• 한국해양공학회지
• /
• 제3권2호
• /
• pp.625-625
• /
• 1989

To check technical improvement in the soundness and strength of 12% Cr steel rotor, a 25 tons of rotor with 65 tons of ingot was made in real size and was cut to pieces to take test samples, and the various mechanical tests such as impact, tensile, creep, and fatigue were carried out. The strengths are compared with those of 1% Cr-Mo-V rotor of same size. Microstructures of the samples are examined and reviewed. The results can be summarized as follows. 1) Fracture appearance transition temperatures are 80.deg. C at the center part and 60.deg. C near surface of 12% Cr rotor, and 8.deg. C near surface of 1% Cr-Mo-V rotor. 2) Comparative rapid softening occurs at higher temperatures above 600.deg. C for 12% Cr steel and 550.deg. C for 1% Cr-Mo-V steel in tension tests. 3) Fatigue crack propagation rate of 12% Cr steel is almost same as that of 1% Cr-Mo-V steel at the same corresponding surface part of the rotors. The crack growth rate of center part of 12% Cr rotor is faster than near surface part of the rotor, and the crack growth rate at the load condition of R=0.04 is slower than that of the load condition of R=0.5 for both 12% Cr steel and 1% Cr-Mo-V steel. 4) Crack growth rate of radial direction near surface of 12% Cr rotor is faster than that of transverse direction at the same part because of the difference in residual stresses. 5) Both creep and fatigue strengths of 12% Cr steel are superior to those of 1% Cr-Mo-V steel and the difference is thought the effect of climb and glide controlled creep by solid solution of alloying elements and dispersion of carbides.

• 한국농공학회논문집
• /
• 제64권2호
• /
• pp.37-45
• /
• 2022

In-situ pilot experiment was carried out to establish a countermeasure on the soil loss from the hill side uplands that was rehabilitated by soil remediation method nearby abandoned mine sites for 2 years. It was considered that the affect of an inclination of cover surface, a stabilization treatment of cover layer by lime and steel refining slag (SRS) and a vegetation of soil surface as an effect factors in the experiment. It was constructed 4 lysimeters (plots, 22 m long, 4 m width) on the hilly side (37% inclination). One plot was control and two plots was treated by 1% lime and SRS. A remind one plot was modified a inclination to 27% to compare the affect of inclination on the amount of cover soil loss. It was attached a reservior tank and water level gauge in the end of lysimeters to measure the amount of the surface water flow and soil loss. It was also installed the automated sensors that could be collect the precipitation, soil moisture content, tension of cover layer in each plots. It was observed that the event of precipitation were caused the soil loss and it were related the physical and chemical properties of cover soil and inclination of surface layer of plots. During the experiment, it was exceeded the national regulation (50 t/ha/yr) in 37% inclination plots even though it was vegetated on the cover soil surface. However, in 27% inclination plot, it was shown that the amount of soil loss was maintained below the national regulation and, more ever, vegetation could reduce the the amount of soil loss. Therefore it was expected that such results could be applied to the future design of rehabilitation projects on the polluted farmland nearby abandoned mine sites.

• 한국산학기술학회논문지
• /
• 제16권9호
• /
• pp.5756-5762
• /
• 2015

본 논문에서는 자연에서 영감을 얻은 생체 모방 공학 중의 하나인 연잎 효과에 초점을 맞추었다. 생체 모방 공학은 자연의 시스템을 관찰하여 동식물, 곤충 등의 구조와 기능을 모방하여 공학적으로 활용하는 것이다. 나노 기술의 발전은 생체 모방 공학의 발전도 함께 일으켜왔다. 본 과제에서는 연잎 표면의 소수성과 특징에 대해 살펴본 뒤 나노 측정 장비인 SEM (주사선전자 현미경)과 AFM (원자력간 현미경)을 이용하여 측정 후 비교, 분석하였다. 연잎의 표면에는 수많은 나노 돌기들이 존재하며, 그 작은 돌기들이 소수성을 갖게 하고 표면장력을 극대화 시키는 역할을 한다. 연잎의 표면에서는 물방울이 동그랗게 모여 있는 것을 볼 수 있는데 그것을 연잎 효과라고 하며, 나노 돌기로부터 생성된 효과이다. 이러한 연잎의 표면을 배율 별로 2D와 3D로 측정하여 분석하였다. 또한, 그 결과를 기존의 법칙들에 어떻게 적용되는지 살펴보았으며 나아가 소수성을 판별할 수 있는 새로운 방법에 대해 논의하여 보고자 하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권1호
• /
• pp.147-153
• /
• 2019

구조물의 보강을 위해 프리스트레스 강선에는 인장력이 도입되는데 이 강선은 덕트 및 편향장치에 의해서 휨을 동시에 받게 된다. 이와 같이 인장과 휨을 동시에 받는 프리스트레스 강선의 굴절인장성능을 평가하기 위해 강선의 직경, 맨드럴 직경, 맨드럴과 강선 사이 마찰계수를 변수로 하여 총 600종에 대한 굴절인장 변수해석을 실시하였다. 해석 결과, 강선의 직경이 클수록 낮은 굴절인장성능을 나타내었고, 그 영향은 강선 연신율의 증가에 따라 감소하였다. 강선의 굴절인장성능에 대한 맨드럴 직경, 맨드럴-강선 간 마찰계수의 영향은 매우 작게 나타났지만, 맨드럴-강연선 간 마찰계수에 대한 추가 해석 결과 상대적으로 높은 상관성을 보였다. 따라서, 굴절인장성능 확보를 위해서는 충분한 연신율 확보가 우선되어야 하고, 연신율 확보에 제약이 있을 시 적정값까지 강선 직경을 감소시켜야 하겠으며, 강선의 표면조건을 조절하여 강선 간 마찰력을 높여야 할 것이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2648-2653
• /
• 2007

Recently, increasing demand on not only lighter but also extremely mobile battery make micro fuel cell device very attractive alternative. By reducing the size of fuel cell, surface tension becomes dominant factor with minor gravitational effect. Therefore, it is very difficult to detach the $CO_2$ bubble generating on a cathode side in ${\mu}DMFC$ (micro direct methanol fuel cell). The degassing of a $CO_2$ bubble has drawn quite attention especially for ${\mu}DMFC$ due to its considerable effect on overall machine performance. Our attention has been paid to the dynamic behavior of immiscible bubble attached to the one side of the wall on 2D rectangular channel subject to external shear flow. We use Level Contour Reconstruction Method (LCRM) which is simplified version of front tracking method to track the bubble interface motion. Effects of Reynolds number, Weber number, advancing/receding contact angle and property ratio on bubble detachment characteristic has been numerically identified.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.1882-1887
• /
• 2007

In the present experimental study, the effect of interfacial tensions on pressure drop of air-water two-phase flow in round mini-channels was investigated. A glass (highly wettable) tube and a Teflon (poorly wettable) tube, both in 350 mm length but 1.8 mm and 1.59 mm in inner diameters each, were used for the tests. All the experiments were performed only in the plug flow regime, confirmed by visualization. In the glass tube, the gas plugs were surrounded by the liquid film along the inner periphery. On the other hand, the inner wall remained dry at the gas portion in the Teflon tube. The pressure drop of the plug flow in the Teflon tube without the liquid film) appeared much larger than in the glass tube (with the liquid film) due to dissipation of energy by movement of the wetting lines. In this paper, various correlations on the two-phase pressure drop of plug flows were compared and a modified correlation was proposed, taking account of the surface wettability.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.99-106
• /
• 2006

High velocity oxygen-fuel thermal spray coating of the WC-Co cermet material is a well-established process for modifying the surface properties of the structural components exposed to the corrosive and wear attacks, and also these coating are well-known method to improve the fatigue strength of material. In this study, HVOF coated SM490B are prepared to evaluation of the effect of coating on tension and fatigue crack growth behavior. The pre-crack of the fatigue crack growth test specimens machined at deposited material area, heat affected zone and boundary, respectively. Through these test, the following results are obtained: 1) Tensile strength was about 498 MPa, and fracture occurred on base metal area. 2) The fatigue crack of coated specimens propagated more rapidly than non-coated specimen in all specimens. 3) In the same coating thickness specimens, the specimens with pre-crack at boundary more rapidly propagated than the specimens with pre-crack at HAZ and deposited material area. These results can be used as basic data in a structural integrity evaluation of rolled SM490B weldments considering HVOF coating.

• The Korean Journal of Physiology
• /
• 제10권1호
• /
• pp.7-14
• /
• 1976

The Present study was conducted to investigate the effects of Ginseng extract on the tension-area curve for stearic acid monolayer. At the same time, the effects of Ginseng extract on osmotic and mechanical fragility of human red cells and histamine release from rabbit leukocytes were studied, The results are summarized as follows. 1. The Ginseng alcohol extract was found to expand liquid expanded phase of stearic acid monolayer, thus it is speculated that this agent may be acting as a surface active substance. 2. Osmotic hemolysis was inhibited by the Ginseng alcohol extract and the same effect was also observed in the presence of Ginseng saponin. However, the Ginseng alcohol extract was found to decrease hematocrit ratio of the RBC suspension, therefore, the inhibition of the osmotic hemolysis by this agent may be secondary effect to the reduced cell volume. 3. The mechanical hemolysis was also inhibited by the Ginseng alcohol extract but the inhibition was independent of changes in hematocrit ratio. 4. Histamine release from rabbit leukocytes was significantly increased in vitro in the presence of the Ginseng alcohol extract.(p<0.05)

• 한국정밀공학회지
• /
• 제33권3호
• /
• pp.217-223
• /
• 2016

In this paper, the movement of a liquid metal droplet in a channel by continuous electrowetting effect is analyzed. The channel is fabricated using two glass substrates and silicone rubber as spacers, and a mercury droplet and dilute sulfuric acid are added into the channel. The droplet is moved according to voltage applied at both ends of the channel through an electrolyte. According to the shape of the droplet and the applied voltage, the velocity of the droplet is changed. The velocity is proportional to the applied voltage and inversely proportional to the length of the droplet, both theoretically and experimentally. Contact angle hysteresis and a meniscus change were also found in the moving state. This implies the existence of a threshold in movement by Laplace pressure difference. The experiment indicated that the sliding angle was inversely proportional to the width of the droplet but that the voltage threshold was proportional to the width.

• Structural Engineering and Mechanics
• /
• 제53권5호
• /
• pp.867-880
• /
• 2015

Mechanical fastening is still one of the main methods used for joining components. Different techniques have been applied to reduce the effect of stress concentration of notches like fastener holes. In this work we evaluate the feasibility of combining laser shock peening (LSP) and cold expansion to improve fatigue crack initiation and propagation of open hole specimens made of 6061-T6 aluminum alloy. LSP is a new and competitive technique for strengthening metals, and like cold expansion, induces a compressive residual stress field that improves fatigue, wear and corrosion resistance. For LSP treatment, a Q-switched Nd:YAG laser with infrared radiation was used. Residual stress distribution as a function of depth was determined by the contour method. Compact tension specimens with a hole at the notch tip were subjected to LSP process and cold expansion and then tested under cyclic loading with R=0.1 generating fatigue cracks on the hole surface. Fatigue crack initiation and growth is analyzed and associated with the residual stress distribution generated by both treatments. It is observed that both methods are complementary; cold expansion increases fatigue crack initiation life, while LSP reduces fatigue crack growth rate.