• Journal of the Korean Society for Precision Engineering
• /
• v.9 no.1
• /
• pp.96-105
• /
• 1992

A study on the construction of a CAD/CAM system operated by 16 Bit PC basic language, for machining sculptured surface of die, was carried out. The system consists of 2 steps i.e., process for geometric modelling by wire frame and process for machining data generation. Geometric modelling for sculptured surface is made by the point data fitting, parallel sweeping, normal sweeping and linear connection of cross section curve. Machining data are gained by cutter off-set of geometric model data and machining carried out by DNC. This system is to be proved enough for rough cutting by actual machining experiment. But, for becoming a high level system, another method of cutter off-set has to be regarded and system must be reconstructed by another program language.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.82-88
• /
• 1997

In this paper, the development of a precision CNC lathe prototype for mirror surface machining is presented. To obtain high precision machining accuracy, a hydrostatically supported precision spindle and a sliding guideway with turcite pad are adopted as the motion elements. The machining accuracy of the prototype machine, and the motional accuracy of its motion elements are tested and evaluated to confirm the validity of the application of these elements on the prototype. The hydrostatic spindle shows 0.09 .mu. m of rotational accuracy and the guideway shows about 0.8 .mu. m/170mm of horizontal straightness. The sur- face roughness of cupper and aluminium cylinder machined by the prototype machine with diamond tool are 0.07 .mu. m and 0.10 .mu. m Rmax respectively. From these results, it is verified that the prototype lathe is avail- able for high precision machining.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.4 no.3
• /
• pp.5-12
• /
• 2005

In wire discharge machining which is using STD 11 as die materials, the major factors of machining speed are discharge voltage, discharge current, and discharge time. All of the three factors give the effect. Increasing of the discharge pulse time gets groove width wider and it relatively increases surface roughness and clearance. If no load voltage is decreased, surface roughness is good but it decreases machining speed. If on time is increased, machining speed will get faster and clearance and offset value also get bigger.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.220-228
• /
• 1999

The machining accuracy has been improved with the development of NC machine tools and cutting tools. However, it is difficult to obtain a high degree of accuracy when machining deep pocket with long end mill, since machining accuracy is mainly dependant on the stiffness of the cutting tool. To improve surface accuracy in machining deep pocket using end mill, the performance by down cut and up cut is compared theoretically and experimentally. To verify usefulness of up milling, various experiments were carried out. As a result, it is found that up milling produce more accurate surface than down milling in machining deep pocket. For effective application of up milling, various values in helix angle, number of teeth, radial depth of cut and axial depth of cut are applied in experiment.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.4
• /
• pp.28-35
• /
• 2014

A composite honeycomb core is widely used for lightweight aircraft materials. However, the composite honeycomb core coupled with metal-cutting machining processes does not make a very good match. This paper describes an experimental study of the shape-machining characteristics of a composite honeycomb core, in which a five-axis gantry machine is used. The experimental conditions of the offset allowance, tooling condition and feed rate were applied. The shape machining characteristics of a flat surface, a vertical surface, and a concave surface are evaluated by comparing the machining shape and burr characteristics.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.7
• /
• pp.963-970
• /
• 2010

This study makes an estimate of the laser-assisted machining (LAM) of an economically viable process for manufacturing precision silicon nitride ceramic parts using a high-power diode laser (HPDL). The surface is locally heated by an intense laser source prior to material removal, and the resulting softening and damage of the workpiece surface simplify the machining of the ceramics. The most important advantage of LAM is its ability to produce much better workpiece surface quality compared to conventional machining. Also important are its larger material removal rates and longer tool life. The cutting force and surface temperature were measured on-line using a pyrometer and a dynamometer, respectively. Tool wear, chips and the surface of the workpiece were measured using optical microscopy, and the surface and fractured cross-section of $Si_3N_4$ were measured by SEM. During the LAM process, the cutting force and tool wear were reduced and oxidation of the machined surface was increased according to the increase in the laser power. Moreover, the more the feed rate increased, the more the cutting force and tool wear increased.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.7-11
• /
• 2014

The experimental analysis presented aims at the selection of the most optimal machining parameter combination for wire electrical discharge machining (WEDM) of STD11. Based on the Taguchi experimental design ($L_{27}$ orthogonal array) method, a series of experiments were performed by considering time-on, voltage, time-off, wire speed, and flow rate as input parameters. The surface roughness was considered responses. Based on the signal-to-noise (S/N) ratio, the influence of the input parameters on the responses was determined. The optimal machining parameters setting for the minimum surface roughness was found using Taguchi methodology. In order to investigate the effects of process parameters on the surface machined by WEDM, Several experiments are conducted to consider effects of time-on, voltage, time-off, wire speed and flow rate on the surface roughness. Analysis of variance (ANOVA) as well as regression analysis are performed on experimental data. The best results of surface roughness were obtained at higher voltage, lower wire speed, and lower time-on.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.45 no.4
• /
• pp.61-69
• /
• 2022

The function of coolant in machining is to reduce the frictional force in the contact area in between the tool and the material, and to increase the precision by cooling the work-piece and the tool, to make the machining surface uniform, and to extend the tool life. However, cutting oil is harmful to the human body because it uses chlorine-based extreme pressure additives to cause environmental pollutants. In this study, the effect of cutting temperature and surface roughness of titanium alloy for medical purpose (Ti-6Al-7Nb) in eco-friendly ADL slot shape machining was investigated using the response surface analysis method. As the design of the experiment, three levels of cutting speed, feed rate, and depth of cut were designed and the experiment was conducted using the central composite planning method. The regression expressions of cutting temperature and surface roughness were respectively obtained as quadratic functions to obtain the minimum value and optimal cutting conditions. The values from this formula and the experimental values were compared. As a result, this study makes and establishes the basis to prevent environmental pollution caused by the use of coolant and to replace it with ADL (Aerosol Dry Lubricant) machining that uses a very small amount of vegetable oil with high pressure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1483-1495
• /
• 1994

A quantitative analysis of a surface roughness for a precision machining of a sculptured surface in milling process is treated under superposition theory in this paper. The geometrical surface rouhgness is calculated as a function of feed per tooth, path interval, radii of tool and cutting edge, and radii of curvatures of workiece. Through machining experiments in a 3-axis machining center, we confirmed the adequacy of the adequacy of the analysis. While cutter mark is neglegible in ball endmilling, it is significant in flat endmilling. When feed per tooth is very small, flat endmilling gives superior finish to ball endmilling. In flat endmilling, cutting condition and cutter path should be strategically chosen to balance the cutter mark height and cusp height.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.3
• /
• pp.71-76
• /
• 2020

Various machining methods are being studied to improve the processing quality of the spherical R shape in press die. In this paper, we confirmed that changes in machining quality were associated with changes in cutting direction, path, and cutting angle, which are commonly used in the machining of molds. We obtained a surface roughness graph with each condition change in one specimen using an instrument that measured geometry and surface roughness simultaneously. The results of the study showed that the best surface roughness in the finish cut of the spherical surface was obtained using upward pick feed machining.