• Structural Engineering and Mechanics
• /
• 제65권4호
• /
• pp.453-464
• /
• 2018

In this paper, an efficient higher-order shear deformation theory is presented to analyze thermomechanical bending of temperature-dependent functionally graded (FG) plates resting on an elastic foundation. Further simplifying supposition are made to the conventional HSDT so that the number of unknowns is reduced, significantly facilitating engineering analysis. These theory account for hyperbolic distributions of the transverse shear strains and satisfy the zero traction boundary conditions on the surfaces of the plate without using shear correction factors. Power law material properties and linear steady-state thermal loads are assumed to be graded along the thickness. Nonlinear thermal conditions are imposed at the upper and lower surface for simply supported FG plates. Equations of motion are derived from the principle of virtual displacements. Analytical solutions for the thermomechanical bending analysis are obtained based on Fourier series that satisfy the boundary conditions (Navier's method). Non-dimensional results are compared for temperature-dependent FG plates and validated with those of other shear deformation theories. Numerical investigation is conducted to show the effect of material composition, plate geometry, and temperature field on the thermomechanical bending characteristics. It can be concluded that the present theory is not only accurate but also simple in predicting the thermomechanical bending responses of temperature-dependent FG plates.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1367-1372
• /
• 2008

A plate type supporting structure of a tube bundle in axial flow generates a certain band of a high frequency periodic excitation of a vortex shedding and/or a flow separation due to sharp edge of the plate thickness and a severe pressure drop due to a cross-sectional area of the supports. With a design consideration of the low vibration and a small flow resistance, the analysis method is uniquely confined to an experimental approach because a complex geometry of a cylindrical tube bundle and/or physical phenomena related to the fluid-structure interaction of tube bundle in a flow impede a theoretical or a numerical approach. A 5x5 cylindrical tube bundle with 5 supports which were discretely located along the bundle's axis was tested in the FIVPET hydraulic test loop for a design evaluation and an analysis perspectives. A high frequency flow-induced vibration of the supporting structures of the cylindrical tube bundle was measured at a outer surface of a supporting structure through a transparent flow housing by the laser dopper vibrometer. Pressure drop in-between three measurement distances was measured by the differential pressure transmitter. High frequency vibration and pressure drop fairly depends on the geometric design of supporting structure. So, these two parameters would be used as a qualitative design variables for design evaluation and analysis.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.141-147
• /
• 2014

This study aims to investigate the influence of bevel angles on the fatigue life of V-groove butt-welded joints with back-plates made by SM490A steel material, generally used for excavators, because changes in the geometry, material and surface properties of welded regions affect the fatigue life of welded structures. Butt type test specimens were prepared by the $CO_2$ welding of rolled steel plates (SM50A steel) with a thickness of 13.5 mm at a welding speed of 30 cm/min and these Butt type test specimens had two different groove angles, which are $40^{\circ}$ (A type) and $30^{\circ}$ (B type). In order to investigate differences in fatigue life between two types, 4-point bending fatigue tests were conducted with a stress ratio of R=0.1 under the cyclic loading environment at a frequency of 5 Hz at room temperature. The fatigue life of A type specimens was approximately 7% higher than that of B type specimens. The stress concentration factors calculated by finite element analysis were 2.16 for A type and 2.25 for B type, whose difference was caused by the influence of the back-plates of butt-welded structures. The current results could provide important guidelines to determine the V-groove angle of butt-welded joints with a satisfactory fatigue life, although under severe operating conditions.

• 한국도로학회논문집
• /
• 제20권4호
• /
• pp.73-84
• /
• 2018

PURPOSES : Most of the traffic surveys are carried out by an inspection method by the manpower. In some cases, the video equipment is used only in some regions when the traffic volume is surveyed. In this case, there is environmental restriction that the road equipment to fix the video equipment should exist. Also, in areas where information such as digital maps and satellite photographs is old or not provided, they are forced to rely on manpower research, but it is difficult to put huge amounts of time and money into the research in places where labor supply and demand is difficult. This difficulty is particularly pronounced in overseas business. METHODS : The purpose of this study is to improve the efficiency of business by using the drones in the traffic investigation through analysis of the cost reduction effect between the existing method and the proposed method in the overseas business traffic survey. The scope of the research is limited to the scope of research, and based on the case of overseas projects, the method of using drone for each research sector is suggested. RESULTS : In the traffic condition survey section, we propose the use of drone for traffic survey and queue length survey, and it is confirmed that there is a cost saving effect of 16% ~ 27% compared with the existing method. In the road condition survey, we propose the use of drones for road surface linear survey, geometry survey, and obstacle survey, and it was confirmed that the cost reduction effect is 39% ~ 93% compared to the existing method. CONCLUSIONS : In addition to overseas business, it is expected that it will have a positive effect on research time and cost reduction by using drone in traffic survey in domestic area where labor supply is not easy or basic data is insufficient.

• Journal of the korean society of oceanography
• /
• 제37권3호
• /
• pp.169-177
• /
• 2002

An eddy-resolving free-surface primitive-equation model with nonlinear terrain-following coordinates is established to study the exchange of water masses among the Asian marginal seas and their adjacent waters. A curvilinear coordinate system is used to generate the horizontal grid with a variable resolution for the regional oceans from $5^{\circ}$S to $45^{\circ}$N and $100^{\circ}$E to $155^{\circ}$E. The higher resolution region has about a 10 km by 10 km grid covering the complex geometry of the coastal marginal seas, while the lower resolution region has about a 30 km by 30 km grid covering the eastern Pacific. The model is initialized by the Levitus annual climitology and forced by the monthly mean air-sea fluxes of momentum, heat, and freshwater derived from the Comprehensive Ocean-Atmosphere Data Set. High-resolution and low-viscosity are identified as the key factors for a better representation of the exchange of waters through narrow straits and passages between the marginal seas and their adjacent waters. The dynamics of the loop currents and eddies in the South China Sea and Celebes Sea are examined in detail. It has found that the anticyclonic loop and detached eddies from the Kuroshio through the Luzon Strait play an important role in transporting warm and salty water into the South China Sea, while the cyclonic circulation of the Mindanao Current in the Celebes Sea plays a role in contributing cold water to the Indonesian throughflow. The deep undercurrent of the western Pacific is shown to provide fresher water to the South China Sea and Celebes Sea. These modeling results suggest that the exchange processes via the narrow straits and passages are of fundamental importance to the maintenance of water masses for the marginal sea region.

• 한국진공학회지
• /
• 제14권3호
• /
• pp.132-137
• /
• 2005

국내 유일의 연구용 원자로인 하나로에 중성자 반사율 측정장치를 개발 설치하였다. 하나로 중성자 반사율 측정장치는 수직형 시료 배치를 가지며 입사 중성자 빔의 파장은 $2.459\;\AA$이다. 원자로 출력 24 MW에서 금줄방사화법을 이용하여 측정한 단색기 및 시료위치에서의 중성자속은 각각 $4.5\times10^9\;n/cm^2/sec,\;6.64\times10^6\;n/cm^2/sec4이었다. 또한 하나로 중성자 반사율 측정장치를 이용하여 d-PS, $SiO_2$등의 일부 기준 박막 시료에 대하여 반사율을 측정하고 구조 분석을 수행하였다. 장치 성능 평가 결과 장치 최소 반사율은 $\sim10^{-6}$, 측정 가능한 Q 영역은 $0.003\sim0.3\;\AA^{-1}$이었다.

• 대한기계학회논문집A
• /
• 제36권12호
• /
• pp.1591-1597
• /
• 2012

복합재료 접합부의 접착강도에 대한 접착면 성질의 영향을 알아 보기 위해 불포화폴리에스테르, 우븐과 매트 유리섬유를 사용하여 복합재료 접합시편들을 제작하였다. 접착제, 복합재료 접착물, 말단접합과 이차접합 시편들의 기계적 성질을 실험에 의해 구하고 실험결과를 접합이론에 적용하였다. 6 개의 접합부들에서 발생하는 최대 및 평균 전단 응력은 최대 인장력과 접합 시편의 기하학적 변수들로부터 계산되었다. 실험 결과 접합면을 연마한 후 아세톤으로 처리한 경우가 말단접합의 3 가지 형태 중 가장 큰 강도를 가지고 있음이 관찰되었다. 마찬가지로 매트-매트와 매트-우븐 접합이 거의 같은 값으로 이차 접합의 3 가지 형태 중 가장 큰 강도를 가지고 있었다. 반대로 아무 처리도 하지 않은 접합시편과 우븐-우븐 접합시편은 매우 낮은 강도를 가졌다. 각각의 경우 파손은 접합부 양끝에서 심하게 발생하였고 접합부 가운데로 이동하였다.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1456-1464
• /
• 1993

본 논문에서는 다이아몬드 공구를 사용한 절삭과정에 대하여 절삭력 관계식을 제안하고, 이를 실제 천연 다이아몬드 공구를 이용하여 알루미늄 합금을 절삭하는 실험해석을 통하여 절삭력을 예측하는 모델을 세우고자 한다.

• 한국진공학회지
• /
• 제7권2호
• /
• pp.118-126
• /
• 1998

반도체 접촉구를 메우기 위하여 소오스의 직진성을 향상시키기 위한 연구를 수행하 였다. 이온화클러스터빔 증착법을 이용하는 동시에 셀의 구조를 개선하여 직진성 향상을 도 모하였다. 중성클러스터 만으로 구리를 증착할 경우 직진성은 매우 우수하였으나 소오스의 표면 이동이 적어 박막은 주상형으로 성장하며 측벽에의 증착은 거의 일어나지 않았으며 성 장에 따라 그림자효과로 인한 단차에서의 벽개가 관찰되었다. 그러나, 가속전압을 인가하여 전하를 띤 클러스터를 형성시켜 증착하였을 때 주상형 성장 모드는 사라졌으며, 직경 0.5$\mu$ m, aspect ratio 2의 접촉구에서 완벽한 바닥면의 도포성을 나타내었고, 측벽에의 증착성도 향상되어 막의 연결성이 개선되었다. 이로써 이온화 클러스터빔 증착법이 직진성을 향상시 켜 작은 접촉구의 메움을 향상시킬수 있는 물리적 증착 방법임을 확인하였다.

• 한국수자원학회논문집
• /
• 제43권2호
• /
• pp.233-243
• /
• 2010

하도의 횡단 및 종단 지형자료와 조도계수를 이용하여 자연하천에 대한 Muskingum-Cunge 모형의 매개변수들을 추정하는 방법을 제안하였다. 우선 각 단면에서의 다양한 수위에 대하여 통수단면 및 동수반경을 계산한 후, Manning 공식을 이용하여 유량을 산정한다. 이러한 과정은 하도에서의 모든 단면에 대하여 반복되며, 최종적으로 통수단면과 유량을 통한 회귀 분석에 의하여 매개변수들을 추정한다. 이와 같은 Muskingum-Cunge 모형의 매개변수 추정과정을 남한강 구간에 적용하였다. 추정된 매개변수들을 사용한 Muskingum-Cunge 모형의 계산결과는 무차원 RMS 오차, 첨두유량의 크기 및 발생시각 등 모든 면에서 HEC-1의 Muskingum-Cunge 모형에 비하여 동역학적 모형의 계산결과와 잘 일치하는 것으로 나타났다.