• Journal of the Korean Society of Combustion
• /
• v.18 no.2
• /
• pp.23-31
• /
• 2013

Compact steam boiler is a useful heat exchanger in a space-intensive system. There are some constraints in terms of sizing and designing the space confined in the system which is usually used in vessels. In this study, design considerations for heavy duty heat exchangers of compact steam boilers are presented and evaluated. Especially, evaporator tubes of marine boiler which are exposed to a high temperature environment are considered. Also, extended surface designs with a high temperature are examined. In order to determine the criteria with considerations of both heat transfer rate and pressure drop in the heat exchanger, they are evaluated with major variables, such as the tube diameter, the number of tubes, and the tube length. Finally, the design parameters are estimated as the bare tubes are installed instead of the finned tubes.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.1
• /
• pp.11-18
• /
• 1993

Autopolymerising and visible light cured resin are used to reline dentures. But relined surface are easily contaminated by water or saliva in the mouth during clinical procedure. This study was to find out the effect of surface contamination on the transverse strength of the relined denture base. To accomplish this, the specimens of $65\times10\times3mm$ were made with heat-cured(Lucitone 199), visible light-cured(Triad), and autopolymerizing resin(Kooliner). Measurements of transverse strength were taken for each specimen. Specimens made of heat-cured resins, sizing $65\times10\times1.5mm$, were relined with heat-cured, light-cured, and autopolymerizing resin, respectively. Specimens relined with autopolymerizing and light-cured resins were further classified into not-contaminated, water-contaminated and saliva-contaminated groups. Again, measurements of the transverse strength were taken for each group. The results were as follows 1. The transverse strength of heat-cured resin was superior to all the other resins. 2. The transverse strength of each specimen decreased after relining in the following order, heat-cured, visible light-cured, and autopolymerizing resin. 3. Surface contamination produced an decrease in transverse strength, especially in the saliva contaminated group. According to these results, water or saliva contamination should be avoided during intraoral relining procedures.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.1
• /
• pp.64-73
• /
• 2010

This study was conducted to modify the surface properties of papers by formation of hydrophobic self-assembled monolayer(SAM) on paper surface with silanes. A base paper I(0.5% AKD) and base paper II(1.0-1.5% AKD) were reacted with silanes(PFDTES, DMDCS, MODDCS) by immersion method and vapor deposition method. Hydrophobic SAMs(contact angle value>$120^{\circ}C$) were obtained on all papers after treatment with $10^{\mu}l$ PFDTES for 15min, with $50^{\mu}l$ DMDCS for 30min, with $50^{\mu}l$ MODDCS for 300min. When applying PFDTES to paper surface, lower silane concentration and shorter reaction time were required, whereas MODDCS with long alkyl chain required the longest reaction time of 300min. The st$\ddot{o}$ckight sizing degree of silane treated papers were increased between 105sec(base paper I) and 130sec(base paper II). The wet tensile strength of PFDTES-treated base papers(I, II) increased by 10-34% after SAM formation. However, the wet tensile strength of the DMDCS-treated base paper(I) was found to decrease from 0.067kN/m to 0.038kN/m; this may due to the cellulose degrading as a result of generated hydrogen chloride when hydroxyl group of cellulose were reacted with DMDCS. No apparent changes of PPS roughness on silane-treated papers are observed. The ATR-IR spectrum showed absorption peak located at 465 and 1200cm-1 which can be assigned to the Si-O-C asymmetric stretching and Si-O-C bonds, respectively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.3
• /
• pp.254-259
• /
• 2014

A pressurized heavy water reactor (PHWR) core has 380 fuel channels contained and supported by a horizontal cylindrical vessel known as the calandria, whereas a pressurized water reactor (PWR) has only a single reactor vessel. The pressure tube, which is a pressure-retaining component, has a 103.4 mm inside diameter ${\times}$ 4.19 mm wall thickness, and is 6.36 m long, made of a zirconium alloy (Zr-2.5 wt% Nb). This provides support for the fuel while transporting the $D_2O$ heat-transfer fluid. The simple tubular geometry invites highly automated inspection, and good approach for all inspection. Similar to all nuclear heat-transfer pressure boundaries, the PHWR pressure tube requires a rigorous, periodic inspection to assess the reactor integrity in accordance with the Korea Nuclear Safety Committee law. Volumetric-based nondestructive evaluation (NDE) techniques utilizing ultrasonic and eddy current testing have been adopted for use in the periodic inspection of the fuel channel. The eddy current testing, as a supplemental NDE method to ultrasonic testing, is used to confirm the flaws primarily detected through ultrasonic testing, however, eddy current testing offers a significant advantage in that its ability to detect surface flaws is superior to that of ultrasonic testing. In this paper, effectiveness of flaw detection and the depth sizing capability by eddy current testing for the inside surface of a pressure tube, will be introduced. As a result of this examination, the ET technique is found to be useful only as a detection technique for defects because it can detect fine defects on the surface with high resolution. However, the ET technique is not recommended for use as a depth sizing method because it has a large degree of error for depth sizing.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.4
• /
• pp.1-10
• /
• 2014

In papermaking industry, inorganic fillers are widely used for the purpose of improving opacity, brightness, printability, uniformity and dimensional stability. They are also useful for production costs and energy savings. In the past, inorganic fillers in papermaking industry only focused on micro-scale but recently, new trials on nano-powdered technology are applying. Even nano-powdered fillers are rapidly utilized for improving the optical and surface properties in coating and surface sizing, there still have some problems in wet-end process due to poor dispersibility and retention. In this study, nano-particled calcium carbonate was produced by milling the PCC and its applicability between micro sized and nano sized calcium carbonated was compared in wet-end process, and finally the sheet properties were evaluated. Nano-PCC was not retained in sheet structure without applying retention system, but with retention system nano-powdered PCC was absorbed on fiber surface with expanding the fiber networks. The application of PAM-bentonite system has resulted in high ash retention and bulky structure for copier paper, and good optical properties in brightness and opacity. However, it required to solve the weakness of low tensile property due to interruption of hydrogen bonding by nano fillers.

• Journal of Convergence for Information Technology
• /
• v.10 no.7
• /
• pp.138-146
• /
• 2020

The paper deals with comparative study of characteristics of surrogate models and sensitivity evaluation using design of experiments in order to enhance and analysis the structure design of an automatic salt collector under various design load conditions. Orthogonal array design based on numerical analysis was used for the design of experiments. The thickness sizing variables of main structure member were considered the design factors, and the output responses were selected from the strength performances as well as the weight. The quantitative effects on responses for each design factor were evaluated from the orthogonal array experiment. Optimum design case was also identified to improve the strength performances with weight minimization. Using the orthogonal array experiment. various surrogate models such as response surface model, Kriging model, and Chebyshev orthogonal polynomial were generated. The orthogonal array experiment results were validated by the surrogate modeling results. The most suitable surrogate model was the response surface model for the exploration of design space of the automatic salt collector.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.187-191
• /
• 2006

Sputter deposition followed by surface treatment was studied using reactive RF plasma as a method for preparing titanium oxide $(TiO_2)$ films on the FTO $(SnO_2: F)$ substrate for dye-sensitized solar cells (DSCs). Anatase structure $TiO_2$ films deposited by reactive RF magnetron sputtering under the conditions of $Ar/O_2(5%)$ mixtures, RF power of 600W and substrate temperature of $400^{\circ}C$ were surface-treated by inductive coupled plasma (ICP) with $Ar/O_2$ mixtures at substrate temperature of $400^{\circ}C$, and thus the films were applied to the DSCs. We have chosen a solar cell width as a variable of a large-scaled DSCs and confirmed electric characteristics of an individual cell. As a result, the higher the internal resistance of DSC becomes, the wider the width gets. Internal resistance makes it difficult to collect photoelectron generated from dye. Ultimately up sizing DSC causes the increase of internal resistance and then has a bad effect on the cell characteristics.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.5
• /
• pp.526-531
• /
• 2001

The flow of remote field eddy current energy is studied at nonmagnetic coaxial tubes by using both experiments and finite element calculations based on commercial software package. The results showed that remote field eddy current energy at coaxial tubes flow along over the outer surface of external tube, not through the gap between internal and external tubes. This means that the through wall transmission characteristic of remote field eddy current testing (RFECT) is still valid at tube in tube configurations and the RFECT could be potential nondestructive technique for crack detection, spacer location and gap sizing at the coaxial CANDU fuel channel tubes.

• Journal of Ocean Engineering and Technology
• /
• v.34 no.4
• /
• pp.253-262
• /
• 2020

This study provides a comparative analysis of experiments-based enhancements and sensitivity evaluations for the structural design of an automatic ocean salt collector under various load conditions. The sizing variables of the structural members were considered as design factors. The strength and weight performances were selected as output responses. The design of experiments used in the comparative study consisted of the orthogonal array design, Box-Behnken design, and central composite design. The response surface model, one of the metamodels, was applied to the approximate model generation. The design enhancement performance metrics, including numerical costs and weight minimization, according to the design of experiments, were compared from the best design case results. The central composite design method showed the most enhanced design results for the structural design of the automatic ocean salt collector.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06b
• /
• pp.475-478
• /
• 2006

Environment-friendly shock-absorbing materials were made using a vacuum forming method from waste wood collected from local mountains in Korea. The waste wood was pulped by thermomechanical pulping. The TMP cushions showed superior shock-absorbing properties with lower elastic moduli compared to EPS and pulp mold. Even though the TMP cushions made using different suction times had many free voids in their inner fiber structure, their apparent densities were a little higher than EPS and much lower than pulp mold. The addition of cationic starch improved the elastic modulus of the TMP cushions without increasing the apparent density, which was different from surface sizing with starch. The porosity of the TMP cushions was a little greater than EPS and much less than pulp mold. Finally, the TMP cushions have great potential to endure external impacts occurring during goods distribution.