• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.144-150
• /
• 2011

The effect of low profile agent and release agent on the surface and mechanical properties of bulk mold compound were investigated. Atomic content and contact angle of surface were characterized using X-ray photoelectron spectroscopy and contact anglemeter. Surface morphology and surface roughness were obtained using field emission scanning electron microscope and atomic force microscope, respectively. As increasing the low profile agent from 0 to 9.2 wt%, the volume shrinkage and surface roughness decreased from 0.35% to 0.05%, and from $0.27{\mu}m$ to $0.12{\mu}m$, respectively. The increase of release agent from 1.8 wt% to 3.6 wt% resulted in the migration of release agent to sample surface and it increased the surface roughness. The flexural strength and impact strength were decreased approximately 30% as the low profile agent increasing from 5.0 wt% to 9.0 wt%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.128-141
• /
• 1994

This roport explain the basic theory of desinging the accelerating durability test road and the role of each factors contributing to test road surface profile. Also this road is designed by considering the charactors of vehicle suspension system and condition of driving. In test road, the factors affecting to the vehicle Structural durability are correlation among surface shape of road profile, frequency of vehicle suspension system, distribution of axletwist angle and vibration profile height Road PSD magnitude and frequency delay is used to control these factors relation.

• Journal of The Geomorphological Association of Korea
• /
• v.26 no.4
• /
• pp.21-31
• /
• 2019

Timing of terrace formation is a key information for understanding the evolution of fluvial systems. In particular, dating strath terrace (i.e. timing of terrace abandonment) is more difficult than depositional terrace that is conventionally constrained by radiocarbon, OSL and other dating methods targeting samples within terrace deposit. Surface exposure dating utilizing cosmogenic ¹⁰Be provides more reliability because it can be applied directly to the surface of a fluvial terrace. Thus, this method has been increasingly used for alluvial deposits. As well as other geomorphic surfaces over the last decades. Some inherent conditions, however, such as post-depositional ¹⁰Be concentration (i.e. inheritance), surface erosion rate, and density change challenge the application of cosmogenic ¹⁰Be to depositional terrace surface against simple bedrock surface. Here we present the first application of ¹⁰Be depth profile dating to a thin-gravel covered strath terrace in Korea. Monte Carlo simulation (MCS) helped us in better constraining the timing of abandonment of the strath terrace, since which its surface stochastically denuded with time, causing unexpected change of ¹⁰Be production with depth. The age of the strath terrace estimated by MCS was 109 ka, ~4% older than the one (104 ka) calculated by simple depth profile dating, which yielded the best-fit surface erosion rate of 2.1 mm/ka. Our study demonstrates that the application of ¹⁰Be depth profile dating of strath terrace using MCS is more robust and reliable because it considers post-depositional change of initial conditions such as erosion rate.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.3
• /
• pp.114-120
• /
• 1988

A water surface profile computation model using a standard step procedure was developed for gradually varied flow at an irrigation channel network. Flow characteristics ab Banweol district near Suweon were field monitored during irrigation periol of 1987. The model was applied to the main system at the district and the simulation results were compared to the field data. The results are sumrnarized as follows ; 1. The simulated water surface profiles from the model were in good agreement with the measured water surface profiles at different flow rates. 2. The model applicability for defining a stage-discharge relationship at a channel reach was demonstrated with reasonable accuracy when water stage and friction factor were given. 3. The roughness coefficient was found to be a major factor sigrificantly affecting computed water surface profile among a few physical input parameters for the model.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.42-47
• /
• 2001

The heat (mass) transfer characteristics on the blade surface of a first-stage turbine rotor cascade for power generation has been investigated by employing the naphthalene sublimation technique. A four-axis profile measurement system is successfully developed for the measurements of the local heat (mass) transfer coefficient on the curved blade surface. The experiment is carried out at the free-stream Reynolds number and turbulence intensity of $2.09\times10^5$ and 1.2%. The results on the blade surfaces show that the local heat (mass) transfer on the suction surface is strongly influenced by the endwall vortices, but that on the pressure surface shows a nearly two-dimensional nature. The pressure surface has a more uniform distribution of heat load than the suction one.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.613-617
• /
• 2000

This paper descries the effect of the stylus tip size on the measuring error in surface topography measurement. To analyze the distortional effect of an actual surface geometry originating from the finite stylus size, the surface is modeled as a sinusoid and the stylus tip as a circle. the measuring error is defined as the ratio of the standard deviation of a tracing profile and an original profile. It is shown that this measuring error depends on the amplitude and wavelength of an original profile. In this paper, the spectrum analysis is applied to investigate the distortional effect due to the mechanical filtering of the stylus in the frequency domain. and, the cumulative power spectrum is applied to determinate the minimum wavelength limits to be measured with the various stylus tip radius from these results, a new method to select proper stylus tip radius is proposed.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.9-12
• /
• 2006

A spectral analysis and numerical simulation are employed to assess the effects of the stylus tip radius on measuring surface profiles. Original profiles with fractal spectral densities are generated and then are numerically traced with circular tipped stylus. Instead of their spectral densities, the accumulative power spectrums of traced profiles are analyzed. It is shown that the minimum wavelength of traced profile relates directly to the radius r of the stylus tip and the root-mean-square (rms) roughness ${\sigma}_o$ of original profile. From this accumulation spectral analysis, a formula is developed to estimate the minimum wavelength of traced profile. By using the concept of the minimum wavelength, an appropriate stylus tip radius can be chosen for the given rms roughness ${\sigma}_o$ of the profile.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.04a
• /
• pp.61-62
• /
• 2007

low angle forward reflected neutral beam etching system으로 식각한 후 SIMS depth profile을 이용하여 에너지 침투 깊이에 따른 중성빔 에너지를 분석하여 중성화 과정에서 에너지와 flux의 손실이 있었다. 기존의 two-grid 대신에 three-grid를 사용하여 에너지의 변화없이 이온 flux 및 중성빔 flux가 향상됨을 알 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.781-782
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.573-574
• /
• 2010