• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.1
• /
• pp.134-141
• /
• 2016

Dampening in printing is not only used with plain water but also used with various substances like dampening additive, in order to improve the wetting property by lowering the surface tension and to control material for modifing the ink transfer characteristic with proper emulsification. We have studied the printing quality according to these, looking into interrelationship among the dampening solution's pH, electrical conductivity and IPA content, prescribing the proper usage and minimum usage of fountain solution and dampening additive. In this study, it shows good result when mixing at the 7 wt% dampening with additive solution, which is result from the color density of printed sheets in accordance with the change of dampening solution condition. And the printed density value calculated 1 hour after printing, it shows relatively safe value at the etch liquid 4 wt% and IPA addition 2 wt%. The dry down at this test showed similar results regardless of various dampening conditions on coated paper, but in case of uncoated paper, the dry down showed a quite gap of different due to the fast penetration to the paper.

• Textile Coloration and Finishing
• /
• v.17 no.3 s.82
• /
• pp.8-15
• /
• 2005

Cationic dyeable polyester(CDP) fabric was annealed at varying temperatures range from $120^{\circ}C$ to $220^{\circ}C$ for 1, 3, and 5 min under tension. Dyeing rates of CDP fabrics were measured with cationic and disperse dyes at $100^{\circ}C$ and $120^{\circ}C$ in water system. Also X-ray diffraction pattern, DSC thermograms and dyeability of fabric with cationic and disperse dyes were investigated. The intensities of X-ray diffraction peaks of annealed fabric were increased with increasing in annealed temperature, and peak became sharp with heat setting temperature. The apparent color depth (K/S) of CDP fabric initially decreased with increase of heat-setting temperature up to $160\~180^{\circ}C$ and then increased at higher temperature. The shearing modulus(G) and surface roughness were increased with annealing temperature.

• Journal of ILASS-Korea
• /
• v.16 no.1
• /
• pp.1-6
• /
• 2011

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPG (Liquefied Petroleum Gas) which is able to meet the limits of better emission levels without many modifications to current engine design. LPG has a high vapor pressure and lower viscosity and surface tension than diesel and gasoline fuels. These different fuel characteristics make it difficult to directly apply the conventional gasoline or diesel fuel pump. Self acting lubricated groove design or coating can be used in high-speed and high precision spindle system like a roller-vane type fuel pump, because of its advantages such as low frictional loss, low heat generation, averaging effect leading better running accuracy and simplicity in manufacturing. Those design method can also affect the atomization of fuel from the injector and the formation of fuel film on the intake manifold. In this study, experiments are carried out to get performance characteristics of initial and steady state operation, The characteristics of vane type fuel pump were investigated to access the applicability on LPLi engine.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.25 no.1
• /
• pp.109-120
• /
• 2007

In gravure printing, the amount of ink fill into the cells has a great effect on the qualities of final printed products. And printability of final products is determined by every kinds of variables. Ink transfer process is not verified scientifically because gravure cell is small and printing speed is rapid. In order to understand the ink transfer mechanism of conventional gravure, this study is performed using the Computational Fluid Dynamics Evaluation. Flow-3D simulation software is used for considering of Newtonian flow. Among the various factors, this study have dealt with gravure cell types used computer simulation in order to define distinctive features in ink flow in the cell. The results of simulation, it defined the distribution of pressure, speed, stream function, viscosity, shear rate, surface tension during the gravure printing. It is founded out the difficulties and characteristics according to the printing speed and viscosity of Gravure ink.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.76-81
• /
• 2002

The dramatic increase in the depth of a weld bead penetration has been demonstrated by welding a stainless steel in GTA (Gas-Tungsten-Arc) process with activating flux which consists of oxides and halides. However, there is no commonly agreed mechanism fer the effect of flux on the process. In order to make clear the mechanism, each behavior of the arc md the weld pool in GTA process with activating flux is observed in comparison with a conventional GTA process. A constricted anode root is shown in GTA process with the activating flux, whereas a diffuse anode root is shown in the conventional process. These anode roots are related strongly to metal vapor from the weld pool and the metal vapor is also related to temperature distributions on the weld pool surface. Furthermore, it is suggested that a balance between the Marangoni force and the drag force of the cathode jet should dominate the direction of re-circulatory flow in the weld pool. The electromagnetic force encourages the inward re-circulatory flow due to the constricted anode root in the case with flux. The difference in flow direction in the weld pool changes the geometry or depth/width ratio of weld bead penetration.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.211-216
• /
• 2001

Flow motion and variation of thermal field around a bubble which attached at the upper cooled solid wall in a $B\dot{e}nard$ convection flow is studied experimentally using thermo-sensitive liquid-crystal tracers and image processing for flow visualization and analysis. The air is injected gradually by $0.1m\ell$ to make the bubble. As the growing of the bubble in a $B\dot{e}nard$ convection flow, the variation of temperature field and surface tension along the bubble, which in turn cause to change the thermal field patterns and the flow direction and patterns. 6 cells flow pattern is transformed into diverse flow pattern. At the large size of a bubble, it's only conduction mechanism under the region of the bubble because of low Ra number 1137, but the convection flow both sides of the bubble leads to another convection flow in the bubble influence area which has been remained stable stagnation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.4
• /
• pp.313-319
• /
• 2007

The effect of capillary cross-section geometry on evaporation is investigated in terms of the meniscus shape, evaporation rate and evaporation-induced flow for circular, square and rectangular cross-sectional capillaries. The shapes of water and ethanol menisci are not much different from each other in square and rectangular capillaries even though the surface tension of water is much larger than that of ethanol. On the other hand, the shapes of water and ethanol menisci are very different from each other in circular capillary. The averaged evaporation fluxes in circular and rectangular capillaries are measured by tracking the meniscus position. At a given position, the averaged evaporation flux in rectangular capillaries is much larger than that in circular capillary with comparable hydraulic diameter. The flow near the evaporating meniscus is also measured using micro-PIV, so that the rotating vortex motion is observed near the evaporating ethanol and methanol menisci except for the case of methanol meniscus in rectangular capillary. This difference is considered to be due to the existence of corner menisci at the four comers.

• Journal of Welding and Joining
• /
• v.26 no.6
• /
• pp.67-73
• /
• 2008

Three-dimensional transient simulation of laser-GMA hybrid welding involving multiple physical phenomena is conducted neglecting the interaction effect of laser and arc heat sources. To reproduce the bubble and pore formations in welding process, a new bubble model is suggested and added to the established laser and arc welding models comprehending VOF, Gaussian laser and arc heat source, recoil pressure, arc pressure, electromagnetic force, surface tension, multiple reflection and Fresnel reflection models. Based on the models mentioned above, simulations of laser-GMA hybrid butt welding are carried out and besides the molten pool flow, top and back bead formations could be observed. In addition, the laser induced keyhole formation and bubble generation duo to keyhole collapse are investigated. The bubbles are ejected from the molten pool through its top and bottom regions. However, some of those are entrapped by solid-liquid interface and remained as pores. Those bubbles and pores are intensively generated when the absorption of laser power is largely reduced and consequently the full penetration changes to the partial penetration.

• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.6
• /
• pp.724-730
• /
• 2004

Effects of the biosurfactant produced by Rhodococcus erythropolis on the solubilization and biodegradation of phenanthrene were investigated. Based on surface tension measurements, the average critical micelle concentration of the biosurfactant was estimated to be about 16mg TOC/L. The apparent solubility of phenanthrene increased linearly with the addition of biosurfactants above the CMC, and the concentration of solubilized phenanthrene was 38.9mg/L in 322mg TOC/L biosurfactant solution. The weight-solubilization ratio of biosurfactants for phenanthrene was approximately 118.8mg/g, this value was over 5 times greater than that of sodium dodecyl sulfate. Using a known phenanthrene degrader, batch phenanthrene biodegradation experiments were conducted with and without biosurfactants in liquid culture. The rate and extent of phenanthrene mineralization by the phenanthrene degrader with biosurfactants were much greater than those without biosurfactants. The greater phenanthrene mineralization observed in the presence of biosurfactants is attributed to the increased phenanthrene concentration in the aqueous culture due to the partitioning of the compound to biosurfactant micelles. The biosurfactant did not exhibit any toxic effect on mineralization of glucose by the phenanthrene-degrader.

• Smart Structures and Systems
• /
• v.1 no.4
• /
• pp.385-404
• /
• 2005

The paper presents a model to calculate reinforcement strain using measured crack width in members under applied tension, flexure, and/or shear stress. Crack mapping using a new type of distributed coaxial cable sensors for health monitoring of large-scale civil engineering infrastructure was recently proposed and developed by the authors. This paper shows the results and performance of such sensors mounted on near surface of two flexural beams and a large scale reinforced concrete box girder that was subjected to cyclic combined shear and torsion. The main objectives of this health monitoring study was to correlate the sensor's response to strain in the member, and show that magnitude of the signal's reflection coefficient is related to increases in applied load, repeated cycles, cracking, and reinforcement yielding. The effect of multiple adjacent cracks, and signal loss was also investigated. The results shown in this paper are an important step in using the sensors for crack mapping and determining reinforcement strain for in-situ structures.