• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1172-1179
• /
• 2020

As a Lagrangian particle method, Moving Particle Semi-implicit (MPS) method has great capability to capture interface/surface. In recent years, the multiphase flow simulation using MPS method has become one of the important directions of its developments. In this study, some key methods for multiphase flow have been introduced. The interface tension model in multiphase flow is modified to maintain the smooth of the interface and suitable for the three-phase flow. The mass transfer at immiscible liquid interface entrained by single bubble which could occur in Molten Core-Concrete Interaction (MCCI) has been investigated using this particle method. With the increase of bubble size, the height of entrainment column also increases, but the time of film rupture is slightly different. With the increase of density ratio between the two liquids, the height of entrained column decreases significantly due to the decreasing buoyancy of the denser liquid in the lighter liquid. In addition, the larger the interface tension coefficient is, the more rapidly the entrained denser liquid falls. This study validates that the MPS method has shown great performance for multiphase flow simulation. Besides, the influence of physical parameters on the mass transfer at immiscible interface has also been investigated in this study.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.1
• /
• pp.71-83
• /
• 2009

Shotcrete is an important primary support for tunnelling in rock. The quality control of shotcrete is a core issue in the safe construction and maintenance of tunnels. Although shotcrete may be applied well initially onto excavated rock surfaces, it is affected by blasting, rock deformation and shrinkage and can debond from the excavated surface, causing problems such as corrosion, buckling, fracturing and the creation of internal voids. This study suggests an effective non-destructive evaluation method of the tunnel shotcrete bonding state applied onto hard rocks using the impact-echo (IE) method and ground penetration radar (GPR). To verify previous numerical simulation results, experimental study carried out. Generally, the bonding state of shotcrete can be classified into void, debonded, and fully bonded. In the laboratory, three different bonding conditions were modeled. The signals obtained from the experimental IE tests were analyzed at the time domain, frequency domain, and time-frequency domain (i.e., the Short- Time Fourier transform). For all cases in the analyses, the experimental test results were in good agreement with the previous numerical simulation results, verifying this approach. Both the numerical and experimental results suggest that the bonding state of shotcrete can be evaluated through changes in the resonance frequency and geometric damping ratio in a frequency domain analysis, and through changes in the contour shape and correlation coefficient in a time-frequency analysis: as the bonding state worsens in hard rock condition, the autospectral density increases, the geometric damping ratio decreases, and the contour shape in the time-frequency domain has a long tail parallel to the time axis. The correlation coefficient can be effectively applied for a quantitative evaluation of bonding state of tunnel shotcrete. Finally, the bonding state of shotcrete can be successfully evaluated based on the process suggested in this study.

• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.3-11
• /
• 2009

The increased demand and consumption of coal has intensified problems associated with disposal of solid waste generated in utilization of coal. Major utilization of coal by-products has been in construction-related applications. Since fly ash accounts for the part of the production of utility waste, the majority of scientific investigations have focused on its utilization in a multitude of use, while little attention has been directed to the use of bottom ash. As a consequence of this neglect, a large amount of bottom ash has been stockpiled. However, the need to obtain safe and economical solution for its proper utilization has been more urgent. The study presented herein is designed to ascertain the performance characteristics of bottom ash, as autoclaved lightweight foamed concrete product. The laboratory test results indicated that tobermorite was generated when bottom ash was used as materials for hydro-thermal reaction. According to the analysis of variance, at the fresh state, water ratio affects on flow and slurry density of autoclaved lightweight foamed concrete, but foam ratio influences on slurry density, while, at the hardened state, foam ratio affects on the density of dry and the compressive strength but doesn't affect on flexural and tensile strength. In the results of response surface analysis, to obtain target performance, the most suitable mix condition for lightweight foamed concrete using bottom ash was water ratio of 70$\sim$80% and foaming ratio of 90$\sim$100%.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.100-104
• /
• 2008

Titanium sheet metal substrates used in thin film batteries were wet etched and their surface area was increased in order to increase the discharge capacity and power density of the batteries. To obtain a homogeneous etching pattern, we used a conventional photolithographic process. Homogeneous hemisphere-shaped wells with a diameter of approximately $40\;{\mu}m$ were formed on the surface of the Ti substrate using a photo-etching process with a $20\;{\mu}m{\times}20\;{\mu}m$ square patterned photo mask. All-solid-state thin film cells composed of a Li/Lithium phosphorous oxynitride (Lipon)/$LiCoO_2$ system were fabricated onto the wet etched substrate using a physical vapor deposition method and their performances were compared with those of the cells on a bare substrate. It was found that the discharge capacity of the cells fabricated on wet etched Ti substrate increased by ca. 25% compared to that of the cell fabricated on bare one. High discharge rate was also able to be obtained through the reduction in the internal resistance. However, the cells fabricated on the wet etched substrate exhibited a higher degradation rate with charge-discharge cycling due to the nonuniform step coverage of the thin films, while the cells on the bare substrate demonstrated a good cycling performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.1
• /
• pp.61-69
• /
• 1998

Vapor Axial Deposition (VAD), one of optical fiber preform fabrication processes, is performed by deposition of submicron-size silica particles that are synthesized by combustion of raw chemical materials. In this study, flow field is assumed to be a forced uniform flow perpendicularly impinging on a rotating disk. Similarity solutions obtained in our previous study are utilized to solve the particle transport equation. The particles are approximated to be in a polydisperse state that satisfies a lognormal size distribution. A moment model is used in order to predict distributions of particle number density and size simultaneously. Deposition of the particles on the disk is examined considering convection, Brownian diffusion, thermophoresis, and coagulation with variations of the forced flow velocity and the disk rotating velocity. The deposition rate and the efficiency directly increase as the flow velocity increases, resulting from that the increase of the forced flow velocity causes thinner thermal and diffusion boundary layer thicknesses and thus causes the increase of thermophoretic drift and Brownian diffusion of the particles toward the disk. However, the increase of the disk rotating speed does not result in the direct increase of the deposition rate and the deposition efficiency. Slower flow velocity causes extension of the time scale for coagulation and thus yields larger mean particle size and its geometric standard deviation at the deposition surface. In the case of coagulation starting farther from the deposition surface, coagulation effects increases, resulting in the increase of the particle size and the decrease of the deposition rate at the surface.

• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1513-1522
• /
• 2018

Bismuth telluride ($Bi_2Te_3$) thin films were prepared with various electrolyte temperatures ($10^{\circ}C-70^{\circ}C$) and concentrations [$Bi(NO_3)_3$ and $TeO_2:1.25-5.0mM$] in this study. The surface morphologies differed significantly between the experiments in which these two electrodeposition conditions were separately adjusted even though the applied current density was in the same range in both cases. At higher electrolyte temperatures, a dendrite crystal structure appeared on the film surface. However, the surface morphology did not change significantly as the electrolyte concentration increased. The dendrite crystal structure formation in the former case may have been caused by the diffusion lengths of the ions increasing with increasing electrolyte temperature. In such a state, the reactive points primarily occur at the tops of spiked areas, leading to dendrite crystal structure formation. In addition, the in-plane thermoelectric properties of $Bi_2Te_3$ thin films were measured at approximately 300 K. The power factor decreased drastically as the electrolyte temperature increased because of the decrease in electrical conductivity due to the dendrite crystal structure. However, the power factor did not strongly depend on the electrolyte concentration. The highest power factor [$1.08{\mu}W/(cm{\cdot}K^2$)] was obtained at 3.75 mM. Therefore, to produce electrodeposited $Bi_2Te_3$ films with improved thermoelectric performances and relatively high deposition rates, the electrolyte temperature should be relatively low ($30^{\circ}C$) and the electrolyte concentration should be set at 3.75 mM.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.886-893
• /
• 2001

We synthesized $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_{3-\delta}$ powders by coprecipitation, citration and solid-state reactions. The oxygen permeation membranes were fabricated by cold isostatic pressing of the synthesized powders, followed by sintering in air. All powders and membranes consist of perovskite phases. The coprecipitated powders showed the highest surface area ($7.5m^2/g$) but strontium deficiency was found during washing and filtering in the process. The membrane with lower relative density was fabricated by citration method. On the other hand, solid state reacted powders had high relative density (95%), and mechanical properties showed superior properties. Especially, the composition of the solid-state reacted powders was relatively well-controlled.

• Korean Journal of Soil Science and Fertilizer
• /
• v.30 no.3
• /
• pp.234-241
• /
• 1997

The effects of bulk densities(${\rho}_b$) on saturated hydraulic conductivity (Ksat) and solute elution patterns were investigated from five different bulk densities ranging from $1.1Mg/m^3$ to $1.5Mg/m^3$ with each increment of $0.1Mg/m^3$. The hydraulic conductivities observed were divided into two stages: (1) a linearly decrease with increase in bulk density up to $1.4Mg/m^3$, (2) a steady state where the bulk density is greater than $1.4Mg/m^3$. Using the saturated hydraulic conductivity at the steady state, we figured out the equation describing the correlation between bulk densities(${\rho}_b$) and saturated hydraulic conductivity(Ksat) as follows: $Ksat=-19.2({\rho}_b{^2})+6{\rho}_b+15.5$, (r=0.985). Electrical conductivity(EC) measured from the leachate of the soil column showed that EC at the same pore volume were decreased with an increase in the bulk density from $1.2g/cm^3$, $1.5g/cm^3$, as shown in the time taken to collect the same pore volume at each respective bulk density. The maximum relative concentrations (C/Co=1) from the breakthrough curves for the anions of $Cl^-$, $NO_3{^-}$ and $SO_4{^{2-}}$, which are weakly adsorbed on the soil particles, moved to the right of the graph, while a distinctive retardation occurs at the bulk density between $1.3Mg/m^3$ and $1.4Mg/m^3$. The time taken to recover about 90% of indigenous sulphate was approximately twice as those of chloride and nitrate, resulting in slightly stronger adsorption characteristics for sorption sites on the soil surface. Thus, we can conclude that the salt accumulation in green house soil might be significantly influenced by it's bulk density at the soil depth, as well as the adsorption capacity of ions for the sorption sites in soils.

• Ocean and Polar Research
• /
• v.32 no.2
• /
• pp.123-135
• /
• 2010

Around Tongyeong coasts which located in southern coast of Korea composed to the complex coastal line and scattered by small islands. It also has been distributed to a complicated bathymetric structure by several types of channels. This study carried to analyze the spatial characteristics of macrobenthic community and benthic environmental variance on sub-tidal area based on multivariate statistics tools. Sediment composition varied from muddy sand to mud, and along the channels, it composed to a heterogeneous bottoms mixed by shell fragment, cobbles and mud. Organic contents on the surface sediment varied 1.1-3.9%. Total of 272 species, $33,349\;ind./m^2$ of macrobenthos identified in all of sample area. Polychaetes also prevailed among the specimen. L. longifolia, P. pinnata dominated based on density. Considering on the biomass, echinoderm S. lacunosa, A. tricoides listed. Closer to the coastal area, the density and diversity were higher. Community structure based on cluster analysis was discriminated into three groups. Each group was also characterized by geographical state such as depth, sediment composition. In addition, when applied to the bathymetric data, the channel, which composed to the mixed sediment, made a role of limited factor which characterized to benthic community. Because the specimen around the channel have been affected on the diverse sediment mixture. Most of benthic studies in the southern coast of Korea focused to the condition of benthic organic pollution spatially, because along the coast, it also developed a aquaculture ground and industrial complex. But, as results, most of the area, it turn out the less polluted areas nevertheless similar environment situation. It supposed that benthic community affect to the bottom sediment composition by physical characteristics.

• Investigative Magnetic Resonance Imaging
• /
• v.24 no.3
• /
• pp.95-122
• /
• 2020

In this article, we evaluated the performance of radiofrequency (RF) coils in terms of the signal-to-noise ratio (S/N) and homogeneity of magnetic resonance images when used for ultrahigh-frequency (UHF) 7T magnetic resonance imaging (MRI). High-quality MRI can be obtained when these two basic requirements are met. However, because of the dielectric effect, 7T magnetic resonance imaging still produces essentially a non-uniform magnetic flux (|B₁|) density distribution. In general, heterogeneous and homogeneous RF coils may be designed using electromagnetic (EM) modeling. Heterogeneous coils, which are surface coils, are used in consideration of scalability in the |B₁| region with a high S/N as multichannel loop coils rather than selecting a single loop. Loop coils are considered state of the art for their simplicity yet effective |B₁|-field distribution and intensity. In addition, combining multiple loop coils allows phase arrays (PA). PA coils have gained great interest for use in receiving signals because of parallel imaging (PI) techniques, such as sensitivity encoding (SENSE) and generalized autocalibrating partial parallel acquisition (GRAPPA), which drastically reduce the acquisition time. With the introduction of a parallel transmit coil (pTx) system, a form of transceiver loop arrays has also been proposed. In this article, we discussed the applications and proposed designs of loop coils. RF homogeneous coils for volume imaging include Alderman-Grant resonators, birdcage coils, saddle coils, traveling wave coils, transmission line arrays, composite right-/left-handed arrays, and fusion coils. In this article, we also discussed the basic operation, design, and applications of these coils.