• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.3
• /
• pp.437-450
• /
• 1996

A set of stability equations is formulated for natural convection flows adjacent to a vertical isothermal surface melting in cold pure water. It takes account of the nonparallelism of the base flows. The melting rate is regarded as a blowing velocity at the ice surface. The numerical solutions of the linear stability equations which constitute a two-point boundary value problem are accurately obtained for various values of the density extremum parameter $R=(T_m-T_{\infty})/(T_0-T_{\infty})$ in the range $0.3{\leq}R{\leq}0.6$, by using a computer code COLNEW. The blowing effects on the base flow becomes more significant as ambient temperature ($T_{\infty}$) increases to $T_{\infty}=10^{\circ}C$. The maximum decrease of heat transfer rate is about 6.4 percent. The stability results show that the melting at surface causes the critical Grashof number $G^*$ and the maximum frequency of disturbances to decrease. In comparision with the results for the conventional parallel flow model, the nonparallel flow model has a higher critical Grashof number but has lower amplification rates of disturbances than does the parallel flow model. The spatial amplification contours exhibit that the selective frequency $B_0$ of the nonparallel flow model is higher than that of the parallel flow model and that the effects of melting are rather small. The present study also indicates that the selective frequency $B_0$ can be easily predicted by the value of the frequency parameter $B^*$ at $G^*$, which comes from the neutral stability results of the nonparallel flow model.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.96-101
• /
• 2005

Fluoropolymer of PTFE and PFA etc. is a heat resistance polymeric material that it is known as that maximum continuous use temperature reaches for 260 $^{\circ}C$. It was observed that these polymers had the enough thermal stability so enough that it was kept by thermal aging of 280 $^{\circ}C$/7 weeks too in this study. However, such thermal stability means that bulk material property is kept such as mechanical strength, melting point and initial pyrolysis temperature etc. If these polymers are evaluate by coating property such as surface contact angle, surface morphology, surface scratch, thing that heat resistance is not enough was confirmed in this study. Thermal aging of flouropolymer coating was achieved by gear aging oven that the exchange rate of air was controlled, and the analysis results were indicating serious damage of surface morphology and adhesive strength on metal substrate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.317.2-317.2
• /
• 2013

Ultrathin oxide encapsulated metal-oxide hybrid nanocatalysts have been fabricated by a soft chemical and facile route. First, SiO2 nanoparticles of 25~30 nm size have been synthesized by modified Stobber's method followed by amine functionalization. Metal nanoparticles (Ru, Rh, Pt) capped with polymer/citrate have been deposited on functionalized SiO2 and finally an ultrathin layer of TiO2 coated on surface which prevents sintering and provides high thermal stability while maximizing the metal-oxide interface for higher catalytic activity. TEM studies confirmed that 2.5 nm sized metal nanoparticles are well dispersed and distributed throughout the surface of 25 nm SiO2 nanoparticles with a 3-4 nm TiO2 ultrathin layer. The metal nanoparticles are still well exposed to outer surface, being enabled for surface characterization and catalytic activity. Even after calcination at $600^{\circ}C$, the structure and morphology of hybrid nanocatalysts remain intact confirm the high thermal stability. XPS spectra of hybrid nanocatalyst suggest the metallic states as well as their corresponding oxide states. The catalytic activity has been evaluated for high temperature CO oxidation reaction as well as photocatalytic H2 generation under solar simulation. The design of hybrid structure, high thermal stability, and better exposure of metal active sites are the key parameters for the high catalytic activity. The maximization of metal-TiO2 interface interaction has the great role in photocatalytic H2 production.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.23-32
• /
• 2003

The displacement measuring systems of slope ground surface are very expensive instruments and have disadvantages concerning installing, maintaining and surveying. The measuring works are very dangerous. Recently, simple systems are required to measure the displacement of slope ground surface in stages of cutting and maintaining slope. In this study, the mechanism of Softcopy Photogrammetry is applied to measure the displacement of slope ground surface. Three dimensional data of the slope ground surface can effectively be obtained in order to analyze slope stability. Computer Program, DIMA (Design IMmage Analysis), including the reformation process of a contour line was developed. As a result of this study, countermeasure and instruction standards of the displacement of slope ground surface before and after slope failure are established. Also, disadvantages of the existing system can be complemented.

• Journal of Powder Materials
• /
• v.24 no.1
• /
• pp.1-5
• /
• 2017

We have investigated the washing method of as-synthesized CdSe/ZnS core/shell structure quantum dots (QDs) and the effective surface passivation method of the washed QDs using PMMA. The quantum yield (QY%) of as-synthesized QDs decreases with time, from 79.3% to 21.1%, owing to surface reaction with residual organics. The decreased QY% is restored to the QY% of as-synthesized QDs by washing. However, the QY% of washed QDs also decreases with time, owing to the absence of surface passivation layer. On the other hand, the PMMA-treated QDs maintained a relatively higher QY% after washing than that of the washed QDs that were kept in toluene solution for 30 days. Formation of the PMMA coating layer on CdSe/ZnS QD surface is confirmed by HR-TEM and FT-IR. It is found that the PMMA surface coating, when combined with washing, is useful to be applied in the storage of QDs, owing to its long-term stability.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2001.06a
• /
• pp.3-3
• /
• 2001

Recently TiN, TiAlN, CrN hardcoatings have adapted many industrial application such as die, mold and cutting tools because of good wear resistant and thermal stability. However, in terms of high speed process, general hard coatings have been limited by oxidation and thermal hardness drop. Especially in the case of PCB drill, high speed cutting and without lubricant process condition have not adapted these coatings until now. Therefore more recently, superhard nanocomposite coating which have superhard and good thermal stability have developed. In previous works, WC-TiAlN new nanocomposite film was investigated by cathodic arc ion plating system. Control of AI concentration, WC-TiAlN multi layer composite coating with controlled microstructure was carried out and provides additional enhancement of mechanical properties as well as oxidation resistance at elevated temperature. It is noted that microhardness ofWC-TiA1N multi layer composite coating increased up to 50 Gpa and got thermal stability about $900^{\circ}C$. In this study WC-TiAlN nanocomposite coating was deposited on PCB drill for enhancement of life time. The parameter was A1 concentration and plasma cleaning time for edge sharpness maintaining. The characteristic of WC-TiAlN film formation and wear behaviors are discussed with data from AlES, XRD, EDS and SEM analysis. Through field test, enhancement of life time for PCB drill was measured.

• Journal of Periodontal and Implant Science
• /
• v.47 no.2
• /
• pp.106-115
• /
• 2017

Purpose: The possibility of immediate or early loading has become popular in implant dentistry. A prerequisite for the immediate or early loading of an implant prosthesis is the achievement of initial stability in the implant. Moreover, in response to clinicians' interest in verifying clinical stability to determine the optimal time point for functional loading, a non-invasive method to assess implant stability has been developed on the basis of resonance frequency analysis (RFA). The primary objective of this study was to monitor the stability of sandblasted, large-grit, and acid-etched (SLA) implants with different diameters during the early phases of healing by RFA. The secondary objective was to evaluate how the initial stability of implants varied depending on different surface modifications and other contributing factors. Methods: Thirty-five implants (25 SLA implants and 10 resorbable blasting media [RBM] implants) placed in 20 subjects were included. To measure implant stability, RFA was performed at baseline and at 1, 2, 3, 4, 6, and 10 weeks after surgery. Results: The longitudinal changes in the implant stability quotient (ISQ) values were similar for the SLA implants with different diameters and for the RBM implants. During the initial healing period, the ISQ decreased after installation and reached its lowest values at 1 week and 2 weeks, respectively. The mean ISQ values in the SLA implants were significantly higher in ${\varnothing}5.0mm$ implants than in ${\varnothing}4.0mm$ implants. Men showed a higher ISQ than women. Mandibular sites showed a higher ISQ than maxillary sites. Conclusions: All implants used in this study are suitable for immediate or early loading under appropriate indications. A wider diameter and SLA surface treatment of implants could improve the stability, if the implant is fixed with at least 30 Ncm of insertion torque.

• Journal of the Korean Ceramic Society
• /
• v.52 no.6
• /
• pp.497-501
• /
• 2015

Inkjet printing is a widespread technology, offering advantages such as high-quality decoration, a continuous process, and the accurate direct reproduction of patterns or pictures. In inkjet printing technology, the dispersion stability of ceramic ink is one of the most important factors. In this study, the dispersion stability of blue $CoAl_2O_4$ ink for ceramic inkjet printing is systematically investigated. Blue $CoAl_2O_4$ pigment was synthesized by a solid-state reaction and then milled to less than 300nm in size. In order to investigate the influence of the viscosity on the dispersion stability, two types of $CoAl_2O_4$ ceramic inks (termed here Blue L and Blue H) were prepared using different volume ratios of ethylene glycol and ethanol. The Blue L and Blue H ink solutions contained cetyltrimethylammonium bromide(CTAB) as a dispersive agent. The viscosity, surface tension and jetting stability of the $CoAl_2O_4$ ceramic inks were analyzed using a rheometer, a surface tension meter and a dropwatcher. The dispersion stability of the $CoAl_2O_4$ ceramic ink was investigated by a multiple light-scattering method. Blue H, a ceramic ink with higher viscosity, showed much better dispersion stability than the Blue L ceramic ink.

• 한국체육학회지인문사회과학편
• /
• v.54 no.1
• /
• pp.505-514
• /
• 2015

The purpose of this study was to examine the muscle activation in trunk and low-limbs muscle during squat exercise on various instability surface. 10 subject performed squat with 75% of 1 repetition maximum (1RM) on a stable floor, stability blue, stability black and BOSU. Electromyographic (EMG) activity was measured trunk muscle such as rectus abdomina (RA), external obliques (EO), internal obliques (IO), multifidus (MF), and low-limbs muscle such as gluteus maximus (GMA), gluteus medius (GME), biceps femoris (BF), rectus femoris (RF), vastus medialis oblique (VMO), vastus lateral oblique (VLO), medialis gastrocnemius (MG), lateral gastrocnemius (LG), soleus (SOL) and anterior tibia (AT) when ascending and descending squat phase. One-way ANOVA repeated measure with Sheffe used to compare the muscle activity on the stable and unstable surface. Squat with BOSU ball induces higher muscle activity of IO, MF, GMA and GME compared with stability and stability blue and blackduring descending motion. Squat with BOSU ball induces higher muscle activity of GMA compared with stability and stability blue and blackduring ascending motion. This results suggested that BOSU ball in the squat could be effective increasing of trunk stability and gluteal muscle activity. However, there was no difference of squat on low-limb muscle with or without instability.

• Physical Therapy Korea
• /
• v.13 no.3
• /
• pp.102-110
• /
• 2006

To improve trunk stability, various exercise protocols were introduced into the clinical field. Trunk and lumbar stability exercises on unstable surfaces are especially recommended to improve lumbar stability. The purpose of this study was to compare abdominal oblique muscle activity during leg raising in hook-lying position among 3 different type of surface conditions (on floor (F), vestibular board (VB), and foam roll (FR)). Sixteen able-bodied volunteers, who had no medical history of lower extremity or lumbar spine disease, were recruited for this study. Surface electromyography (EMG) activity was recorded from the internal and external oblique muscles of both sides. The normalized EMG activity was compared using a one-way repeated ANOVA. The results showed that the EMG activities of the internal oblique and external oblique of the lifted leg side during straight leg raising significantly increased under the FR condition when compared to the F condition. There was no significant difference of the EMG activity in abdominal oblique muscles between the VB and the FR conditions. The EMG activity of the internal oblique of supported leg side during the straight leg raising was significantly greater under the FR condition than the VB and F conditions (p<.05). The composition ratio of EMG activity of internal oblique muscles during straight leg raising was significantly increased under the FR condition. Therefore, straight leg raising exercise on foam roll in hook lying position could be beneficial to improve trunk and lumbar stability.