• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.478-481
• /
• 2013

Diameter controlled carbon nanotubes (CNTs) were grown using surface modified iron nano-particle catalysts with aminpropyltriethoxysilane (APS). Iron nano-particles were synthesized by thermal decomposition of iron pentacarbonyl-oleic acid complex. Subsequently, APS modification was done using the iron nano-particles synthesized. Agglomeration of the iron nano-particles during the CNT growth process was effectively prevented by the surface modification of nano-particles with the APS. APS plays as a linker material between Fe nano-particles and $SiO_2$ substrate resulting in blocking the migration of nano-particles. APS also formed siliceous material covering the iron nano-particles that prevented the agglomeration of iron nano-particles at the early stages of the CNT growth. Therefore we could obtain the diameter controlled CNTs by blocking agglomeration of the iron nano-particles.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1771-1773
• /
• 2007

Surface modification of the gate dielectric has a strong influence on the performance of printed transistors. The surface modification occurs between the gate dielectric and semiconductor. The printed transistor with evaporated vanadium pentoxide ($V_2O_5$) modification exhibits a mobility of $0.2cm^2\;V^{-1}\;s{-1}$ and a subthreshold slope of 1.47 V/decade.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1319-1324
• /
• 1996

Silica aerogels were synthesis by the sol-gel-supercritical drying process using isopropanol as a solvent. Effets of the heat-treatment and the surface modification through propoxylation on the structural reinforcement as well as the surface hydrophobic/hydrophilic characteristics of aerogels were investigated. Silica aerogels synthesized by supercritical drying were hydrophobic but aerogels heat-treated above 20$0^{\circ}C$ were transformed to be hydrophilic. In particular it was found that the skeletal structure of aerogels heat-treated at 50$0^{\circ}C$ was strong enough not to crack after adsorbing a large amount of water vapor. Hydrophilic aerogels modified by propoxylation at 28$0^{\circ}C$ for 20 h were reversed to the hydrophobic form. Transition between hydrophobicity and hydrophilicity was reversible. The hydrophobicvity and the hydrophilicity of silica aerogels were attributed to the Si-Oh bond and the nonpolar C-H bond groups of orgainc species respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.91-94
• /
• 2009

We propose advanced liquid crystal display (LCD) modes through surface modification using UV curable reactive mesogen (RM) mixed with alignment layers. The LC directors on the modified alignment layer are controlled and memorized by the polymerized RMs under an applied voltage. Using the method proposed here, we can improve the response time and viewing angle characteristics through surface controlled patterned vertical alignment (SC-PVA) mode and 8-domains PVA mode, respectively. Also, we found that the method can be applicable to fabricate multi-domain structures using multiple UV exposure as same as conventional UV alignment method.

• Journal of the Korean Physical Society
• /
• v.73 no.12
• /
• pp.1867-1872
• /
• 2018

This study proposes a route for surface modification for p-type cobalt oxide-based gas sensors. We deposit a thin layer of Ni on the Co oxide film by sputtering process and annealed at $350^{\circ}C$ for 15 min in air, which changes a typical sputtered film surface into one interlaced with a high density of hemispherical nanoparticles. Our in-depth materials characterization using transmission electron microscopy discloses that the microstructure evolution is the result of an extensive inter-diffusion of Co and Ni, and that the nanoparticles are nickel oxide dissolving some Co. Sensor performance measurement unfolds that the surface modification results in a significant sensitivity enhancement, nearly 200% increase for toluene (at $250^{\circ}C$) and CO (at $200^{\circ}C$) gases in comparison with the undoped samples.

• Journal of Adhesion and Interface
• /
• v.23 no.3
• /
• pp.70-74
• /
• 2022

Tannic acid, one of plant-derived polyphenols, has been studied as a molecular adhesive, surface modification, energy storage and generating device, and biomedical application as it can interact with biopolymers. In this study, we synthesized porous silica nanoparticles that are widely used in biomedical engineering fields such as drug delivery and bioimaging, and then analyzed tannic acid mediated surface modification of mesoporous silica nanoparticles.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3805-3810
• /
• 2013

The surface modification of silica particles (SPs) was systemically conducted by the treatment of 0.1-10 wt % phenylsilanetriol (PST) on the basis of SPs used through two step processes: 1) the PST coating of SPs via evaporation under reduced pressure and 2) their thermal condensation leading to Si-O-Si bond formation via heating at $130^{\circ}C$. The evaluation of the modified SPs was conducted by the simple floating test on water and the measurement of the contact angle (CA) of water droplet on the 2-dimensional layer of modified SPs on slide glass. When PST was used about 2 wt % or above on the basis of SPs (about average size: 50 nm) used, the modified SPs were fully floated on the water and all dispersed into upper organic solvent layer after a shaking with the mixture of the water and benzene, indicating that the modified SPs have hydrophobic properties. The modified SPs were characterized by $^{29}Si$ MAS NMR and physicochemical properties including SEM, TEM, BET, adsorption/desorption isotherms, etc. were measured and compared each other in details. This research demonstrates that the organosilanetriol is a good modifier applicable for the surface modification of inorganic oxide particles using a low amount of modifier on the basis of oxide particles used.

• Journal of Welding and Joining
• /
• v.24 no.1
• /
• pp.43-49
• /
• 2006

This paper describes the friction surface modification which has been successfully developed with the friction stir welding recently There are several problems including just position control and backlash in conventional friction surface modification system. Therefore it has been developed the friction surface modification system which has been controlled precisely both position and force by driving hydraulic cylinder in this paper. The mechtrode rotation speed(N) and feeding speed(Vz), travel speed(Vx,y) are of critical importance for the width and thickness of the coating in friction surfacing process. But there is no theoretical method of determining interrelations between process parameters affect the coating width and thickness. As a result of DOE(design of experiment) with developed system, the coating thickness and width seemed to decrease according to increase the mechtrode rotation speed(N) and traveling speed(Vx,y), to decrease feeding speed(Vz) apparently. However as the result of regression analysis the main effect was only the mechtrode rotation speed in the coating thickness.

• Journal of Powder Materials
• /
• v.19 no.3
• /
• pp.177-181
• /
• 2012

Copper composite materials have attracted wide attention for energy applications. Especially $CuInS_2$ has a desirable direct band gap of 1.5 eV, which is well matched with the solar spectrum. $CuInS_2$ nanoparticles could make it possible to develop color-tunable $CuInS_2$ nanoparticle emitter in the near-infrared region (NIR) for energy application and bio imaging sensors. In this paper, $CuInS_2$ nanoparticles were successfully synthesized by thermo-decomposition methods. Surface modification of $CuInS_2$ nanoparticles were carried out with various semiconductor materials (CdS, ZnS) for enhanced optical properties. Surface modification and silica coating of hydrophobic nanoparticles could be dispersed in polar solvent for potential applications. Their optical properties were characterized by UV-vis spectroscopy and photoluminescence spectroscopy (PL). The structures of silica coated $CuInS_2$ were observed by transmission electron microscopy (TEM).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.130.1-130.1
• /
• 2013

We made attempts to improve photocatalytic activity of $TiO_2$ nanoparticles under visible light exposure by combining two additional treatments. N-doping of $TiO_2$ by ammonia gas treatment at $600^{\circ}C$ increased absorbance of visible light. By coating thin film of polydimethylsiloxane (PDMS), and subsequent vacuum-annealing at $800^{\circ}C$, $TiO_2$, became more hydrophilic, thereby enhancing photocatalytic activity of $TiO_2$. Four types of $TiO_2$ samples were prepared, bare-$TiO_2$, hydrophilic-modified $TiO_2$ ($h-PDMS/TiO_2$), N-doped $TiO_2$ ($N/TiO_2$) and hydrophilic-modified and N-doped $TiO_2$ ($h-PDMS/N/TiO_2$). Adsorption capability was evaluated under dark condition and photocatalytic activity of $TiO_2$ was evaluated by photodegradation of MB under blue LED (400 nm< ${\lambda}$) irradiation. N-doping on $TiO_2$ was characterized using XPS and hydrophilic modification of $TiO_2$ surface was analyzed by FT-IR spectrometer. It was found that N-doping and hydrophilic modification both had positive effect on enhancing adsorption capability and photocatalytic activity of $TiO_2$ at the same time. Particularly, N-doping enhanced visible light absorption of $TiO_2$, whereas hydrophilic surface modification increased MB adsorption capacity. By combining these two strategies, photocatalytic acitivity under visible light irradiation became the sum of individual effects of N-doping and hydrophilic modification.