• 제목/요약/키워드: Surface flatness

검색결과 129건 처리시간 0.023초

이차전지 전극제조용 열간압연롤러와 전극재료의 열 변형 및 스프링백 해석 (Analysis of a Hot Rolling Roller and Spring-back of Electrode Materials for Secondary Batteries)

  • 김경식;김철
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2008년도 추계학술대회A
    • /
    • pp.538-543
    • /
    • 2008
  • A roller with a shaft and hot oil paths for pressing electrodes of polymer batteries were modeled and analyzed by FEM. There are many hot oil tubes in the roller and shaft, through which $72^{\circ}C$ hot oil flows for heating the surface of a roller and shaft. Thermal deformations and temperatures distributions of the roller and shaft were calculated and a convection boundary condition on surfaces was used. The influence of existence of a groove in the shaft on the flatness of a roller surface caused by thermal deformation was investigated. In addition, the amount of spring-back of electrodes under vacuum pressure and heating was calculated after the hot rolling process. It was shown from this study that the groove in one shaft had a favorable effect on the surface flatness.

  • PDF

마이크로 UV 성형을 통한 초소형 광픽업용 마이크로 미러 어레이 제작 (Fabrication of micro mirror array for small form factor optical pick-up by micro UV-molding)

  • 최용;임지석;김석민;손진승;김해성;강신일
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2005년도 춘계학술대회 논문집
    • /
    • pp.47-50
    • /
    • 2005
  • In this study, micro mirror array for small form factor optical pick-up was replicated by micro UV-molding. First, mold for micro mirror array was fabricated using micromachining. Also, to analyze the characteristics of the surface quality, flatness of replicated mirror surface were measured by white light scanning inteferometry system. The results show that the micro mirror array with a sufficient surface quality can be obtained by polymer replication process.

  • PDF

시공표면평탄에 따른 3D 프린팅 적층형상 정량분석 (Quantitative Analysis of 3D Printing Layered Shape according to the Flatness of Construction Surface)

  • 박진수;김경택
    • 대한토목학회논문집
    • /
    • 제42권2호
    • /
    • pp.257-261
    • /
    • 2022
  • 건축물의 디자인 자유도 향상, 작업자 안전 향상, 비교적 쉬운 납기예측 등의 이점으로 건설 산업에 적용된 3D 프린팅 기술(Additive manufacturing, AM)은 각종 효과성의 검증과 산업적용이 진행되고 있다. 다만, 기존기술대비 낮은 성숙도로 인해, 건축AM기술의 전주기에 발생하는 새로운 문제들을 해소하기 위한 연구들이 진행 중이다. 본 논문에서는 이러한 문제점 중에서도 현장 환경에 건축물을 적층 시공하는 과정에서, 낮은 시공표면평탄이 적층 제조 형상물에 미치는 영향을 확인한다. 특히 레이저 스캐닝을 통한 3차원 재구성 및 정량 분석을 통해, 낮은 평탄도로 인한 불균일한 적층형상물을 분석하고, 이를 해소하기 위한 적층시공전략을 제안한다.

액체생검용 Lab-on-a-Disc의 평탄도 향상을 위한 최적화 (Design Optimization to achieve an enhanced flatness of a Lab-on-a-Disc for liquid biopsy)

  • 홍석관;이정원;황택용;이성훈;김경태;강태곤;황철진
    • Design & Manufacturing
    • /
    • 제17권1호
    • /
    • pp.20-26
    • /
    • 2023
  • Lab-on-a-disc is a circular disc shape of cartridge that can be used for blood-based liquid biopsy to diagnose an early stage of cancer. Currently, liquid biopsies are regarded as a time-consuming process, and require sophisticated skills to precisely separate cell-free DNA (cfDNA) and circulating tumor cells (CTCs) floating in the bloodstream for accurate diagnosis. However, by applying the lab-on-a-disc to liquid biopsy, the entire process can be operated automatically. To do so, the lab-on-a-disc should be designed to prevent blood leakage during the centrifugation, transport, and dilution of blood inside the lab-on-a-disc in the process of liquid biopsy. In this study, the main components of lab-on-a-disc for liquid biopsy are fabricated by injection molding for mass production, and ultrasonic welding is employed to ensure the bonding strength between the components. To guarantee accurate ultrasonic welding, the flatness of the components is optimized numerically by using the response surface methodology with four main injection molding processing parameters, including the mold & resin temperatures, the injection speed, and the packing pressure. The 27 times finite element analyses using Moldflow® reveal that the injection time and the packing pressure are the critical factors affecting the flatness of the components with an optimal set of values for all four processing parameters. To further improve the flatness of the lab-on-a-disc components for stable mass production, a quarter-disc shape of lab-on-a-disc with a radius of 75 mm is used instead of a full circular shape of the disc, and this significantly decreases the standard deviation of flatness to 30% due to the reduced overall length of the injection molded components by one-half. Moreover, it is also beneficial to use a quarter disc shape to manage the deviation of flatness under 3 sigma limits.

  • PDF

거칠기 위치에 따른 이중관 내의 난류유동 (Turbulent flow in annuli depending on the position of roughness)

  • 안수환;김경천
    • 대한기계학회논문집B
    • /
    • 제21권7호
    • /
    • pp.891-899
    • /
    • 1997
  • This paper presents the results of a detailed experimental examination of fully developed asymmetric flows between annular tubes with square-ribbed surface roughness. The main emphasis of the research has been on establishing the turbulence structure, particularly in the central region of the channel where the two dissimilar wall flows interact. Measurements have included profiles of time mean velocities, turbulence intensities, turbulent shear stresses, triple velocity correlations, skewness, and flatness. The region of greatest interaction is characterized by strong diffusional transport of turbulent shear stress and kinetic energy from rough toward the smooth wall region, giving rise to an appreciable separation between the planes of zero shear stresses depending on positions of roughness on the walls.

12 인치 열-냉 척의 표면 열 변형 해석

  • 이상순;윤지영;김맹권
    • 한국반도체및디스플레이장비학회:학술대회논문집
    • /
    • 한국반도체및디스플레이장비학회 2003년도 추계학술대회 발표 논문집
    • /
    • pp.207-211
    • /
    • 2003
  • In this study, the geometric modeling has been conducted for a new model of 12 inch hot-cold chuck using three-dimensional solid modeler, SolidWorks. Then, the heat transfer analysis and the thermal deformation analysis using FEM have been performed. The results of the analysis show the temperature distribution and the deformed shape of a new model of 12 inch hot-cold chuck. The evaluation for the surface flatness of a new model has been performed based on the deformed shape obtained from ANSYS.

  • PDF

초음파 기술을 이용한 실리콘 이방성 식각 공정에서의 표면 평탄화 향상 연구 (Surface Flatness Improvement in Si Anisotropy Etching Process Utilizing Ultrasonic Wave Technology)

  • 윤의중;김좌연;이강원;이석태
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
    • /
    • pp.416-417
    • /
    • 2005
  • In this study, we optimized the process of Si anisotropy etching by combing tetramethyl ammonium hydroxide (TMAH) etching process with ultrasonic wave technology. New ultrasonic TMAH etching apparatus was developed and it was used for fabricating a $20{\mu}m$ thick diaphragm for Si piezoresistive pressure sensors. Based on comparison study on etch rate and surface flatness, it was observed that the Si anisotropy etching methode with new ultrasonic TMAH etching apparatus (at 40 kHz/ 500 watt) was superior to conventional etching methods with TMAH or TMAH+ammonium persulfate(AP) solutions.

  • PDF

Fine Blanking의 가장자리 Bridge 최소화 방법에 관한 연구 (A Study on Edge Bridge Minimization of Fine Blanking Process)

  • 김기태
    • 한국기계가공학회지
    • /
    • 제12권4호
    • /
    • pp.108-113
    • /
    • 2013
  • Industrialization and modernization of the beginning of the IT industry is growing very fast. Since telecommunications industry was developed rapidly, technologies about miniaturization and high-precision of parts have been actively developed to lead information revolution. generally, the entire shear surface of the product applying fine blanking technology must be very precise. Fine blanking is used to save cost by avoiding post-processing of the product. When using press blanking, it spends a lot of money on the production by using many post-processing. Fine blanking typically used in 0.5~18 mm thick steel plate. Because a lot of post-processing cost can be used to process, except for fine blanking. In order to develop components "CHANCE CONTENTS" in the fine blanking process, the purpose of this study is to minimize the edge of the bridge, secured 95% of the material thickness of the shear surface using the 1.6 mm thickness of the material SPCC. Blanking process by introducing after changing thickness through forging process, due to change in vee-rring force and counter force, the experimental amount of depressions and flatness and the shear surface were analyzed.

Hot Plate 신뢰성 시험.평가시스템 개발 (Reliability Evaluation System of Hot Plate for Photoresist Baking)

  • 송준엽;송창규;노승국;박화영
    • 한국정밀공학회지
    • /
    • 제19권8호
    • /
    • pp.180-186
    • /
    • 2002
  • Hot Plate is the major unit that it used to remove damp of wafer surface, to strength adhesion of photoresist (PR) and to bake coated PR in FAB process of semiconductor. The badness of Hot Plate (HP) has directly influence upon the performance of wafer, it is necessary to guarantee the performance of HP. In this study, a reliability evaluation system has been designed and developed, which is to measure and to estimate thermal uniformity and flatness of HP in range of temperature 0~$250^\circC$. This system has included the techniques which measures and analyzes thermal uniformity using infrared thermal vision, and which compensates measuring error of flatness using laser displacement sensor For measuring flatness, a measurement stage of 3 axes are developed which adapts the precision encoder. The allowable error of this system in respect of thermal uniformity is less $than\pm0.1^\circC$ and in respect of flatness is less $than\pm$1mm . It is expected that the developed system can measure from $\Phi200mm\;(wafer 8")\;to\;\Phi300mm$ (wafer 12") and also can be used in performance test of the Cool Plate and industrial heater, etc.

TiN 코팅층 집합조직의 변화에 따른 마찰, 마멸과 내부식 특성 (The Characteristics of Frictional Behavior, Wear and Corrosion Resistance of Textured TiN Coated Layer)

  • 김희동;김인수;성동영;이민구
    • 한국소성가공학회:학술대회논문집
    • /
    • 한국소성가공학회 2003년도 춘계학술대회논문집
    • /
    • pp.99-104
    • /
    • 2003
  • TiN coated films show a good mechanical properties, high thermal properties and wear, erosion and corrosion resistance and are widely used as a coating materials in tools, ornaments, parts and semiconductors. In spite of these good properties, the fracture of TiN coated films occur during use. The fracture of TiN thin films is related to their microstructure. Especially, the life of TiN coated layer is related to the texture of the TiN films. One researcher suggested that the corrosion and erosion resistance of the TiN thin films is related to a uniform and dense structure of films. In this study, we studied the relationships between textures and friction coefficient, erosion and corrosion in TiN coated films. The flatness of (115) texture surface of TiN thin films is flatter than that of (111) texture surface. The friction coefficient of (115) texture surface of TiN thin films is similar with that of (111) texture surface. The wear resistance of (115) texture surface of TiN thin films is better than that of (111) texture surface. The erosion and corrosion resistance of (115) texture surface of TiN thin films is better than that of (111) torture surface. As well as texture, the wear, erosion and corrosion of TiN thin films has to consider defects such as pinholes, cracks, surface roughness and open columnar structure. The life of TiN coated products is influenced by the properties of wear, erosion, and corrosion resistance of TiN thin films and is related to texture of TiN coated films, density of pinholes and cracks, density of structure, and surface flatness.

  • PDF