• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.428-433
• /
• 2000

The consolidation behavior of multicomponent particles prepared by the flame hydrolysis deposition process is examined to identify the effects of Si substrate temperature. To fabricate multi-component particles, a vapor-phase ternary mixture of $SiCl_4(100 cc/min),\;BCl_3(30cc/min)\;and\;POCl_3,(5cc/min)$ was fed into a coflow diffusion oxy-hydrogen flame burner. The doped silica soot bodies were deposited on silicon substrates under various deposition conditions. The surface temperature of the substrate was measured by an infrared thermometer. Changes in the chemical states of the doped silica soot bodies were examined by FT-IR(Fourier-transformed infrared spectroscopy). The deposited particles on the substrate were heated at $1300^{\circ}C$ for 3h in a furnace at a heating rate of 10K/min. Si-O-B bending peak has been found when surface temperature exceeds $720^{\circ}C$. Correspondingly, the case with substrate temperatures above loot produced good consolidation result.

• 대한기계학회논문집B
• /
• 제25권9호
• /
• pp.1175-1182
• /
• 2001

Chemical compositions of polydisperse SiO$_2$/TiO$_2$multicomponent aggregates were measured for different heights from the burner surface and different mobility diameters of aggregates. SiO$_2$/TiO$_2$multicomponent particles were generated in a hydrogen/oxygen coflow diffusion flame from two sets of precursors: TTIP(titanium tetraisopropoxide), TEOS(tetraethylorthosilicate). To maintain 1:1 mole ratio of TTIP:TEOS vapor, flow rate of carrier gas $N_2$was fixed at 0.6lpm for TTIP, at 0.1lpm for TEOS. In-situ sampling probe was used to supply particles into DMA(differential mobility analyzer) which was calibrated with using commercial DMA(TSI, model 3071A) and classifying monodisperse multicomponent particles. Classified monodisperse particles were collected with electrophoretic collector. The distributions of composition from particles to particle were determined using EDS(energy dispersive spectrometry) coupled with TEM(transmission electron microscope). The chemical(atomic) compositions of classified monodisperse particle were obtained for different heights; z=40mm, 60mm, 80mm. The results suggested that the chemical(atomic) composition of SiO$_2$decreased with the height from burner surface and the composition of SiO$_2$and TiO$_2$approached to the value of 1 to 1 fat downstream. It is also found that the composition of SiO$_2$decreases as the mobility diameter of aggregate increases.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.441-446
• /
• 2000

Chemical compositions of monodisperse $SiO_2/TiO_2$ multicomponent aggregates were measured for different heights from the burner surface and different mobility diameters of aggregates. $SiO_2/TiO_2$ multicomponent particles were generated in a hydrogen/oxygen coflow diffusion flame from two sets of precursors: TTIP (titanium tetraisopropoxide), TEOS(tetraethylorthosilicate). To maintain 1:1 mole ratio of TTIP:TEOS vapor theoretically, flow rate of carrier gas $N_2$ was fixed at 0.61pm for TTIP, at 0.11pm for TEOS. In situ sampling probe was used to supply particles into differential mobility analyzer(DMA) which was calibrated with using commercial DMA(TSI 3071A) and classifying monodisperse multicomponent particles. Classified particles were collected with electrophoretic collector. The distributions of composition from particle to particle were determined using EDS (energy dispersive spectrometry) coupled with TEM (transmission electron microscope). The chemical (atomic) compositions of classified monodisperse particle were obtained for different heights; z=40mm, 60mm, 80mm. The results suggested that the atomic composition of $SiO_2$ decreased with the height from burner surface and the composition of $SiO_2$ and $TiO_2$ approached to the value of 1 to 1 in far downstream. It is also found that the composition of $SiO_2$ decreases as the mobility diameter of aggregate increases.

• 대한기계학회논문집B
• /
• 제23권6호
• /
• pp.788-794
• /
• 1999

The swirl flame is mostly used to stabilize the flame on the burner nozzle in the industrial combustor. In the case of the weak swirl flame(S<0.4), the recirculation zone could not be formed, but in the strong swirl(S>0.6) flame, it could be formed in the center of the swirl flame. In this study, the measurement and analysis of emission species, temperature, radicals of premixed swirl flame in the combustor were performed to understand the NO formation and emission characteristics of the swirl flame of natural gas. The result of NO emission in the swirl flame is that the amount of NO emission in the strong swirl flame decreased about 60% compared with that of the weak swirl flame. The main region of NO formation of the weak swirl flame is positioned in the down stream(z=100~200mm) of the flame, but that of the strong swirl flame is positioned in the up stream(z=40mm) where the recirculation zone seems to be formed. It is supposed that the increase of flame surface and the formation of inversed flame cause the reduction of the high temperature region on the production of NO in the strong swirl flame. The result of NO-temperature relation revealed that the factor of NO formation is not only temperature but also another parameters in the weak swirl flame, but in the strong swirl flame, NO is proportional to the temperature of higher than 1200K.

• 한국안전학회지
• /
• 제27권3호
• /
• pp.71-76
• /
• 2012

The coflow velocity effect on the minimum extinguishing concentration(MEC) was investigated experimentally in heptane cup-burner flames. Various inert gases($N_2$, Ar, $CO_2$, He) were added into the oxidizer to find the critical concentration and the effectiveness of the agents on flame extinction. The experimental results showed that the MECs were increased with increasing coflow velocity for most inert gases except helium, but the higher coflow velocity induced the lower burning rates of heptane. This indicated that the increase of coflow velocity resulted in the decrease of fuel velocity evaporated from fuel surface, and hence the stain rate on the reaction zone was also decreased. In the case of helium as a additive, the extinguishing concentration was independent of the coflow velocity because the heat conductivity was ten times larger than the other inert gases and flow effect by a strain rate might be compensated for heat loss to the surroundings.

• 에너지공학
• /
• 제11권2호
• /
• pp.166-177
• /
• 2002

본 연구는 화염안정을 위해 약간의 메탄을 첨가한 1차원, Hat, 예혼합, 층류 석탄-공기 화염구조에 관한 연구로서 반응영역을 늘리기 위해 0.3 atm에서 운전되는 저압버너를 사용하였다. 본 연구에서는 가스 온도, 주요가스의 농도, 샘플된 촤의 분석과 화염속도에 대하여 여러 모델들의 해석결과를 실험결과와 서로 비교하였다. 여러 모델중 촤 표면적 지수(S=4)와 휘발성분에 대해 각각의 탈휘발화 속도상수를 적용한 model II $I^{*}$ -d가 실험치와 비교적 일치함을 보여주었다. 샘플된 촤의 분석 결과 입자의 반응이 낮게 예측되어져 촤 표면적지수를 증가시켜야만 했다. 이 지수는 촤의 반응 표면적에 대한 민감도 분석으로부터 얻어진 결과였고 model II $I^{*}$ -d의 화염속도 해석결과는 대부분의 측정치에 근접한 결과를 보여주고 있다. 고체 입자 직경은 열적 지연과 반응표면적을 통하여 탈휘발화율과 촤 산화에 큰 영향을 주며 이는 곧 화염속도에 영향을 주고 있음을 보여주었다.

• 대한기계학회논문집B
• /
• 제23권11호
• /
• pp.1379-1389
• /
• 1999

A new technique for control of size and shape of flame-made particles is Introduced. The characteristic sintering time can be controlled Independently of collision time by heating the particles with irradiation of laser because the sintering time strongly depends on temperature. A coflow oxy-hydrogen diffusion flame burner was used for $SiCl_4$ conversion to silica particle. Nanometer sized aggregates irradiated by a high power CW $CO_2$ laser beam were rapidly heated up to high temperatures and then were sintered to approach volume-equivalent spheres. The sphere collides much slower than the aggregate, which results in reduction of sizes of particles maintaining spherical shape. Light scattering of Ar ion laser and TEM observation using a local sampling device were used to confirm the above effects. When the $CO_2$ laser was irradiated at low position from the burner surface, particle generation due to gas absorption of laser beam occurred and thus scattering intensity increased with $CO_2$ laser power. At high irradiation position, scattering intensity decreased with $CO_2$ laser power and TEM image showed a clear mark of evaporation and recondensation of particles for high $CO_2$ laser power. When the laser was irradiated between the above two positions where small aggregates exist, average size of spherical particles obviously decreased to 58% of those without $CO_2$ laser irradiation with the spherical shape. Even for increased carrier gas flow rate by a factor of three, TEM photograph also revealed considerable reduction of particle size.

• 한국안전학회지
• /
• 제20권4호
• /
• pp.171-179
• /
• 2005

건물의 마감재료가 화재에 노출될 때 그 마감재료의 역할을 이해하는 것은 필수적이다. 실물화재실험을 통해서 재료의 성능을 평가하는 것이 가능하다. 그러나 실물화재 실험 시 소요되는 시간과 높은 비용으로 인해 실물 화재 실험이 수행되는 경우는 드물고 대신 컴퓨터 화재 시뮬레이션이 개발되어 왔다. 컴퓨터 화재 시뮬레이션에서는 초기입력 데이터로서 점화 버너의 화염으로부터의 Heat Flux Map이 요구된다. 현재까지의 연구에서는 열전대 혹은 열유속 센서와 같은 실험장치의 제한으로 인해 $10kW/m^2$간격의 Heat Flux Map이 나와있을 뿐이고 공간적으로 더 상세한 Heat Flux Map은 없는 실정이다. 화재 시뮬레이션의 성능을 증가시키기 위해서는 점화 버너로부터의 정확하고 상세한 Heat Flux Map이 필요불가결하다. 본 연구의 목적은 적외선 카메라로부터 얻어진 표면온도를 이용하여 벽에서 점화 버너 화염에 대한 Heat Flux Happing Procedure를 개발하는 것이다. 높은 수준의 공간적 해상도는 적외선 카메라로부터 제공된다. 개발된 Heat Flux Mapping Procedure를 증명하기 위해서 ISO 9705 점화버너를 이용해서 실험이 행해졌다. 실험 결과를 통해 개발된 Heat Flux Mapping방법의 열유속 해상도와 공간적 해상도가 얻어졌다. 또한 그 실험 결과가 현재 쓰여지고 있는 Heat Flux Map과 비교되었다.

• 한국표면공학회지
• /
• 제42권3호
• /
• pp.139-144
• /
• 2009

A microwave plasma torch at the atmospheric pressure by making use of magnetrons operated at the 2.45 GHz and used in a home microwave oven has been developed. This electrodeless torch can be used to various areas, including industrial, environmental and military applications. Although the microwave plasma torch has many applications, we in the present work focused on the microwave plasma torch operated in pure steam and several applications, which may be used in future and right now. For example, a high-temperature steam microwave plasma torch may have a potential application of the hydrocarbon fuel reforming at one atmospheric pressure. Moreover, the radicals including hydrogen, oxygen and hydroxide molecules are abundantly available in the steam torch, dramatically enhancing the reaction speed. Also, the microwave plasma torch can be used as a high-temperature, large-volume plasma burner by injecting hydrocarbon fuels in gas, liquid, and solid into the plasma flame. Finally, we briefly report treatment of soils contaminated with oils, volatile organic compounds, heavy metals, etc., which is an underway research in our group.

• Journal of the Korean Wood Science and Technology
• /
• 제49권1호
• /
• pp.44-56
• /
• 2021

소방청의 방염성능기준에 제시된 45°멕켈 버어너법을 이용하여 물유리 농도와 첨가제 종류에 따른 합판의 탄화길이 및 면적 등의 방염성능을 측정하였다. 합판에 농도 20-50%의 물유리를 처리한 결과, 방염성능은 물유리의 농도와 비례하는 경향을 나타냈다. 그러나 30%를 넘는 고농도의 물유리로 처리된 합판의 표면에서 백화현상과 끈적임이 발생하여 농도 30%를 최적 조건으로 결정하였다. 농도 30%의 물유리에 서로 다른 비율의 첨가제를 추가하여 실험을 수행한 결과, 수산화칼륨 15% 조건과 수산화알루미늄 1-10%의 조건에서 방염성능 기준을 만족하였다. 반면에 황산마그네슘은 방염성능에 크게 영향을 미치지 않았다. 물유리와 첨가제에 따른 방염성능의 결과는 방염제를 활용한 불연재에 대한 기초자료로 활용될 것으로 기대된다.