• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.75-76
• /
• 2015

This study has examined the impact resistance and blast resistance characteristics of HPFRCC as a research on impact resistance and blast resistance characteristics using high volume mortar and high velocity projectile for evaluating the protection performance of actual buildings as small quantity experiment of laboratory conditions is performed although there was an instance of performing research on mortar that has reinforced fiber followed by the rise of problems on the damage of human life and buildings created due to explosion and shock. As a result, the destruction loss area and depth have decreased in case of the surface compared to the rear side. As tensile strength and tenacity have increased with the increased fiber replacing ratio, a tendency of destruction loss area and depth getting decreased was shown as the impact resistance has increased.

• Resources Recycling
• /
• v.21 no.3
• /
• pp.39-47
• /
• 2012

This study was conducted to optimize a mixing design of lightweight aerated concrete with the blast furnace slag(BFS) using Box-Behnken method, one of response surface designs. The lightweight aerated concrete with the BFS was made on the conditions of steam curing method at atmospheric pressure. The experimental factors were unit Water(W)/total powder($P_d$) ratio, BFS replacement percentage and Al powder addition based on the total powder (${P_d}^*$%). From the results of the response surface analysis, regression models for dried specific gravity and compressive strength of the lightweight aerated concrete were derived. When the target values for dried specific gravity and compressive strength of the lightweight aerated concrete were set at 0.72 and 4.42 MPa respectively, its optimized mixing conditions driven from the regression models were 0.62 of $W/P_d$ ratio, 35.5% of BFS replacement and 0.05% of Al powder addition. This experimental design model was found to be credible by measuring the dried specific gravity and compressive strength of the sample made from the above mixing conditions.

• Explosives and Blasting
• /
• v.24 no.2
• /
• pp.51-63
• /
• 2006

The typical blasting method adopted in Pasir Coal Mine is a surface blasting technique with a single free face. It means that there is only one free face, which is usually the ground surface. This kind of blasting method is easy to use but inevitably causes enormous ground vibrations, which, in turn, can affect the stability of the slopes comprising the various boundaries of the open pit mine. In addition, the method also has the problem of lowering the overall blast efficiency compared to other methods such as bench blasting methods or ones with more than two free faces. In this respect, a project was launched to develop a new blasting method that is suitable for both controling the ground vibration and enhancing the blast efficiency. As a part of the project, we investigated the current blasting method of the mine, and have conducted field measurements of the ground vibrations from 12 biasts. This Paper presents the details of the typical blasting pattern and the Propagation characteristics of the ground vibration from the surface blasting in the mine. Especially, various predictive equations for peak Particle velocities that can be used to estimate the ground vibration level in the mine area were derived from the regression analyses using the measured ground vibration data.

• Korean Journal of Soil Science and Fertilizer
• /
• v.18 no.4
• /
• pp.386-391
• /
• 1985

In sandy paddy soil, the occurrence of leaf and neck blast was investigated depending upon nitrogen fertilizer application level of 10, 15, 20kg per 10a and different application method of surface application, whole layer application and integrated improvement. An occurrence of leaf and neck blast was significantly increased with increasing nitrogen application up to. 20kg/10a. Also a close relation between leaf and neck blast was observed. Effect of fungicides on blast control was 62.5-93.5 percent compared to those of no fungicides. Yield of unhulled rice was 604kg/10a in plots of no fungicides, however, it was 719kg/10a in plots with fungicides. Yield loss was 15.6% in case of blast infection.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.185-190
• /
• 2021

Cement has been used as a main material in the modern construction industry. However, it has been pointed out as a main cause of global warming due to carbon dioxide generated during manufactured. Recently, research that replacing cement substitute to industrial by-products such as Blast Furnace Slag which is by-producted in steelworks. When Blast Furnace Slag is used as a cement substitute, it shows a problem of lower initial strength, which is caused by glassy membrane on the particle surface. In this study, we used Electrolysis Alkaline Aqueous to improve the usability and problem of lower initial strength. As a result of the experiment, cement matrix using Blast Furnace Slag and Alkaline Aqueous showed initial strength and hydrate product were developed than that using general mixing water. Also, as a result of porosity analysis, It was confirmed that cement matrix using Alkaline Aqueous and Blast Furnace Slag has a tighter structure in internal porosity and porosity distribution than using general mixing water.

• Journal of the Korean Geosynthetics Society
• /
• v.18 no.1
• /
• pp.67-77
• /
• 2019

The grouting method is utilized to reinforce and waterproof poor grounds, enhance the bearing capacity of structures damaged resulting from settlement due to elevation and vibration or differential settlement, and for cutoff. The purpose of this research is to enhance the compressive strength of grout materials by using aramid fiber and develop a high-strength ground improvement method by using blast furnace slag powder. In this regard, this study has conducted a uniaxial compression test after checking the high charge (higher than 50%) of the ratio of blast furnace slag powder and cement at 100:0, 70:30 and 40:60%, adding the aramid mixture based on 0, 0.5 and 1.0% of the cement and furnace slag powder weight and creating sand gels based on surface oiling rate of 0.7 and 1.2%. For the environmental review evaluation, a heavy metal exudation test and a pH test measurement have been conducted. The experiment results showed that 1% increase of aramid fiber led to 1.3 times greater uniaxial compression intensity. As for the hexavalent chrome, a 30% increase in blast furnace slag powder led to approximately 50% decrease in heavy metal exudation. However, the pH test revealed that a 30% increase in blast furnace slag powder resulted in approximately 0.5 increase in pH. Further research on the pH part is needed in the future.

• Tribology and Lubricants
• /
• v.12 no.1
• /
• pp.15-21
• /
• 1996

Friction and wear properties of MoS$_2$ bonded films were studied using the Falex testing machine, and their properties were evaluated in terms of the life and the load carrying capacity of the films. MoS$_2$ bonded films were formulated from the mixtures of MoS$_2$ solid particles and epoxyphenol resin, and they were applied onto AISI 4130 steel surface by dipping method to form lubricating bonded films. The results of the life and the load carrying capacity of the films showed that films were mainly affected by the surface temperature arisen from the frictional heat at the contact surface. To obtain enhanced tribological properties of the films, various combinations of solid lubricants and additives with a basic polymer resin were attempted and evaluated. The effects of surface pretreatment, such as sand blast or Zn-phosphating, were also investigated.

• Explosives and Blasting
• /
• v.30 no.2
• /
• pp.29-42
• /
• 2012

Variables influencing the free face movement due to rock blasting include the physical and mechanical properties, in particular the discontinuity characteristics, explosive type, charge weight, burden, blast-hole spacing, delay time between blast-holes or rows, stemming conditions. These variables also affects the blast vibration, air blast and size of fragmentation. For the design of surface blasting, the priority is given to the safety of nearby buildings. Therefore, blast vibration has to be controlled by analyzing the free face movement at the surface blasting sites and also blasting operation needs to be optimized to improve the fragmentation size. High-speed digital image analysis enables the analyses of the initial movement of free face of rock, stemming optimality, fragment trajectory, face movement direction and velocity as well as the optimal detonator initiation system. Even though The high-speed image analysis technique has been widely used in foreign countries, its applications can hardly be found in Korea. This thesis aims at carrying out a fundamental study for optimizing the blast design and evaluation using the high-speed digital image analysis. A series of experimentation were performed at two large surface blasting sites with the rock type of shale and granite, respectively. Emulsion and ANFO were the explosives used for the study. Based on the digital images analysis, displacement and velocity of the free face were scrutinized along with the analysis fragment size distribution. In addition, AUTODYN, 2-D FEM model, was applied to simulate detonation pressure, detonation velocity, response time for the initiation of the free face movement and face movement shape. The result show that regardless of the rock type, due to the displacement and the movement velocity have the maximum near the center of charged section the free face becomes curved like a bow. Compared with ANFO, the cases with Emulsion result in larger detonation pressure and velocity and faster reaction for the displacement initiation.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.10
• /
• pp.13-25
• /
• 2021

The most widely used method for determining the blast effects of explosives is the Trauzl test. This test is used to measure the explosive power (strength) of a substance by determining volume increase, which is produced by the detonation of a tested explosive charge in the cavity of a lead block with defined quality and size. In this paper, Trauzl lead block test and High speed 3D-DIC (Digital Image Correlation) system were conducted to evaluate the stemming effect of the blast hole. The effects of stemming materials can be expressed as the expansion of the cavity in a standard lead block through explosion of the explosives. The blasting experiment was conducted with emulsion explosives. The stemming material in the blast hole of lead block, which was adopted in this study, were using sand and stone chips. Results of blasting experiment and numerical analysis showed that the expansion rates of lead block were most affected by stone chips followed by sand. Also, as result of dynamic strain measurement on the lead block surface of High speed 3D-DIC system, the displacement and surface strain on the block were the highest in the experiment case of stone chips stemming.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.692-705
• /
• 2018

Ground vibration is one of the remarkable issues in tunnel blasting. In recent studies, to improve the fragmentation with reduction of ground vibration in tunnel blasting, a vibration-controlled blasting method with artificial cutting slot near the center-cut holes has been suggested. This study examines the effect of the different arrangement of artificial cut-slot on the vibration reduction and fragmentation by performing the full-scaled concrete block blast experiments and the numerical simulations with 3D-DFPA. The results show that the existence of artificial slot contributes to the improvement of vibration reduction, blast fragmentation and the efficiency of the cutting slot blast. It can be explained that the artificial slot play a free surface role and should decrease the burden between the cut holes. Crater volumes of the blasted concrete blocks were measured by 3-dimensional digital image analysis and compared with the ideal standard crater volume which can be calculated by theoretical standard blast design method. As a result, the ratio of burden and hole diameter which should achieve the standard crater in the cut-hole blasting were suggested.