• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.10
• /
• pp.103-108
• /
• 2004

In this paper, a compact patch antenna with four T-slits fed by crossed aperture coupling is proposed for miniaturized Portable GPS handsets. The mechanism for compact size antenna is investigated with the behavior of the currents on the radiating patch. The equivalent surface current path due to the slits is lengthened, reducing the resonant frequency at a fixed patch size. The results of embedded T-slits for compact antenna size show that the resonant frequency is significantly lowered from 2.545GHz to 1.575GHz, corresponding to a 44.65% antenna size reduction compared to reference design. Experimental results show that good CP radiation patterns are obtained and impedance bandwidth (VSWR $\leq$ 2), 3dB axial ratio are about 21MHz, 19MHz at the center resonant frequency, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.719-722
• /
• 2003

Ferroelectric $Pb(Zr_{1-x}Ti_x)O_3$ (PZT) films were deposited on (001) MgO single crystals using sol-gel method. Structural properties and surface morphologies of PZT films were investigated using an X-ray diffractometer and a scanning electron microscopy, respectively. The dielectric properties of PZT films were investigated with the dc bias field using interdigitated capacitors (IDC) which were fabricated on PZT films using a thick metal layer by photolithography and dry etching process. The small signal dielectric properties of PZT films were calculated by a modified conformal mapping method with low and high frequency data, such as capacitance measured by an impedance gain/phase analyzer at 100 kHz and reflection coefficient (S-parameter) measured by a HP 8510C vector network analyzer at 1 -20 GHz. The IDC on PZT films exhibited about 67% of capacitance change with an electric field of 135 kV/cm at 10 GHz. These PZT thin films can be applied to tunable microwave devices such as phase shifters, tunable resonators and tunable filters.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.1
• /
• pp.54-66
• /
• 2012

The phase-shift method and correlation constants, which are unique electrochemical impedance spectroscopy techniques for studying the linear relationship between the phase shift ($90^{\circ}{\geq}-{\varphi}{\geq}0^{\circ}$) vs. potential (E) behavior for the optimum intermediate frequency ($f_o$) and the fractional surface coverage ($0{\leq}{\theta}{\leq}1$) vs. E behavior, are proposed and verified to determine the Frumkin, Langmuir, and Temkin adsorption isotherms and the related electrode kinetic and thermodynamic parameters. At Ni/0.5 M $H_2SO_4$ and 0.1M LiOH aqueous solution interfaces, the Frumkin and Temkin adsorption isotherms (${\theta}$ vs. E) of H for the cathodic hydrogen ($H_2$) evolution, interaction parameters (g), equilibrium constants (K), standard Gibbs energies (${\Delta}G^0_{\theta}$) of H adsorption, and rates of change (r) of ${\Delta}G^0_{\theta}$ with ${\theta}$ have been determined using the phase-shift method and correlation constants. A lateral repulsive interaction (g>0) between the adsorbed H species appears. The value of K in the alkaline aqueous solution is much greater than that in the acidic aqueous solution.

• Journal of Electrochemical Science and Technology
• /
• v.3 no.2
• /
• pp.80-84
• /
• 2012

The polyaniline (PANI) electrodes are prepared by chemical synthesis and electrodeposition methods and their supercapacitive properties are characterized and compared by morphology observation, cyclic voltammetry as a function of scan rate, and impedance spectra analysis. In particular, the supercapacitive properties obtained in the range of higher potential scan rates (e.g., over $200mV\;s^{-1}$) are emphasized to be capable of utilizing adequately the high power capability of supercapacitor. As a result, the PANI electrode by the electrodeposition shows superior specific capacitance (max. $474F\;g^{-1}$ at $10mV\;s^{-1}$ and about $390F\;g^{-1}$ at $500mV\;s^{-1}$) than those by the chemical synthesis method. This is mainly due to highly porous structure obtained by the electrodeposition to yield higher specific surface area.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.5
• /
• pp.51-56
• /
• 2008

In this paper, we propose a printed planar antenna suitable for mobile wireless communications. Since the printed antenna is easy to fabricate due to simplicity, low cost, and light weight, it is widely used in communications systems. The conventional patch antenna takes too much surface area to be applied to a mobile receiver. Although the size is reduced using the printed antenna, still reasonably wide bandwidth should be considered. To overcome the disadvantage of narrow bandwidth, the substrate should be physically thick and the dielectric constant should be small. In this work, we suggest a simple form of printed planar antenna and show the optimal input impedance depending on the antenna size and operating frequency. The performance evaluation is achieved analytically for a prototype antenna model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.100-106
• /
• 2009

A novel 8 V DC power source with an external series-parallel connection of 50 Dye-sensitized Solar Cells (DSCs) has been proposed. One DSC has the optimized length to width ratio of $5.2{\times}2.6\;cm$ and an active area $8\;cm^2$ ($4.62{\times}1.73\;cm$) which attained a conversion efficiency of 4.02%. From the electrochemical impedance spectroscopic analysis, it was found that the resistance elements related to the Pt electrode and electrolyte interface behave like that of diode and the series resistance corresponds to the sum of the other resistance elements. Surface morphology and sheet resistance of Pt counter electrode did not degrade the performance of the cell. This novel 8V-0.33A DC power source shows stable performance with an energy conversion efficiency of 4.24% under 1 sun illumination (AM 1.5, Pin of $100\;mW/cm^2$).

• Journal of Advanced Navigation Technology
• /
• v.10 no.4
• /
• pp.326-332
• /
• 2006

In this study, the antenna was proposed for the omni-directional characteristic in horizontal plane. Therefore we proposed $1{\times}4$ microstrip patch array on cylindrical surface for studying microstrip patch antennas. This antenna is designed for 2.45GHz ISM band and applications. This antenna can be applied to the base station of wireless microphone and access point of wireless LAN. The length and width of the patch antenna and the width of the feed line were calculated by using the theory of microstrip patch antenna, by using the both the 2.5D and 3D EM simulators the optimized antenna characteristics are obtained. From result of measured, antenna's impedance of coaxial waveguide port was 51.915-j3.688 ${\Omega}$, the return loss was -31dB and VSWR was 1.081.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.242.2-242.2
• /
• 2014

Plasma-polymer thin films (PPTF) have been deposited on a Si(100) wafer and glass under several conditions such as different RF power by using plasma-enhanced chemical vapor deposition (PECVD) system. Ethylcyclohexane, ammonia gas, hydrogen and argon were utilized as organic precursor, doping gas, bubbler gas and carrier gases, respectively. PPTFs were grown up with RF (ratio frequency using 13.56 MHz) powers in the range of 20~60 watt. PPTFs were characterized by FT-IR (Fourier Transform Infrared), FE-SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope), Contact angle and Probe station. The result of FT-IR measurement showed that the PPTFs have high cross-link density nitrogen doping ratio was also changed with a RF power increasing. AFM and FE-SEM also showed that the PPTFs have smooth surface and thickness. Impedance analyzer was utilized for the measurements of C-V curves having different dielectric constant as RF power.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.5
• /
• pp.399-406
• /
• 2014

Underwater acoustic materials are installed in order to reduce reflection, transmission and radiation of an underwater structure. The acoustic performance of the materials should be evaluated in accurately-controlled environment in terms of temperature and static pressure. In this paper, two pulse tubes, which are equipped with temperature and pressure controllers, are designed and developed to evaluate echo reduction(ER) and transmission loss(TL) of underwater acoustic materials. The procedures of the evaluation are suggested and the validation is carried out by comparing theoretical values to experimental results for a simple stainless steel specimen and free surface. In result, it is validated that developed pulse tubes are able to measure ER and TL with 2 dB tolerance.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.49-55
• /
• 2001

Josephson junction arrays were fabricated by DC magnetron sputtering, self-aligning and reactive ion etching technique. The Al native oxide, formed by thermal oxidation, was used as the tunneling barrier of Nb/$Al-A1_2$$O_3$Nb trilayer. The arrays have 2,000 Josephson junctions with the area of $14\mu\textrm{m}$ $\times$ $46\mu\textrm{m}$. The gap voltages were in the range of 2.5 ~2.6 mV and the spread of critical current was $\pm$11~14%. When operated at 70~94 ㎓, the arrays generated zero-crossing steps up to 2.1~2.4 V. To improve transmission of microwave power and prevent diffusion of oxygen into Nb ground-plane while depositing $SiO_2$dielectric, we applied a plasma nitridation process to the Nb ground-plane. The microwave power was well propagated in Josephson junction arrays with nitridation. The difference in microwave transmission 7an be interpreted by the surface impedance change depending on nitridation.