• Korean Journal of Agricultural and Forest Meteorology
• /
• v.23 no.4
• /
• pp.283-294
• /
• 2021

Solar radiation is an important meteorological factor in the agricultural sector. The ground exposed to sunlight is highly influenced by the surrounding terrains especially in South Korea where the topology is complex. The solar radiation on an inclined surface is estimated using a solar irradiance correction factor for the slope of the terrain along with the solar radiation on a horizontal surface. However, such an estimation method assumes that there is no barrier in surroundings, which blocks sunlight from the sky. This would result in errors in estimation of solar radiation because the effect of shading caused by the surrounding terrain has not been taken into account sufficiently. In this study, the shading effect was simulated to obtain the brightness value (BV), which was used as a correction factor. The shaded relief images, which were generated using a 30m-resolution digital elevation model (DEM), were used to derive the BVs. These images were also prepared using the position of the sun and the relief of the terrain as inputs. The gridded data where the variation of direct solar radiation was quantified as brightness were obtained. The value of cells in the gridded data ranged from 0 (the darkest value) to 255 (the brightest value). The BV analysis was performed using meteorological observation data at 22 stations installed in study area. The observed insolation was compared with the BV of each point under clear and cloudless condition. It was found that brightness values were significantly correlated with the solar radiation, which confirmed that shading due to terrain could explain the variation in direct solar radiation. Further studies are needed to accurately estimate detailed solar radiation using shaded relief images and brightness values.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.254-261
• /
• 2000

Soil chemical properties, relief of field surface, SPAD values and grain yield were investigated in a 0.5ha paddy field in 1999 to obtain basic field information for precision agriculture. Descriptive statistics of field information showed that the coefficient of variation ranged from 1.63% to 38.7%. Field information showed a high spatial dependence for within paddy field. The ranges of spatial dependence were from 15m to 60m, respectively. Kriged maps enable the visualization and comparison the spatial variability of field information. The causes of spatial variability of the field information could be explained rationally by a field management map. Grain yield was negatively correlated with pH, relief values, whereas, was positively correlated with total C, total N, C/N ratio, mineralizable N, available P and exchangeable K, Ca at the significant level of 1 %.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.66-66
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.07a
• /
• pp.299-300
• /
• 2007

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.02a
• /
• pp.339-340
• /
• 2006

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.07a
• /
• pp.245-246
• /
• 2008

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.309-312
• /
• 2004

In mountainous area with high relief, topography may cause cast shadows due to the blocking of direct solar radiation. Remote sensing images of these landscapes display reduced values of reflectance for shadowed areas compared to non-shadowed areas with similar surface cover characteristics. A variety of approaches are possible, though a common step in various active approaches is first to delineate the shadows using automated algorithm and digital surface model (or digital elevation model). This articles demonstrates a common confusion caused by cast shadows

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.114-118
• /
• 1996

Evaluation of cutting condition is one of the most important aspect to improve productivity and quality. In this study, the wear and cutting characteristics(cutting force, acoustic emission signal and surface roughness) of ceramic cutting tool for hardened die material(SKD11) were investigated by experiment. Flank wear on relief face of tool was occurred more dominant than crater wear on rake face. Experiments were performed under the various cutting condition.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1087-1090
• /
• 2008

Present research is devoted to the development of optical sheet intended to be used inside LCD Backlight unit in order to improve output axial Luminance. It deals with refractive by nature optical sheet having relief embossed top surface (microlenses array). Patterned reflecting layer can be coated on flat bottom surface.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1520-1530
• /
• 1997

Machining pressed compacts of ceramic and WC-Co materials can be the most cost effective way of forming the bodies prior to sintering when the required number of pieces is small. In this study, in order to clarify the machinability for turning, the $Si_3N_4$ and the WC-Co green compacts unsintered were machined under different cutting conditions with various tools. Absorbing chips by vacuum hose decreases tool wear. The tool wear becomes larger in the order of the ceramic, CBN and cemented carbide tools in machining the $Si_3N_4$ green compacts. In machining the WC-Co green compacts, the tool wear becomes larger in the order of the ceramic, cemented carbide and CBN tools. The land of cutting edge does not affect tool wear. When machining with cemented carbide tool, the tool wear i equal cutting length is nearly identical in spite of the increase of cutting spee, and the roughness of machined surface was the best in the cutting speed of 90 m/min. The tool wear decreases with the increase of rake angle and relief angle and with the decrease of nose radius. The machined surfaces become worse with the increase of feed rate and depth of cut, and with the decrease of rake angle and relief angle. The tool wear is not affected by the feed and depth of cut.