• Land and Housing Review
• /
• v.2 no.2
• /
• pp.163-170
• /
• 2011

Individual Vacuum Pressure Method (IVPM) is a soft ground improvement technique, in which a vacuum pressure can be directly applied to the vertical drain board to promote consolidation and to strengthen the soft ground. This method does not require surcharge loads, different to embankment or pre-loading method. In this study, the ground improvement efficiency of Individual Vacuum Pressure Method was estimated when suction pressure increases step by step(-20, -40, -60, -80kPa) with different periods. During Individual Vacuum Pressure Method process, surface settlement and pore pressure were monitored, and cone resistance as well as water content were also measured after the completion of Individual Vacuum Pressure Method treatment. From the results, optimum duration of each step of vacuum pressure was determined, and the settlement was calculated using FEM numerical analysis.

• Korean Journal of Environmental Agriculture
• /
• v.17 no.2
• /
• pp.160-163
• /
• 1998

In this study, the compostable household wastes from a house were composted in a home composter without adding any bulking agent and microorganisms. Every day wastes of 1kg were added to the composter during the experimental period. The following results were obtained : 1. Each component of the compostable household wastes generated every day showed very difference. 2. While composting proceeded at room temperature by suppling 1,1322 l air per hour, the composting material maintained the water content of 74.36 ${\sim}$ 85.14%, whereas while composting proceeded at $45^{\circ}C$ by suppling 427 l air per hour, the compost had optimal water content. The electric power of 132kwh a month was required by operating the composting unit at $45^{\circ}C$. 3. During 20 day, decomposition of 28% at room temperature and 44% at $45^{\circ}C$ were obtained respectively. 4. The accumulation of inorganic compound contents were not shown during the composting period, However, the content of salt and Cd was very high. Therefore, using the compost for agriculture has to be careful. 5. The biofilter removed the odorous substants efficiently at the room temperature due to increasing surface loading.

• Applied Chemistry for Engineering
• /
• v.19 no.2
• /
• pp.161-167
• /
• 2008

Multi-walled carbon nanotubes (MWCNT)-reinforced poly(ethylene-co-ethyl acrylate) (EEA) nanocomposites were prepared by both melt and solution mixing methods. The mechanical, thermal, and electrical properties were investigated as a function of type and loading of CNT. The tensile strength and modulus increased, while elongation at break decreased with increasing MWCNT content. The hollow-type MWCNT showed an improved tensile strength and elongation at break compared with a conventional MWCNT. The thermal degradation temperature was increased by around $40^{\circ}C$ with increasing the amount of MWCNT. The melt-mixed composites showed the highest volume resistivity. In the case of solution-mixed composites, the conventional MWCNT was estimated to show much lower volume resistivity than that of hollow MWCNT. The number and length of extruded CNT onto the fractured surface increased by both increasing the content of CNT and employing the tensile strain to the sample. The melt-mixed specimens showed much smaller number and shorter length of extruded CNT.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.5
• /
• pp.112-120
• /
• 2012

A numerical model considering the internal vaporization and the creep effect, in the form of a analytical program, for tracing the behavior of high strength concrete(HSC) members exposed to fire is presented. The two stages, i.e., spalling procedure and fire resistance time, associated with the thermal, moisture flow, creep and structural analysis, for the prediction of fire resistance behavior are explained. The use of the analytical program for tracing the response of HSC member from the initial pre-loading stage to collapse, due to fire, is demonstrated. Moisture evaporates, when concrete is exposed to fire, not only at concrete surface but also at inside the concrete to adjust the equilibrium and transfer properties of moisture. Finite element method is employed to facilitate the moisture diffusion analysis for any position of member, so that the prediction method of the moisture distribution inside the concrete members at fire is developed. The validity of the numerical model used in this program is established by comparing the predictions from this program with results from others fire resistance tests. The analytical program can be used to predict the fire resistance of HSC members for any value of the significant parameters, such as load, sectional dimensions, member length, and concrete strength.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.3
• /
• pp.186-194
• /
• 2011

The reinforced concrete beam-column connections are in lack of constructability and are likely to show anchorage failure because of the complex details of joint regions. Under seismic loads, a destruction of the column or the beam-column joint leads to collapse of the whole structures. For this reason, the safety of structures has to be guaranteed by following procedures which are based on the strong column-weak beam design concept: 1) failure of beam by generating plastic hinge in the beam maintained a certain distance from the surface of column, 2) failure of column or beam-column joint. In this study, headed bars were used as longitudinal reinforcements of beam and joint reinforcements in order to improve the strength and constructability of joint and to relocate plastic hinge. The finite element analyses (FEAs) were performed to the reinforced concrete beam-column joints utilizing headed bar reinforcements. To verify the availability of the analysis models, the FEAs for experimental tests performed by previous researchers were conducted and compared with the experimental results. Additional variables are also considered to confirm the excellence of headed bars. Analysis results indicate that the constructability of beam-column connections can be improved by using headed bars for the full anchorage of longitudinal reinforcements of beam under similar structural performance. In addition, the plastic hinge was relocated to the intended place by using headed bars as joint reinforcements. Under cyclic displacement loading, the energy dissipation capacity and ultimate stress were increased and the decrease in stiffness was minimized.

• Korean Journal of Ecology and Environment
• /
• v.37 no.2 s.107
• /
• pp.213-226
• /
• 2004

The present study was conducted to analyze the pattern of eutrophication of Korean reservoir with Chl. a concentration and morpho-physical parameters, and to valuate water quality characteristics of the classified types. The collected data from 486 reservoirs were classified as four types, with the Chl- a concentration (25 ${\mu}g\;L^{-1}$) and the ratio of water storage/surface area (mean depth, 7.5 m). According to OECD criteria and trophic state index based on Chl-a concentration, 34.3 and 72.8% of selected reservoirs appeared to be eutrophic, respectively. Characteristics of TYPE ll reservoirs generally showed high Chl-a concentration, relatively old age, small DA/LA ratio, short Hydraulic retention time, large paddy field and field to watershed ratio, and high pollutant loading compared to other types of reservoirs. The difference of TP concentration was greater than that of TN concentration in reservoir water among classified four types. Based on TN/TP ratio (by weight), phosphorus was limiting nutrient in all types and more closely related with Chl- a concentration than nitrogen. Significant decrease of Chl- a concentration with increase of TN/TP ratio observed only in reservoirs with Chl-a concentration > 25${\mu}g\;L^{-1}$. Although drainage area is believed to be a factor that is related to the generation load of pollutants in the watershed, it did not show any significant relationship with water quality parameters. Morphometric characteristics such as depth and age of reservoir as well as type of land use patterns in the watershed was among important parameters for the assessment of water quality characteristics in Korean reservoirs.

• Korean Chemical Engineering Research
• /
• v.58 no.1
• /
• pp.64-68
• /
• 2020

In this study, metal copper clad laminate can be prepared using epoxy composite filled with thermally conductive fillers. In order to improve the thermal conductivity of epoxy composites, it is important factor to form conductive networks through appropriate packing of conductive fillers in epoxy composite matrix and to decrease the amount of thermally resistant junctions involving a epoxy composite matrix layer between adjacent filler units. This is because epoxy has a thermal conductivity of only 0.2-0.3W, so in order to maintain high thermal conductivity, thermally conductive fillers are connected to each other, so that the gap between particles can be reduced to reduce thermal resistance. The purpose of this study is to find way to achieve highly thermally conductive in the epoxy composite matrix filled with Al₂O₃ and Boron Nitride(BN) filler by filler loading and uniform dispersion. As a results, the use of Al₂O₃/BN hybrid filler in epoxy matrix was found to be effective in increasing thermal conductivity of epoxy composite matrix due to the enhanced connectivity offered by more continuous thermally conductive pathways and uniform dispersion without interfacial voids in epoxy composite matrix. In addition, surface treatmented s-BN improves the filler dispersion and adhesion between the filler and the epoxy matrix, which can significantly decrease the interfacial thermal resistance and increase the thermal conductivity of epoxy composite matrix.

• Journal of Aquaculture
• /
• v.16 no.3
• /
• pp.142-150
• /
• 2003

Performance of a biological filter, the rotating biological contactor (RBC), is affected by rotational speed and hydraulic residence time (HRT). A RBC with a disc diameter of 62 cm, total surface area of 48.28 $m^2$, volume of 0.34 ㎥, and submergence ratio of 35.4% was tested for the combinations of five rotational speeds (1, 2, 3, 4 & 5 rpm) and three HRT (0.5, 1.0 & 2.0 hr) to find out the maximum removal efficiencies of total ammonia nitrogen (TAN) and nitrite nitrogen of a simulated recirculating aquaculture system. Ammonia loading rate in the system was 25 g of TAN/ ㎥. day. Removal efficiencies were checked when TAN concentrations in the system stabilized for 3 days in each treatment. The concentration of TAN in the system decreased with increasing rotational speed of the RBC up to 4 rpm in all HRT (P<0.05). At the rotational speed of 5 rpm, the efficiencies decreased in all HRT (P<0.05). When the rotational speeds were 1, 2, 3, 4, and 5 rpm, TAN concentrations in the system were 1.35, 0.94, 0.69, 0.66, and 0.76 mg/L at the 0.5 hr HRT, 2.86, 1.18, 0.96, 0.87, and 1.11 mg/L at the 1.0 hr HRT, and 5.30, 2.44, 1.99, 1.77, and 2.01 mg/L at the 2.0 hr HRT, respectively. The TAN removal efficiencies of the RBC at the rotational speeds of 1, 2, 3, 4, and 5 rpm were 32.9, 49.5, 65.1, 72.9, and 62.9% in 0.5 hr HRT,33.1, 74.1, 87.1, 95.8, and 78.5% in 1.0 hr HRT, and 35.5, 76.7, 89.6, 97.0, and 85.5% in 2.0 hr HRT, respectively. TAN removal efficiency of RBC per pass increased with increasing HRT. However, TAN concentration in the system also increased. The best operating condition among the treatments was obtained at the treatment of 0.5 hr HRT and 4 rpm (P<0.05). The TAN concentration was 0.66 mg/L. Concentrations of nitrite nitrogen (NO$_2$$^{[-10]}$ -N) in the system decreased with increasing rotational speed in all HRT while that in the system increased with increasing HRT in all rotational speeds. The ranges of NO$_2$$^{[-10]}$ -N concentrations at HRT of 0.5, 1.0, and 2.0 hr in the system were 0.26~0.32, 0.31~0.56, and 0.43~l.45 mg/L, respectively. The ranges of daily removal rates of TAN in this system were 20.03~23.0 g TAN/㎥ㆍday and those of nitrite nitrogen were 19.65~30.25 g NO$_2$$^{[-10]}$ -N/㎥ㆍday.

• Polymer(Korea)
• /
• v.31 no.3
• /
• pp.189-193
• /
• 2007

We developed the doxorubicin-loaded PLGA double-layered microspheres using relatively simple oil-in-water (O/W) solvent evaporation method for sustained release of doxorubicin and investigated the release behavior according to PLGA molecular weight and initial drug loading. The double-layered microsphere was characterized on the surface, the cross-section morphology, the behavior of doxorubicin release for 5 weeks by SEM and fluorescence spectrophotometer. Double-layered microspheres showed smooth surfaces and clear difference between core and outer-shell. As the PLGA molecular weight increased, the release rate of doxorubicin-loaded, double-layered microspheres decreased. These results showed that the release behaviors can be controlled by the variation of molecular weight of PLGA.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.671-678
• /
• 2000

Reaction characteristics of simultaneous removal of SOx and NOx have been investigated in a thermogravimetric analyzer and tubular fixed bed reactor using the $CuO/{\gamma}-Al_2O_3$ sorbent/catalyst. Sulfur removal capacity of $CuO/{\gamma}-Al_2O_3$ sorbent/catalyst is largely enhanced above both the temperature of $450^{\circ}C$ and the loading of 6wt% due to the participation of alumina support in a sulfation reaction. The NO reduction efficiency of 8wt% $CuO/{\gamma}-Al_2O_3$ sorbent/catalyst shows the maximum value at $370^{\circ}C$ and then decreases with the increase of reaction temperature due to the oxidation of $NH_3$ gas. The presence of sulfate on the surface of sorbent/catalyst enhances the optimum reaction temperature showing the maximum deNOx efficiency. In the simultaneous removal of SOx and NOx at $250^{\circ}C$. deNOx activity of $CuO/{\gamma}-Al_2O_3$ sorbent/catalyst is rapidly decreased due to the formation of ammonium salts such as $NH_4HSO_4$. In the simultaneous removal reaction of SOx and NOx, the optimum temperature showing the maximum deNOx efficiency increases to $400^{\circ}C$ due to the presence of $SO_2$ gas.