• Journal of Magnetics
• /
• v.12 no.1
• /
• pp.27-30
• /
• 2007

Experimental evidence suggests that spin pinning conditions for standing spin mode in polycrystalline $Ni_{84}Fe_{16}$ alloy film, is confirmed using the four categories of Camley et al. and the value of q$\bot$ for the pinning conditions, this was achieved by performing Brillouin light scattering measurements. The value of q$\bot$ was observed, in order to increase at a rate of $\pi$/2 with an increasing mode number. With this condition, the coexistence of standing spin wave modes was shown, with intermediate pinning, in addition to free and strong pinning. The values for spin-wave-stiffness constant ($D_B$), g-factor (g), and surface magnetization (4$\pi$M) of the Permalloy film were obtained from the results of BLS, and determined to be $D_B=1.85{\pm}0.05Oecm^2$, $g=2.11{\pm}0.02$, and 4$\pi$M=8.7 kG, respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.22 no.2
• /
• pp.21-25
• /
• 2020

We investigated the flux pinning property of GdBa₂Cu₃O_7-x (GdBCO) films on top of La_0.7Sr_0.3MnO₃ (LSMO) nanoparticles deposited by a surface decoration. Both GdBCO films and LSMO nano particles were deposited by pulsed laser deposition and the number of laser pulses were varied from 80 to 320 in order to control the density of the LSMO nanoparticles. The magnetization data at 77 K showed that the critical current density (J_c) was enhanced in all of the GdBCO films with LSMO nanoparticles and that the J_c enhancement was found to be inversely proportional to the LSMO nanoparticle density. Structural analyses revealed that LSMO nanoparticles induce a compressive strain in the GdBCO films resulting in a disordering in the CuO₂ plane. Therefore, the enhanced flux pinning property in the GdBCO with LSMO nanoparticles was attributed to the competing effect between the increase of pinning centers and the increase of compressive strain in the superconducting phase.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.15-18
• /
• 2008

To achieve high transport current without degradation under magnetic field, it is essential to artificially generate the pinning sites at which moving magnetic flux can be pinned. In this work, $ZrO_2$ nanodots were formed on the substrate surface using electro-spray deposition method. On top of the nanodots, the extended and effective pinning centers can be created. The positively charged Zr precursor solution was sprayed out from the needle using the corona discharge phenomena. Then, the sprayed precursor was deposited onto the negatively charged substrate surface followed by the heat treatment under the controlled atmosphere. Using the electrostatic force among the charged particles of precursor, evenly distributed and nano-sized dots were formed on the substrate surface. The size and density of the nanodots were studied by Atomic Force Microscopy. Also discussed are the effect of the deposition time and solution concentration on the size and density of the nanodot and processing variables in electro-spray method for the effective flux pinning centers in the superconducting films.

• Applied Microscopy
• /
• v.43 no.2
• /
• pp.88-97
• /
• 2013

Technical investigation to figure out the problems arising during in-situ heating electron backscatter diffraction (EBSD) analysis inside scanning electron microscopy (SEM) was carried out. EBSD patterns were successfully acquired up to $830^{\circ}C$ without degradation of EBSD pattern quality in steels. Several technical problems such as image drift and surface microstructure pinning were taking place during in-situ experiments. Image drift problem was successfully prevented in constant current supplying mode. It was revealed that the surface pinning problem was resulted from the $TiO_2$ oxide particle formation during heating inside SEM chamber. Surface pinning phenomenon was fairly reduced by additional platinum and carbon multi-layer coating before in-situ heating experiment, furthermore was perfectly prevented by improvement of vacuum level of SEM chamber via leakage control. Plane view in-situ observation provides better understanding on the overall feature of recrystallization phenomena and cross sectional in-situ observation provides clearer understanding on the recrystallization mechanism.

• Progress in Superconductivity
• /
• v.11 no.1
• /
• pp.62-66
• /
• 2009

Introduction of proper impurity into $YBa_2Cu_3O_{7-x}$ (YBCO) thin films is an effective way to enhance its flux-pinning properties. We investigate effect of $Y_2O_3$ nanoparticles on the critical current density $J_c$ of the YBCO thin films. The $Y_2O_3$ nanoparticles were created perpendicular to the film surface (parallel with the c-axis) either between YBCO and substrate or on top of YBCO, YBCO/$Y_2O_3$/LAO or $Y_2O_3$/YBCO/STO, by pulsed laser deposition. The deposition temperature of the YBCO films were varied ($780^{\circ}C$ and $800^{\circ}C$) to modify surface morphology of the YBCO films. Surface morphology characterization revealed that the lower deposition temperature of $780^{\circ}C$ created nano-sized holes on the YBCO film surface which may behave as intrinsic pinning centers, while the higher deposition temperature produced much denser and smoother surface. $J_c$ values of the YBCO films with $Y_2O_3$ particles were either remained nearly the same or decreased for the samples in which YBCO is grown at $780^{\circ}C$. On the other hand, $J_c$ values were enhanced for the samples in which YBCO is grown at higher temperature of $800^{\circ}C$. The difference in the effect of $Y_2O_3$ can be explained by the fact that the higher deposition temperature of $800^{\circ}C$ reduces intrinsic pinning centers and $J_c$ is enhanced by introduction of artificial pinning centers in the form of $Y_2O_3$ nanoparticles.

• Journal of Magnetics
• /
• v.10 no.4
• /
• pp.157-162
• /
• 2005

We report the magnetic-field dependence of the irreversible magnetization of binary superconductor $MgB_2$. For the temperature region of $T\;<\;0.9T_c$, the contribution of the bulk pinning to the magnetization overwhelms that of the surface pinning. This was evident from the fact that the magnetization curves, M(H), were well described by the critical-state model without considering the reversible magnetization and the surface pinning effect. It was also found that the M(H) curves at various temperatures scaled when the field and the magnetization were normalized by the characteristic caling factors H$\ast$(T) and M$\ast$(T), respectively. This feature suggests that the pinning mechanism determining the hysteresis in M(H) is unique below $T\;=\;T_c$.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.613-618
• /
• 2013

In this paper a new concept on z-pinning technology named by authors as 'z-pinning patch' will be introduced, which advantage is easy application at manufacturing site of composite structures. Using the trial manufactured z-pinning patch, the z-pinned composite single-lap shear joint specimens were successfully manufactured and tested to check the improvement of joint strengths. The z-pin's material is stainless steel and its surface was machined as zagged shape and chemically corroded to improve joint force with composite materials.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.188-192
• /
• 2002

To introduce flux pinning center in HTS-BSCCO system, nano-size MgO particles were uniformly distributed within the Bi-2223 grain by partial hydration of MgO. The existing method MgO doped Bi-2223 used nato-size MgO powders, which resulted in agglomeration during mixing or grain growth during heat-treatment due to the high surface energy of the fine particles. By hydration of the MgO surface, the agglomeration of the MgO powders was avoided and the size of remaining MgO core was controlled by changing hydration medium and time. The thin film obtained by spin coating of (Bi_$1.8/Pb_{0.4}$)$Sr_2$$_{Ca}$$2.2/Cu_3$ $O_{y}$ nitrate solution mixed with hydrated MgO showed the even distribution of nano-size MgO particles in the Bi-2212 grains.s.s.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.375-375
• /
• 2009

For many large-scale applications of high-temperature superconducting materials, large critical current density($J_c$) in high applied magnetic fields are required. A number of methods have been reported to introduce artificial pinning centers(APCs) in $YBa_2Cu_3O_{7-\delta}$(YBCO) films for enhancement of their $J_c$. We report measurements of critical current in $YBa_2Cu_3O_{7-\delta}$ films deposited by PLD on $SrTiO_3$ substrates decorated with Au nanoparticles. Au nanoparticles were synthesized on STO substrates with self assembled monolayer. Microstructural analysis of the obtained YBCO films was performed by using cross-section transmission electron microscopy(TEM). Phase and textural analysis was done using X-ray diffraction. The surface morphology and surface roughness(Ra) of the layers was measured by atomic force microscopy(AFM).

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.90-96
• /
• 2011

We investigated the properties of artificial pinning centers of YBCO multilayer films in which $Y_2O_3$ and ZnO nanoparticles are uniformly introduced by using the pulsed laser deposition (PLD) technique. $Y_2O_3$ and ZnO nanoparticles were deposited on top of YBCO buffer layer and the density of nanoparticles was controlled by varying the number of nanoparticle layers. YBCO superconducting layers with total thickness of 250 nm were deposited on top of $Y_2O_3$ and ZnO nanoparticles. Based on analyses of the surface morphology, the transition temperature $T_c$, and the critical current density $J_c$, we discussed the difference between the two kinds of nanoparticles as flux pinning centers.