 6시간 동안 1회 열처리한 시편을1단계 열처리 조건으로 정했다. 또한, 무전해 Ni도금 후 동일 열처리를 통해 결정화 시킨 후, 전해 Cr도금 후 한번 더 동일조건 열처리한 경우를 2단계 열처리 조건으로 정하여 상호 비교하였다. 두 가지 열처리 조건 모두에서 공통적으로 Ni/Cr계면에서 상호확산에 의한 Ni-Cr고용체band layer가 관찰되었다. 1단계 열처리 조건의 경우 Cr도금에 관통균열이 발생하였으며, 2단계 열처리 조건의 경우 Cr도금에 표면 미소균열만 형성되고 관통균열은 거의 발생하지 않았다. 이는 무전해 Ni도금 직후 열처리에 의해 Ni-P비정질 구조에서 Ni, $Ni_3P$상으로 결정화되면서 급격한 체적 감소가 발생하여 Cr층의 잔류응력 완화에 영향을 끼쳐서, 상부 전해 Cr도금의 관통균열 형성에 영향을 미치는 것으로 판단된다.

• Bulletin of the Korean Chemical Society
• /
• 제23권1호
• /
• pp.112-118
• /
• 2002

Good-to-excellent yields of 2,3-Disubstituted norbornenes (or norbornanes) were obtained using a Pd/Cu catalyzed three-component ternary coupling reaction of aryl halides, norbornadiene (or norbornene), and alkynols in toluene at $100{\circ}C$ in the presence of 5.5 M NaOH as a base and benzyltriethylammonium chloride as a phase transfer catalyst. The results of experiments using various aromatic halides suggest that the ternary coupling reaction is promoted by bromide.

• 한국재료학회지
• /
• 제11권11호
• /
• pp.923-928
• /
• 2001

An electrolytic silver plating process has been successfully developed for terminated electrode parts of dielectric ceramic resonator. High adhesion strength and high Qu is obtained and blister occurance is minimized under plating condition with $HNO_3$750 $m\ell/\ell$ and HF $ 250m\ell/\ell$ solution at $25^{\circ}C$ for 20 minutes. Adhesion strength has the highest value, 3.2 kg/mm$^2$ at etching temperature of $25^{\circ}C$. Adhesion strength, Qu and blister occurance are monotonically increased with the thickness of electrodeposition layer. In case of electrodeposition of Ag, Qu value of 380 has obtained higher than in case of electrolytic Cu plating with Qu value of 325. Therefore, terminated electrode parts of dielectric ceramic resonator reducing dielectric loss can be obtained using prensent process.

• Journal of Magnetics
• /
• 제6권4호
• /
• pp.145-147
• /
• 2001

The effect of interface roughness between [Ni/Mn] superlattice and pinned NiFe layer on magnetoresistance (MR) of [Ni/Mn] superlattice-based spin valve films was investigated. Antiferromagnetic phase structure and interface roughness of [Ni/Mn] superlattice spin valve films were compared in the as-deposited and the annealed samples at 240$\^{C}$, respectively. Surface morphology of spin valves was substantially flattened due to the formation of the antiferromatic NiMn phase. In case of Co insertion between Cu and NiFe, the interlace roughness and MR ratio in the annealed [NiMn] superlattice and pinned NiFe/Co layer increased more than those in the annealed [Ni/Mn] superlattice and pinned NiFe layers respectively.

• 보존과학연구
• /
• 통권23호
• /
• pp.149-162
• /
• 2002

Gilt bronze locks(Treasure No. 1141) excavated from Hancheonsa temple are artifacts of Goryeo Dynasty. The locks underwent a conservation process from October 2001 to July 2002. The process included cleaning and the application of corrosion inhibitors, Benzotriazolesolution, as well as reinforcement treatment with Paraloid NAD-10 solution,an acrylic resin. Non-destructive XRF analysis unveil that the artifacts are made of an alloy of copper(Cu), tin(Sn) and lead(Pb), but the gilt layer is too thin to analyze the purity of the gold or the exact production method. Gilt bronze locks are important materials because they preserve all the structures of locks in Goryeo Dynasty to the smallest detail. The surface pattern is revealed through the conservation process and components of the alloy through material analysis.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.283-283
• /
• 2013

Because of beautiful glossy and color, the value of gold leverage is very high in Europe. To improve the quality of gold alloys, we performed heat treatment on 14 K white gold alloys by variously changing age-hardening conditions. Age-hardening behavior and the related phase transformation changes were studied to elucidate the hardening mechanism of 14 K white gold alloy. For solid solution treatment [ST], casted gold alloy specimens were treated at high temperature ($750^{\circ}C$) for 30 minutes, and the specimens dropped to water to quench them. For Age-hardening treatment [AT], the specimens were treated at various temperatures ($250{\sim}300^{\circ}C$). After the heat treatment, we observed the phenomenon to increase hardness from 126 Hv to 166 Hv by Vicker's hardness tester. Through electron probe micro-analysis (EPMA) mapping analysis, we investigated that irregular particles were changed uniformly. In the SEM and OM images, two phases of matrix and particle-likestructures were observed, and the precipitation of these elements from the matrix progressed during age-hardening. By transmission electron microscope and X-ray diffraction observation, it was revealed that the formation of the Au3Cu superstructure contributed to the age-hardening at $270^{\circ}C$ in the gold alloy. After the heat treatment, this analysis shows that casted gold alloys were to improve hardness and to moderate surface defects at specific temperatures and duration.

• 한국표면공학회지
• /
• 제48권1호
• /
• pp.11-22
• /
• 2015

Pd alloy hydrogen membranes for hydrogen purification and separation need thermal stability at high temperature for commercial applications. Intermetallic diffusion between the Pd alloy film and the porous metal support gives rise to serious problems in long-term stability of Pd alloy membranes. Ceramic barriers are widely used to prevent the intermetallic diffusion from the porous metal support. However, these layers result in poor adhesion at the interface between film and barrier because of the fundamentally poor chemical affinity and a large thermal stress. In this study, we developed Pd alloy membranes having a dense microstructure and saturated composition on modified metal supports by advanced DC magnetron sputtering and heat treatment for enhanced thermal stability. Experimental results showed that Pd-Cu and Pd-Ag alloy membranes had considerably enhanced long-term stability owing to stable, dense alloy film microstructure and saturated composition, effective diffusion barrier, and good adhesive interface layer.