• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.279-289
• /
• 2000

Residual stress induced in U-bending and tube-to-tubesheet joint processes of PWR's row-1 heat exchanger tube was measured by X-ray method and Hole-Drilling Method(HDM). Compressive residual stresses(-) at the extrados surface were induced in U-bending, and its maximum value reached -319 MPa in axial direction at the position of $\psi$ = $0^{\circ}$. Tensile residual stresses(+) of $\sigma_{zz}$ = 45 MPa and $\sigma_{\theta\theta}$ = 25 MPa were introduced in the intrados surface at the position of $\psi$ = $0^{\circ}$. Maximum tensile residual stress of 170 MPa was measured at the flank side at the position of $\psi$ = $90^{\circ}$, i.e., at apex region. It was observed that higher stress gradient was generated at the irregular transition regions (ITR). The trend of residual stress induced by U bending process of the tubes was found to be related with the change of ovality. The residual stress induced by the explosive joint method was found to be lower than that by the mechanical roll method. The gradient of residual stress along the expanded tube was highest at the transition region (TR), and the residual stress in circumferential direction was found to be higher than the residual stress in axial direction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.61-66
• /
• 2008

This study is performed to compare characteristics of various measurement technique for weld residual stress. AISI 304 plate with one path weld on the surface was manufactured for this study. Hole drilling method, X-ray diffraction method and instrumented indentation method were used to measure the residual stress before and after welding. All the results were compared and analyzed.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.484-490
• /
• 2021

Instrumented indentation testing has been widely used for residual stress measurement. The Knoop indentation is mainly selected for determining anisotropic mechanical properties and non-equibiaxial residual stress. However, the measurement of equibiaxial stress state and compressive residual stress on a specimen surface using Knoop indentation is neither fully comprehended nor unavailable. In this study, we investigated stress conversion factors for measuring Knoop indentation on equibiaxial stress state through indentation depth using finite element analysis. Knoop indentation was conducted for specimens to determine tensile and compressive equibiaxial residual stress. Both were found to be increased proportionally according to indentation depth. The stress field beneath the indenter during each indentation test was also analyzed. Compressive residual stress suppressed the in-plane expansion of stress field during indentation. In contrast, stress fields beneath the indenter developed diagonally downward for tensile residual stress. Furthermore, differences between trends of stress fields at long and short axes of Knoop indenter were observed due to difference in indenting angles and the projected area of plastic zone that was exposed to residual stress.

• 한국정밀공학회지
• /
• 제20권9호
• /
• pp.135-141
• /
• 2003

MEMS structures generally have been fabricated using surface-machining method, but the interface failure between silicon substrate and evaporated thin film frequently takes place due to the residual stress inducing by the applied the various loads. And the very important physical property in the heated environment is the linear coefficient of thermal expansion. Therefore this paper studied the residual stress caused the thermal loads in the thin film and introduced the simple method to measure the trend of the residual stress by the indentation. Specimens were made of materials such as Al, Au and Cu and thermal load was applied repeatedly. The residual stress was measured by nano-indentation using AFM and FEA. The existence of the residual stress due to thermal load was verified by the experimental results. The indentation length of the thermal loaded specimens increased minimum 11.8％ comparing with the virgin thin film caused by tensile residual stress. The finite element analysis results are similar to indentation test.

• 한국안전학회지
• /
• 제17권1호
• /
• pp.18-24
• /
• 2002

This study verified the relationship between fracture mechanics parameters(${\Delta}K,\;K_{max}$) and X-ray parameters ($(\sigma}_r,;B$) for G365 steel at elevated temperature up to $300{\circ}C$. The fatigue crack propagation test were carried out and X-ray diffraction technique according to crack length direction was applied to fatigue fractured surface. The residual stress on the fracture surface was found to increase in low ${\Delta}K$ region, reach to a maximum value at a certain value of $K_{max}$ or ${\Delta}K$ and then decrease. Residual stress was independent on stress ratio by arrangement of ${\Delta}K$ and half value breadth was independent by the arrangement of $K_{max}$. The equation of ${\sigma}_r-{\Delta}K$ was established by the experimental data. Therefore, fracture mechanics parameters could be estimated by the measurement of X-ray parameters.

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.201-206
• /
• 2001

The hole-drilling method makes a little hole through the metal surface that has residual stress and measures the relieved stress with a strain gage. It is used widely in measuring the residual stress of surfaces. In this method, the inclined hole is one of the source of error. This paper presents a finite element analysis of influence of the inclined hole for the uniaxial residual stress field. The stress differences between measured and applied residual stress increase proportionally to inclined angle of the hole. The correction equations which easily obtain the residual stress taking account of the inclined angle and direction are derived. The measurement error of stress due to the inclined hole can be reduced to around 1% through this study.

• 한국강구조학회 논문집
• /
• 제13권4호
• /
• pp.327-335
• /
• 2001

강관 적층용접부에서 발생하는 잔류응력의 특징과 생성 메커니즘을 밝히기 위해 유한요소법을 이용한 3차원 열탄소성 해석을 수행하였다. 용접에 의해 강관을 접합할 때, 원주방향잔류응력과 두께방향잔류응력은 강관 내 외부에서 모두 접합부에서 인장응력이 발생하고, 길이방향잔류응력은 강관 내무에서 인장응력, 외부에서 압축응력이 발생된다. 또한 강관 적층 용접부의 잔류응력 생성기구를 명확히 하였다. 그 결과, 강관의 용접에 의한 잔류응력은 열응력에 의해 발생 할 뿐만 아니라, 강관의 기하학적 형상변화에 의한 영향도 받는다는 것을 밝혔다. 그리고, 용접조건과 강관의 제원이 달라질 경우에도 잔류응력 생성기구가 변함이 없음을 밝혔다.

• 소성∙가공
• /
• 제21권3호
• /
• pp.172-178
• /
• 2012

We performed a shot peening test and used a 2-D finite element model which predicts the compressive residual stress distribution below the material's surface. In this study, the concept of 'impact cycle' is introduced to account for the irregularity in the shot's impact position during testing. The impact cycle was imbedded in the finite element model. In the shot peening test, shot bombarded a type-A Almen strip surface with different impact velocities. To verify the proposed finite element model, we compared the deformed cross sectional shape of the Almen strips with the shapes computed by the proposed finite element model. Good agreement was noted between measurements and the finite element model predictions. With the verified finite element model, a series of finite element simulations was conducted to compute the residual stress distribution below the material's surface and the characteristics of these distributions are discussed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.418-422
• /
• 2005

In this study, the die design and die series on the surface residual stress of cold drawn eutectoid steel wire has been investigated. Test pieces were fabricated using die series with different mean and final reduction ratio. Surface residual stresses in the axial direction were measured by X-ray diffraction, Broker's 2-dimensional GADDS system. Results were compared with stress profiles which were calculated by 3D and 2D finite element simulation, Hibbitt's ABAQUS 6.4 program in Finite Element Analysis. By means of FEA method, optimal die shape considering delta-parameter were induced and applied in order to determine die sequence designs. Balance of the drawing stresses was also introduced to optimize die sequence.

• 소성∙가공
• /
• 제15권2호
• /
• pp.153-157
• /
• 2006

In this study, the die design and die series on the surface residual stress of cold drawn eutectoid steel wire have been investigated. Test pieces were fabricated using die series with different mean and final reduction ratios. Surface residual stresses in the axial direction were measured by X-ray diffraction, Bruker's 2-dimensional GADDS system. The results were compared with stress profiles that were calculated by 3D and 2D finite element simulations, ABAQUS 6.4 program in finite element analysis(FEA). By means of the FEA method, optimal die shape considering delta-parameter were induced and applied in order to determine die sequence designs. Balance of the drawing stresses was also introduced to optimize die sequence.